I have already mentioned in my articles SSD Discah, he said that they were faster than ordinary and with their help you can upgrade a computer. And they would seem to install the trivial thing, which may be easier, take off old hard disk, put a new SSD. You install Windows on it and rejoice, but in fact everything is not so simple. The fact is that in order to squeeze the maximum speed with an SSD disk (and otherwise, why use it), you need to switch to the BIOS aHCI mode ADVANCED HOST CONTROLLER INTERFACE). And here they can begin surprises ...

So, I have old computerwho decided to profite and install an SSD disk. In BIOS switched the AHCI mode. To do this, entered the BIOS (press the DEL or F2 button (maybe other keys depends on the model motherboard) When you turn on the computer) in the "Main" menu selected "SATA Configuration".

And in "Configure SATA AS" chose "Ahci"

Saved the settings, rebooted the computer and started installing Windows. But it was not there, an error arose:

Started changing the BIOS settings, even updated his version The result was one- constantly appeared this error. As a result, I decided to select IDE mode and install Windows.
The installation was successful, then I decided to try to switch again to AHCI mode, but a similar trick failed and Windows simply did not boot (in principle I expected a similar result). Then I decided to do so - switch again to IDE mode, go to Windows and in the registry editor change the mode to ACHI.

Returning IDE mode, Windows has been successfully loaded, now it is necessary to make changes in the registry. To do this, open the registry editor - press the key combination "Win" + "R" and enter the REGEDIT.

In the Registry Editor, go along the path "HKEY_LOCAL_MACHINE \\ SYSTEM \\ CURRENTCONLSET \\ SERVICES \\ MSAHCI", find the "Start" parameter, open it with a double click. In the "Value" field, enter "0".

All, system can be restarted and set AHCI mode to BIOS. As a result, everything worked, SSD drive worked in ACHI Windows mode successfully loaded and worked at times faster than with a conventional hard disk.

So, if your old computer stopped pleaseing the speed of his work- installing SSD. disk, in my opinion, the perfect solution. But no need to forget about the minimum size random access memory - 2GB Well, the processor is preferably 2 kernels at least 2 GHz.

I hope this article helped you avoid mistakes:

Installing Windows for this disc is not possible. Perhaps equipment this computer does not support downloading of this disk. Make sure that the controller of this disk is enabled in the computer's BIOS menu.

And helped product up your computer and increase its performance and speed.

During the installation of the operating room windows systems 10 can occur various errors. As a rule, they are associated with the wrong BIOS settings or incorrect work Computer component or laptop components. One of the frequent errors sounds like this: "Installing Windows to this disk is not possible. Perhaps the equipment of this computer does not support the download from this disk. Make sure that the controller of this disk is included in the computer's BIOS menu. Yes, the trouble happens when the disc is really cut off and no longer works. But most often the reason in the other.

SAMI frequent cause, Because of which this fault occurs consists in settings of the SATA controller when working with old hard drives. Try to start when you turn on the PC to enter the BIOS and change the operation of the controller with the ACHI on the IDE.

On more modern motherboards with UEFI, instead of a regular BIOS can help change work on Legacy mode.

If none of these manipulations helps, then return everything as it was. The reason is most likely in the other.

Sometimes the error "Make sure that the controller of this disk is enabled in the computer's BIOS menu. It may appear because the boot record hard Disc and it must be restored. To do this, when you start installing the Windows 10 operating system, click on the "System Restore" button and go to the "Diagnostics" menu \u003e\u003e »Advanced parameters» \u003e\u003e »Command line», or simply press the SHIFT + F10 key combination. A black window of the Windows console will appear:

In turn, type the team:

Bootrec / FixMBr BootRec / FixBoot BootRec / RebuildBCD

Each of them must be completed successfully. After that, reboot the PC and try to start the installation again. Usually, the disk controller error in the computer's BIOS menu is solved and then everything goes without any problems.

set-os.ru.

Windows installation to disk is not possible

During the installation of the operating system, at the formatting stage of disks and create partitions, the user may encounter an error "Installing Windows to this disc. Perhaps the computer equipment does not support the boot from this disk. Make sure that the controller of this disk is included in the computer's BIOS menu.

Why does such a mistake arise and how to fix it?

READ ALSO: Codes windows errors 10 and ways to troubleshoot

Ways to solve the problem

Often, an error when it is impossible to create a partition to install a new operating system, it occurs on old PCs with Windows 7. However, other operating systems starting with XP and ending with Windows 10 are also not insured against such a malfunction.

The following factors may be the cause of such an error:

• Not correct settings SATA operation parameters;
• Equipment specificity (availability of additional SSD and SCSI cards).

