When installing Windows 7 flies blue screen. When installing Windows XP Blue Screen - Unpleasant Surprise! Uploading drivers during installation XP

Installing a more recent version operating systemCertainly is an important step. But often the Windows XP Stop 0x0000007E error may occur when the seventh system modification is set, which entails the appearance of the so-called blue screen bsod.. What is the reason for this computer behavior and how to deal with it, read further.

Causes of failure to fail with STOP 0x0000007E when installing Windows

At first, you should pay attention to what kind of stage the "seven" installation appears failure. For example, the installation (copy of the installer files and the pre-installation) seems to be successful, but when the first reboot appears, BSOD appears. This indicates the impossibility of the start of the new OS. The reason is the lack of space on the hard disk. Such an explanation is applicable solely for those cases when the formatting of the system partition was not made.

In general, among the most common problems with the STOP 0x0000007E error during installation, most professionals call the following:

hard disk overflow;
bIOS incompatibility with an installed OS;
incorrect BIOS settings;
failures in work random access memory;
conflicts with video card drivers;
damage to the system components of the previous system;
blocking the installer by third-party programs.

You can continue this list, but these are the most basic failures. Separately, it is worth saying that the STOP 0x00007E failure (Windows XP we consider as outdated system, on top of which the seventh modification is installed) may also appear due to the damage to the carrier from which the installation is made. In this case, immediately need to check optical disk or a USB flash drive, and then try to start the installer again from the operating device, after writing the appropriate image to the media used.

STOP 0X0000007E (Windows 7) failure: OS version incompatibility with configuration installed

We proceed from the fact that the installation must meet the requirements new system. Therefore, you first need to check the configuration for compatibility of the processor and RAM. However, this is not the most important thing. Most often, the STOP 0x0000007E error with the appearance of a blue screen is associated with the discharge of the past and future system.

The reason is different file systems. At best, you need to install Windows 7 with a 32 bit architecture (for X64 systems it will require formatting the system partition, set aside for the installation of the new system in NTFS). In addition, it is necessary to have 1 GB of RAM and more, although XP works perfectly on 512 MB of RAM (for some reason, many often forget).

Correction of Winchester Problems

One of the main problems of the appearance of the STOP 0x0000007E failure is the shortage of the hard disk space. To correct the situation at the impossibility of a normal start and old, and the new OS should be loaded into safe modeBy pressing the F8 key after turning on the computer and check the basic parameters in the BIOS.

After that you need to tritely remove unnecessary files And free space, for example, by uninstalling rarely used programs. Pay attention to the fact that no less than 16 GB will be required. disk space For versions of 32 bits and about 30 GB for modifications with a 64 bits architecture.

BIOS version and its settings

No matter how paradoxically sounds, but primary bIOS system And its settings can also cause the appearance of STOP 0x0000007E failure. The problem is that outdated versions BIOS may be incompatible with Windows 7.

To resolve the problem, update the BIOS by downloading new firmware From the official site of the manufacturer. If you do not know how it is done, it is better to contact the service center.

Separately, it is worth saying about setting up the parameters. The STOP 0x0000007E error can be caused by an incorrectly set valve of the hard disk controller. Here you need to find the appropriate section and instead of AHCI set the IDE parameter, after which it is possible to repeat the attempt to install the new system.

Incorrect installation or malnutrition software

Another problem of the appearance of the STOP 0x0000007E failure may consist of the operation of memory schedules. Perhaps they are installed incorrectly or simply failed.

At the check stage, you can use the MemTest86 + utility recorded in portable on removable media or hard drive.

In the first case, you should remove them and put it in the slots as recommended in the instructions. In the second - to withdraw the slats from the slots alternately followed by a reboot every time. It may very well be that some of them will be inoperative or damaged.

Graphic chip drivers

One of the most common reasons that the seventh version of the system does not want to be installed, calling the screen with the STOP 0x0000007E code, is damage to the video card or incorrect operation of the drivers.

Correction of the situation is to boot into sAFE mode Mode, as mentioned above, after which call "Task Manager" from the "Control Panel" or from the "Run" Console (Win + R) by the DevmGMT.msc command, and then use the driver update menu.

You can also first delete the driver or the device entirely, after which the driver is installed from scratch, but not using the system database, but using a disk DriverPack Solution recent versions.

If safe mode is used with support network drivers And there is an internet connection, the installation of this utility of the corresponding software will be made automatically with the download of the latest driver from the official resource of the equipment manufacturer.

If it does not help, you have to check the card for health and in the extreme case replace.