Method number 1. Through Biosa settings

To fix this error, it is worth loading into the BIOS and set the mode of operation of the hard iDE disk. To do this, carry out the following:

• Restart the PC and press "F8" several times to get into the BIOS.
• We find the "Advanced" or "Integrated Peripherals" section and select "SATA MODE" or "SATA RAID", "CONFIGURATION SATA" in it (path to settings depends on the motherboard model). Change the mode of operation with AHCI or the other on the IDE.

• Click "F10" and reboot PC. We repeat the installation of the system.

If your PC has new firmware BIOSA, then instead of the IDE mode it is necessary to enable EFI boot. To do this, carry out the following:

• Loading in Bois-UEFI and go to the "BOOT" section. We find the item "UEFI / LEGASY BOOT" and set "Enabled".

• We maintain changes and reboot PC.

It is worth noting that this change is not excluded the emergence of a new error, which is associated with sections MBR or GTP.

See also: How to install Windows 10 to the GPT and MBR drive?

If an additional cached SSD or other drive is installed on your PC or laptop, it is possible that the problem occurs exactly because of it. To correct the problem, perform the following actions:

• Determine the model and version of the device. Go to the developer's website and download the drivers that are sealed to the archive, and not laid out by a separate EXE. File.
• Unpack files on the USB flash drive.
• Run the installation of Windows. At the stage of selecting the volume, click on the "Download Drivers" button.

• A new window will open. Press the "Overview" button and specify the path to the drivers. Click "OK" and "Next".

• We repeat the attempt to select a volume to install the system.

Method number 3. If the error is associated with GPT or MBR format

If during windows installations 7, 8 or 10 You have an error "Installing Windows to this disc is impossible. Selected disk has style gPT sections"It is worth changing the GPT format on the MBR. To do this, perform the following actions.

• Keep all the data from the disk C, as it will be formatted. Also will not prevent information from local disk D.
• Open command line With administrator rights and enter the following commands:

1. diskpart;
2. list DISK;
3. select Disk number (specify the disk number to which you will install Windows and what problems arise);
4. clean (will be cleared of the entire disk);
5. cONVERT MBR (changed format);
6. exit.

After formatting the partition it is necessary to restart the PC and repeat the attempt to install the OS.

You can also perform the same actions more simple way. In the BIOS in the "BOOT" section in the UEFI / Legasy Boot point and set Enabled, and in " Secure Boot"- disabled. After that, delete all sections and create new ones. The format will automatically be changed.

Softikbox.com.

Installing Windows for this disc is not possible. Check the BIOS setting

No comments: 4

Hello everybody! When installing Windows on a laptop, I have an error: installing Windows to this disc is not possible. Perhaps the equipment of this computer does not support the download from this disk. Make sure that the controller of this disk is enabled in the computer's BIOS menu.

I read on the Internet, someone says that you need to switch from ACHI to IDE. Switched - did not help. I watched the BIOS settings, well, in the laptop it is so simple that in general there is almost nothing to choose ... I dropped the BIOS did not help ... then inserted back the disk with Windows and pressed the system recovery (this is where to install the button). Chose a team building. By the way, you can run it SHIFT + F10.

Write bootrec / fixboot. After that we try to install. I helped me.

The fact is that Windows could not find the bootloader and did not understand what to do. This is how the Windows installation error is solved on this disc.

AlexZSoft.ru.

Installing Windows for this disc is not possible.

For reinstalling Windows 7 The laptop has unexpected problems - BIOS and windows Installer Seen hard disk, it was allowed to place it, add / delete sections, but then it was not going on, issuing a strange message:

Installing Windows for this disc is not possible. Perhaps the equipment of this computer does not support the download from this disk. Make sure that the controller of this disk is enabled in the computer's BIOS menu.

Why is it strange? In general, the support of the AHCI mechanism (Advanced Host Controller Interface) is declared from Windows Vista. and installation disk With Windows 7 licensed.

Well, God, God, you can seek to blame for a long time and stubbornly, it's easier to climb into the BIOS and switch the AHCI Mode Control C mode on. After that it will be possible to disable Native Ahci Mode. Subsequently, you can return the settings back by installing the system and all drivers.

If you consider an article useful, do not be lazy to put like and share with friends.

mDEX-NN.ru.

Installing Windows for this disc is not possible (Solution) - Programming, Administration, IT

Installing Windows for this disc is impossible (solution)

In this instruction, it is reported in detail about what to do if the Windows installation is reported to you that it is impossible to install Windows into the disk section, and in details - "Installing Windows to this disc is not possible. Perhaps the computer equipment does not support the boot from this disk. Make sure that the controller of this disk is included in the computer's BIOS menu.

If you still choose this section and click "Next" in the Installation Program, you will see an error reporting that we could not create a new one or find existing section With a suggestion, view more information in the installation program log files. Below will be described how to correct such an error (which can occur in Windows 10 installation programs - Windows 7).

As you are increasingly on computers and laptops, users occurs a variety of partition tables on disks (GPT and MBR), modes hDD works (AHCI and IDE) and download types (EFI and Legacy), rapid and errors when installing Windows 10, 8 or Windows 7, caused by these parameters. The case described is just one of these errors.

Fixing the error "Installing on this disc is not possible" using the BIOS settings (UEFI)

Most often specified error It occurs when Windows 7 is installed on old computers with BIOS and Legacy Download, in cases where the AHCI (or any RAID, SCSI modes) is enabled to the BIOS in the SATA device parameters (or any RAID, SCSI modes).

Solution in this particular case - go to the BIOS parameters and change the mode hard work disk on IDE. As a rule, this is done somewhere in the Integrated Peripherals section - SATA MODE BIOS settings (several examples in the screenshot).

But even if you do not have a "old" computer or laptop, this option can also work. If you install Windows 10 or 8, then instead of incorporating the IDE mode, I recommend:

1. Enable EFI boot in UEFI (if it is supported).
2. Boot from the installation drive (flash drive) and try the installation.

True, in this option, you can meet another error type, in the text of which will be reported that the MBR partition table is located on the selected disk (the correction instructions are mentioned at the beginning of this article).

Why this happens and I myself understood (after all aHCI drivers included in windows images 7 and higher). Moreover, I was able to reproduce the error and to install Windows 10 (screenshots just from there) - just changing the disk controller with IDE on SCSI for virtual machine Hyper-V "First Generation" (i.e. with bios).

Whether the specified error will appear when the EFI-download and installation on the IDE mode will not be checked, but I admit this one (in this case, we try to enable AHCI for SATA disks in UEFI).

Third Party Drivers AHCI Disc Controller, SCSI, RAID

In some cases, the problem is caused by the specificity of the user's equipment. The most common option is the presence of SSD caching on a laptop, multi-disc configurations, RAID arrays and SCSI cards.

Computers are complex devices whose work provides many different elements. One of them is a SATA controller. What is myself this device? How to work with him? How to take care of his speed? Here is an incomplete list of questions that will be discussed within our article.

Is a technology by which storage devices like a hard disk and optical wire can exchange data on high-speed cable with motherboard. It is optimal to use the connector with the smallest number. Ideal are subject to SATA0 or SATA1. For possible is the use of other ports.

When working with hard disks, it is originally necessary to use SATA0. It is installed on the system carrier. Each subsequent should have a number one more and so on. If there are several hard disks And the RAID mode is used to increase the storage location, one wire is connected to the connector, and then everything else is supplied to the controller.

Modes of work

Controllers determine how the hard disk will exchange data with the motherboard. There may be three interaction principles:

1. SATA IDE controller operation mode. The easiest option. With it, the hard disk functions as an IDE or rata. In this case, it has limited potential, and also does not differ in speed. But this mode is very valuable if it is necessary to ensure the compatibility of interaction with the equipment, which is already outdated. You can also use it in cases where the computer has only one hard disk and does not need to use various functions of the drives.
2. SATA AHCI controller operation mode. In this case, the use of advanced drive functions is possible. As an example, you can bring Native Command Queuing and "hot" replacement. Also, a significant advantage is a high interaction rate (if compared with the previous option).
3. Operating mode rAID controller. With this setting of several separate hard drives, you can create a single data storage array. It is distinguished by the redundancy of information, as well as higher speed. The first is achieved through the creation backup Hard disk, and second - bundle disk space. When this mode works, AHCI functions with it.

Notes

Initially, it is necessary to set the mode of operation in which the SATA controller will be operated correctly for a laptop or computer, and only then to engage in the operating system. After all, if it is done later, the OS may incorrectly work until the refusal. So, this may occur due to the fact that the disk driver will be disabled or the wrong BIOS parameter is used.

Causes of faults

Suppose PC stopped working with a hard disk. This malfunction may have several reasons:

1. Cables are loosely connected.
2. Winchester failed.
3. It does not work or slows down the SATA controller.

In the first embodiment, you need to check the cable fit density. In the second, most likely, you need to replace the device. And in the third - to set the correct settings. For such changes, administrator rights are necessary. If they are, you can start solving a malfunction.

How to enable SATA controller in computer bios?

Initially, you need to go to the BIOS. There is no single standard here - each machine uses a separate special key to do this. To find out, you need to get acquainted with the instructions on the screen, which occurs immediately after turning on the computer. Moreover guaranteed result It must be pressed more than once.

After the input is successfully completed, you need to find an Integrated Peripherals item. If it is not, it will be suitable for anyone who is consistent in meaning. It contains all the parameters that belong to the internal capabilities of the motherboard. Now you need to find Onboard Sata Controller. If it is not, just look for any entry where the "SATA controller" is written. This parameter can only be set to disabled and enabled (respectively disabled and enabled). It is necessary to trace it to be activated.