Damage to system files and problems with installed programs

Itself (albeit infrequently) that the appearance of the STOP 0x0000007E failure can be associated with the lack of or damage to the system files of the previous system.

In this case, you will need to load from a disk or reducing flash drive and in the recovery console command line (Usually used a combination of SHIFT + F10). After that, it should register the SFC / SCANNOW command and wait for the restoration of damaged or missing components. Before that, it is better to check the hard disk for complete confidence using CHKDSK / X / F / R combination for this.

Some previously installed programs can also cause malfunctions of this type. Very often, users complain about Antivirus Dr. Web. In this situation (again in safe mode), remove problem applications.

conclusions

As already understandable, problems with the impossibility windows installations 7 can be quite a lot and eliminate them, finding out the reason for the appearance. But if you approach the installation of the system from a practical point of view, it is better to immediately format the system partition in NTFS and install the X64 version. At the very least, it is possible to avoid problems with hard disk, programs and drivers. And in the case of RAM, fundamental measures will have to apply.

If windows installation XP appeared blue screen With the error STOP 0X0000007B, it is highly recommended to familiarize yourself with the material below, as it can be found in it one of the most effective solutions to this problem.

It has long been known that absolutely any variant of the blue screen of death causes a huge number of users an attacks of incomprehensible panic. Nevertheless, almost always the problem can be solved. And if the computer signals the user about the code "STOP 0X0000007B" error, then it is suppressed.

So, the user is scheduled to install Windows XP. The user inserts a source into the drive necessary information, starts the installation procedure. Then everything happens as follows:

The program begins, it seems to work;
The drivers are transferred to the hard disk;
After that, a person should start choosing the installation partition, but it is precisely in between two of these operations and this trouble occurs.

Of course, you can try to restart the process, but, unfortunately, the STOP 0x0000007B error when installing Windows XP will arise at the same stage.

Why is this happening?

The thing is that Windows XP is a rather old Microsoft operating system. The times of its active application have long passed, and from that time a lot has changed. For example, operating modes applied to the hard drives used.

Naturally, this factor leads to a conflict that takes the form of this BSOD error.

Fortunately, there is very effective techniqueallowing you to correct the situation literally in a few minutes. For this, it is absolutely no need to go to the official website of developers, read tons of materials provided, perform some incomprehensible and, most often, unnecessary actions.

Error Correction Stop 0x0000007B

So, if you try to install Windows Windows, an error occurs with this code, then the user must do the following:

The blue screen of death is a generalized concept, which is characterized by the fact that when installing or operating Windows, the blue screen appears sharply with different inscriptions, as a result of which further actions with the operating system becomes impossible. Below it will be about how to be in a situation where a blue screen appears on the computer during the installation of Windows XP.
The problem when you install a blue screen when installing Windows XP, does not give any specifics, which means that theoretically, the problem can cause a variety of factors. Below we will look at how you can independently determine the cause of the problem, as well as what major reasons can provoke it.

Not knowing the error code, it is quite difficult to assume the reason for the blue screen. Therefore, carefully examine the data on the blue screen, in particular, you should be interested in the error code.

Finding an error code, use any search engine in the browser to clarify the cause of the problem, and therefore, to approximate which way to watch. The following recommendations will go in cases where you find it difficult to understand what caused the problem.

Cause 1: Driver Incompatibility with Windows XP

First of all, if you are a user of a more or less new computer or laptop, then you may encounter the fact that in your case there could be incompatible in drivers for your hard disk with the Windows XP operating system, which, by the way, is strongly outdated, and At all ceased to be supported by Microsoft.

In the event that your hard disk has a modern SATA connector, then the problem can be tried to eliminate, switching to the BIOS on iDE modeThat will ensure compatibility between hard disk and Windows XP.

To do this, send a computer to a reboot (or simply turn on) and at the earnest switching stage, start clicking on the BIOS entry key. As a rule, in most cases in hot key Can perform F1, F2 or DEL.

Entering the BIOS, you will need to find the mode responsible for changing the SATA mode. IN different versions BIOS It can be located and called differently, in our case the setting you needed in the section "INTEGRATED PERIPHERALS".

In it we found the option "Onchip Sata Type"By clicking on which, we are invited to select the desired parameter (we are interested in IDE). Save tincture, we leave from the BIOS and try to install Windows XP again.

Reason 2: Outdated Windows XP Build

Old builders of Windows XP do not include updated versions of drivers that can support devices that have released many later than this version of the operating system. In this case, you will need to try to search the Internet another. build Windows. XP, which includes updated versions of drivers.