You can click on the F10 and the input button to save changes. If this is not done, the system itself will propose to make these actions. After that, you should restart the computer and once again go to the BIOS to make sure that the Winchester was detected. You can understand this by the Standard CMOS Features item. Now we know how to enable the SATA controller. Let's deal with the modes.

AHCI connection

This is done with the help of the same bios. To make changes to go to the Control window. After that, you need to search for IDE, AHCI or RAID. They must go along with SATA. Also additionally on some devices is the word "Mode". The same mode that we do not need, turn off, and the necessary, on the contrary, connect (it all is done also by changing the disabled to enabled and vice versa).

If when you try to change the mode, a message is displayed that no disk is not located, which means there are no required drivers. Therefore, it will be necessary to enter the operating system and with the administrator's rights first to establish them. This can be done and using the OS installation disk. But still less costly time is the first option. Also do not forget that made in basic system I / O changes need to be saved to start acting. How to do this, it was said in the previous paragraph.

In general, here, how to switch the SATA controller to AHCI mode or other, which will be necessary. At the same time, an accurate following instructions are important to not touch anything superfluous. Now let's pay attention to two options that can be useful when configuring a computer. Moreover, the main topic of the article is already disclosed, and we will now deeper our knowledge.

SATA CONTROLLER MODE.

This option is used to indicate the operation mode. This we already spoke. Now let's pay attention to how and what works in this case. If you set the IDE mode, then the need to use additional drivers when working with technique, which uses this technology. RAID mode is compatible with all OS starting with Windows 2000. The only feature is that there will be obsolete carriers for drivers (if the technique of the same year of release, which is operating system). Otherwise, their role can successfully execute a flash drive or CD. But talking about creating makes sense only if there are at least two hard disk. Positively on their work will affect the same brand and volume. And if the party and Firmware coincide - it is already the ideal conditions for using this regime.

Ansi is more new technology And with old (relatively) systems are not compatible. Due to the fact that this mode is positively affecting the speed of technology, it is recommended to stop on it. Moreover, if RAID and ANSI can still be run on representatives of operating systems and computers starting from generation 2000, with Windows 9X they will not help: they simply do not have the drivers that would combine work software and equipment. Note that the changes must be made before the OS is installed. If you change the mode when the operating system is already installed, you can detect on your computer " blue screen Death ", on which information about the error and the impossibility of correct work will be displayed. If there is no desire to see him and demolish the OS, then it is necessary to enable the controller driver to one that will work with new settings.

History of development

The first of the family controller is considered to be SATA 150. It is an interface that uses serial tire data transmission. Works at a frequency of 1.5GHz, thereby providing throughput 150 megabytes per second. The standard has spread due to a number of advantages that previous developments have not been. So, the architectural advantages of the tire, the small size of the connectors and the cable, convenience when used and the overall reliability of the connection played a role. Also, when connecting to one port, two devices does not arise here conflicts and problems do not appear.

The second generation of SATA 300 provides operation at a speed of 300 megabytes in one second. Theoretically both options are compatible, but problems are not excluded. But, justice for the sake of, it is worth saying that even the most modern hard drives have not yet learned to act faster than 130 megabytes per second, therefore there is no particular sense to chase the numbers in this case. Therefore, when using the types of controllers there is no difference. It is important only that the first is connected.

Conclusion

The SATA controller is definitely an important part of any computer. This is a device that allows us to access data, which represents value. Also, it is also worthy of what success managed to achieve the developers of this part in speed. In addition, this suggests that there is a significant reserve for increasing the capacity of hard drives without finalizing data transfer technology, which makes it unlikely that it will be outdated and unnecessary in the next few decades.

»» Error "Installing Windows for this disc is impossible"

Error "Installing Windows for this disc is impossible"

Sometimes when installing Windows 7, 8 or 10, you can encounter a problem that is that when trying to establish a system on hDDThe system issues a warning: "Installing Windows to this disc is not possible. Perhaps the equipment of this computer does not support the download from this disk. Make sure the controller of this disk is included in the menu. Computer BIOS ».

The problem is usually characteristic of old computers and laptops, but occasionally manifests itself on a new hardware. This happens as a rule in the event that bIOS settings computer in work parameters hard disk Mode is enabled Ahci. or any other other than IDE. Therefore, we go to Bios. Computer and install the mode of operation of our disc as IDE. Usually this setting is in section Integrated.Peripherals. or Advanced, and she is usually called SATA.RAID /Ahci.Mode., SATA.Mode., SATA.Ahci.Mode.,Configure.SATA. Or another, similar to the sense.

I also met this method of deactivation of the regime:

1. We switch the mode using the setup AHCI MODE CONTROLin mode Manual.
2. At the same time, we have an accessible setting. Native Ahci Mode.which we need to switch to Disabled..