Cause 3: Availability of malfunctions in a disk device

Sustain this problemShe is much more serious because it implies a problem in the hard disk.

Check it easy - try to install a more modern version of Windows, for example, 7 or 10. If new windows version They do not want to get up, the problem can really go in malfunction of disk devices.

First you need to look under the case system Block (laptop) and check the connection of loops of your hard drives. If everything is connected normally, you should check hard on bied sectors And, if necessary, perform treatment. To do this, there is a diverse selection of programs that can work both from under Windows and in your own environment, for example, it is worth highlighting a program. HDD Regenerator..

If results hard checks The disk was identified a large number of Bad sectors, there is a chance that your hard drive has failed. You can check this by connecting another hard disk to the computer and trying to install the operating system already on it.

Cause 4: RAM issues

Often the blue screen of death when installing the operating system signals problems in operational memory problems. You can make sure that you can verify the operational memory for errors.

To do this, you need to download the program computer. memtest86.. In the screenshot, you can see what program file you will need to download.

Make blood flash drive with the program. You can write it in any program to create loading media, for example, Ultraiso..

Once the record is completed, you will need to connect a flash drive to a problematic computer and log in to the BIOS by installing a flash drive (or disc) as the main boot media.

After running from the bootable media, the utility window will appear on the screen, after which the utility automatically, without any additional actions on your part, will start scanning RAM. Test Status You can see near the item "Test".

In the event that, according to the test results, the utility will detect errors in the operation of RAM, they will be highlighted in red. If you confirmed the problem, you will need to carefully examine the memory surface - if the contacts are contaminated, then cleaning with an ordinary natural cavity can help solve the problem. In more serious cases, the problem module will be replaced.

Actually, these are the main reasons that may affect the inability to install Windows XP. We hope these recommendations helped you perform the normal installation of the operating system.

Installing Windows XP to modern iron is often conjugate with some problems. When installing "rolls out" various errors and even bsods (blue screens of death). This is due to the incompatibility of the old operating system with equipment or its functions. One of these errors is bsod 0x0000007b.

Blue screen with such code can be caused by the absence of the built-in AHCI driver SATA controller, which allows the use of various functions for modern drives, including SSD. If your motherboard uses this mode, then Windows XP will not be able to install. Consider two methods to eliminate the error and analyze two separate private events with Intel and AMD chipsets.

Method 1: BIOS Setup

Most motherboards have two SATA drive modes - AHCI and IDE. For the normal installation of Windows XP, you must enable the second mode. It is done in BIOS. Go to settings motherboard By pressing the key several times Delete. When loading (AMI) or F8. (Award). In your case, it may be another key, it can be found out by reading the manual to the "motherboard".

The parameter we need, mostly, is on the tab with the title "Main" and called "SATA CONFIGURATION". Here it is necessary to change the value with "AHCI" on the "IDE"Press F10. To save the settings and restart the car.

After these windows actions XP is likely to be installed normally.

Method 2: Adding AHCI Drivers to Distribution

If the first option did not work or in the BIOS settings, there is no possibility of switching SATA modes, you will have to manually integrate into the XP distribution required driver. To do this, we use the NLITE program.

We go to the official website of the program and download the installer. It is exactly the one that is highlighted in the screenshot, it is intended for the distributions of XP.

If you are going to integrate, working directly in Windows XP, you must also install Microsoft .NET Framework 2.0 from the developer's official website. Pay attention to the discharge of your OS.
Installing the program will not cause difficulties even at the newcomer, just follow the prompts of the wizard.
Next, we need a compatible driver package, for which it is necessary to find out which chipset is installed on our motherboard. You can do this using the AIDA64 program. Here in the section « Motherboard» , tab "Chipset" There is a necessary information.
Now go to the page on which packages are collected, perfectly suitable for integration with NLITE. On this page, choose the manufacturer of our chipset.

Download package.
The archive that we received when loading must be unpacked in a separate folder. In this folder we see another archive, the files from which also need to be removed.
Next you need to copy all files from installation disk or image to another folder (new).
Preparation Completed, launch the NLITE program, select the language and click "Further".
In the next window, click "Overview" And choose the folder to which files from the disk copied.
The program will check, and we will see the data on the operating system, then click "Further".
The next window simply skip.
The following action is the choice of tasks. We need to integrate the drivers and create boot image. Click on the appropriate buttons.
In the driver selection window, click "Add".
Select item "Driver Folder".
We choose the folder into which we unpack the downloaded archive.
Select the version of the driver's desired bit (the system that is going to install).
In the Driver Integration Settings window, select all items (click on the first, clamp Shift. And click on the latter). We do it in order to be confident that necessary driver Present in the distribution.
In the next window we click "Further".
Run the integration process.
Select mode "CREATE Image", Zhmem. "Create ISO", choose a place where you need to save the created image, give him a name and click "Save".
The image is ready, we leave from the program.

The resulting file in ISO format must be recorded on the USB flash drive and you can install Windows XP.

Above, we looked at the option with the Intel chipset. For AMD, the process has some differences.

Conclusion

We disassembled two ways to eliminate the 0x0000007B error when installing Windows XP. The second may seem complex, but using these actions you can create your own distributions for installation on different iron.

Operational windows systems XP and 7, despite the termination of official support from microsoft., and a satisfied powerful advertising campaign relative to dozens, continue to occupy leading positions in the market of operating systems. Their reliability is checked for years and proved by millions of contented users. However, even when using them, errors that interfere with full work may occur.

One of them is an error 0x0000007b, as a result of which the so-called blue screen of death appears, the computer does not respond to your actions from the word "at all". The only output is rebooting, but it does not help in such cases. Most often a problem occurs when reinstalling Windows XP or 7, and manifests itself when the system is loaded, although this may occur at other situations. It is noteworthy that the situation can be repeated even on a new computer or laptop.

In this article, we will consider for what reasons an error occurs 0x0000007B when installing Windows XP or Windows 7, as well as all solutions. If you read everything and you will carefully follow the instructions, you will easily fix everything.

In fact, the reasons why blue screen arises with error Stop. 0x0000007B, quite a lot. And they all directly depend on what operation at this point you are performing. The only thing between them is generally installed Windows XP, as well as the launch of this version or more new Windows 7. So, what could be the cause of the problem?

When starting the system:

Damage to important system files responsible for starting the system.
Viruses that can penetrate the system very deeply and affect the operation of the system.
Physical defect of a hard disk of a computer or error in its work.
Inserted into a USB connector flash drive.

This is how 0x0000007B error looks like

When installing the system:

Incorrect installations bios.which is why the failure occurs.
Incorrect operation of drivers used in the load controller. If they are damaged, the controller simply cannot execute the Windows installation procedure to the end.
No support hard disk or sCSI controller Installed operating system. It may be on modern models of computers or laptops, since XP is already considered outdated.

Methods Solutions

During system launch

Run the latest working configuration

Since the failure may be temporary and random, in Windows 7 and XP, it is possible to return to the last working configuration. What does it mean? During operation, the system in a special partition on the hard disk copies the working files responsible for starting the system and its full work. Also, from time to time, an image of the system's working state is created, in which everything works properly. A few such images are stored on the hard disk. Each time you launch a computer, the system automatically selects the latest and over time older settings are removed. Therefore, if a 0x0000007B error occurs when startup, try opening the last workout.

To do this, while running the operating system, press the F8 button to exit the download menu. In order to start this mode for sure, and do not sleep, click the button several times. You will see a list of download options: secure mode, download logging, debug mode and others. You need to select "Last Successful Configuration (optional)". If everything goes successfully, normal will begin download windows. If this did not happen, this method will not help you, so try one of the following.

Select "Last successful configuration (optional)"

Checking disk on errors

Hard disk - not the most reliable component of your computer, especially if it is not solid. It has moving mechanisms, consists of a magnetic surface and the reading head. If you use a laptop and often work on it directly on the go, perhaps even in transport, there are damage to some sectors of the hard disk. If the sector will be damaged on which system files, essential for windows work 7 or XP, the launch will be impossible. To make sure that your hDD With errors or still any reason is possible, it will be necessary to use the branded utility of the tested disk. But how to open it if Windows does not start?

Usually such an inspection is quite enough to restore performance. If the disc is damaged so much that standard remedy Windows cannot cope with the problem, try using specialized resuscitation software. hard disks. If the problems were not detected, but the error 0x0000007B is repeated, try the following method.

Check for viruses

Some malicious files are so covered and dangerous that they penetrate deeply in system section Windows and damage systemically important components, resulting in an error 0x0000007b. If the previous two ways do not help you, try checking for viruses by downloading the computer in safe mode. Here are step-by-step actions that you need to perform:

When installing Windows XP

Incorrect BIOS settings

Most frequent causeWhat you can disturb the error 0x0000007B when installing Windows XP, is the incorrect mode of operation of the hard drive. The fact is that all modern connects interface SATAwhich provides reliability and high data transfer rate, and uses the modern ACHI standard, which allows you to use all SATA features. The Windows XP itself does not support this standard, since in those days it has not yet existed. Accordingly, due to this incompatibility, the 0x0000007B error occurs when Windows XP is installed and the blue screen comes out.

To return efficiency in bIOS settings Place the default IDE mode that will work in SATA compatibility mode. Where is this setting item? How to set the desired parameter?

Turn on the computer and go to the BIOS. Depending on the manufacturer of the laptop or motherboard of the system unit, the keys, or their combinations that need to be pressed to go to the BIOS, may differ. Most often it is F2, Del, ESC.
Depending on the type of bios used, the menu location may differ slightly. This is what may need to click:
- Main menu - Advanced - Onchip Sata Type - Native IDE - F10 to save settings.
- Main menu - Advanced - IDE Configuration - Compatible - F10 to save settings.
- Main menu - Main - SATA MODE - IDE MODE - F10 to save the settings.
- After you activate the mode, repeat the installation of Windows XP.

No Driver Controller

Windows XP is known for its assemblies from various programmers who either cut some components to facilitate the image and ability to work even on old and very weak systems, or embed additional software. When using cropped assemblies, you can very often encounter the fact that they do not have the required controller driver, due to which the XP installation is broken and the blue screen is knocked out with an error.

The only correct solution will be the download of another operating system image with an already built-in driver. To do this, you can search another assembly on torrent trackers and carefully read the description.

Conclusion

Now you know how to deal with an error 0x0000007B when installing or launch Windows 7 or Windows XP. We described the most common causes of its occurrence, as well as the most effective methods of solution. If nothing helps did not help, the blue screen continues to pop up, then it is worth thinking about buying a new computer or a laptop or simply completely reinstall the system, download a clean and original image. In the comments, we ask you to specify whether you managed to get rid of the problem on our recommendations.

BSOD: STOP 0x0000007B - began to appear on one computer very often, even after reinstalling Windows From scratch, most likely it can be suspected that the reasons may be:

1) due to the download of content, where the beautiful button is big to the big download, as a rule, it is also not a fact, everything is masking beautifully under viruses, viruses or remote control In the form of Backdoor - can damage the HDD / SSD boot sectors. IN Manual mode, In the floor automatic or even automatic without the participation of a person on the script. By the way, Windows 7 x64 SP1 suffers this time - this is not some kind of Windows 10, there would be the same if there was a mistake the same. After all, with Windows 7, it was not desirable modifications, or rather too many processes and other services. As a rule, this system for consoles and mobile devices It was created, but for a computer. The only thing that appear visible on the DirectX 12 is some one that essentially does not have the support of most games, even for them there is no point in doing this, a normal company will definitely make a choice in DirectX version Running games like Resident Evil 5 - Run from DirectX 9 and from DirectX 10, 11 even for VR. And not to force only a strict one DirectX such that version, many years ago there was a choice for not many games, even by the way S.T.A.L.K.E.R. - And that could be changed DirectX to the 11th version, it is a call of Pripyat - it is said to be improved to this day.

2) incompatible with video card, audio driver especially most often Realtek AC 97 - For example, it may be downloaded old versionOr downloaded not from the official site, it was only on Windows XP SP2 / 3 - as far as I remember and many years ago.

3) Partially compatible driver On the video map, even so, but very rare, 1k100, that first everything will work perfectly. But here the driver on a video card either has the latest version for old card models only, which is incompatible with Windows system kernels and even BSOD can serve. Still know what's most often ATI Radeon. not HD versions - suffer even worse from the latest versions of the driver, so Catalyst is recommended - put latest version. And in the HD series - if the driver is installed, the image shows, but then a few weeks after windows reboot - then it says either the video card itself is marked already, the chips do not issue due images to the data output, or the chips cannot process the fulfillment that should not be processed. Most often leads to an image at all, but very rarely to BSOD 0x0000007b.

The most important thing. By default, the licensed version of Windows XP / Vista / 7 / is disabled. Windows must be included to study a symptom of a technical error, the error code can be found for the cause. Here is the main problem that it is disabled, few people know about it, so the favorites can receive requests for bSOD errors - Western Windows creators - since when installing Windows does not have a function - to show the error code when the Windows YES / NO system fails. For this, the base is filled with BSOD - only the favorites and write errors from the experience that only chosen. Favorites repair systems are no less than twice as expensive (in fact, should, since they can correct these errors much better than noob sibot / noob) noob. Kettle and other.

By the way, everything is written here 100% of the truth, personally my experience.