Installing Windows 7 freezes after starting. External evaluation of devices

At some point in time, it doesn't matter what, I wanted to install / reinstall the operating system on the computer. Cave distributions, set up settings in Bios and, most importantly, prepared to the loading and installation process morally. But it was not there. When installing Windows 7, a computer suddenly hangs, without feeding the slightest signs of life. Miracles, and only. However, before grabbing the head, run behind Validol or rushing to write an angry letter to Bill Gates, it is worth thinking about why the problem still happened in the system.

In this case, the reasons will directly tell us the investigation and, accordingly, all possible methods Solving the problem why Windows 7 is installed for so long.

Problems of problem and their causes

Symptoms of such a "disease" in the installation of the operating system can be different:

At the same time, the reasons for the hangs of the PC in each of these cases are among the same. In particular, the system can be loaded for a very long time due to:

troubleshooting problems;
problem with RAM or power supply;
no contact S. motherboard;
closure uSB connector or malfunction in the drive;
incorrect BIOS settings;
errors in the formation of the OS on the distribution;
damage to the boot disk (flash media).

Thus, the reasons for the fact that the computer freezes at the beginning, middle or when the operating system is completed, can be divided into internal (1-5), directly related to the work of the PC, and external (6-7). Based on this, the solution solutions will also differ among themselves.

Troubleshooting options

1. Waiting for response

No matter how trally sounded, you can just wait for the end windows installations. There are no cases when after 10-45 minutes of waiting, the system responded and was installed in the future without failures. How can this be explained? Unambiguous, all the more official response to this question it will not work. However, as practice shows, very often a similar problem accompanies installing Windows to a computer with aMD processor and Gigabyte motherboard.

2. Replacing Windows 7 Distribution

If the expectation of the system response does not help and the PC is still freezing, it is worth trying to replace or test it on another computer. If the reason was in it or in the image recorded on it, the problem with the braking of the computer, understandable, with the replacement of the distribution will disappear.

Here, we note that the problem may not be in the loading disk (flash drive), but in the drive (USB connector), with which it is loaded. To identify such a problem in the work of the PC is easy. It is enough to test for the performance of the drive (USB connector) using any other disk (flash drives).

3. Remunifying BIOS.

Definitely in BIOS there are two parameters that can affect the speed of the computer, namely:

SATA MODE (Onchip Sata Type);
FLOPPY DRIVE / DRIVE A.

It is best to adjust the work of each of them. In the first case, you will need to enter the Integrated Peripherals section and select the SATA Mode or Onchip SATA Type value AHCI:

In the second case, the FLOPPY DRIVE (Drive A) will have to deactivate. You can do this in the Advanced section in the BIOS:

In addition, you can try to reset the computer boot settings set before starting the Windows 7 installation process.

4. External appliance assessment

If none of the methods described above did not help, it is very likely that the cause of the problem lies in the "filling" of the computer. To begin with, it is necessary to estimate the external state of the devices. To do this, take a screwdriver in the hands, twist the bolts from the system unit and alternately check whether there are drums, the smell of burning and other faults:

power supply;
motherboard;
winchester;
RAM, etc.

It is clear that if the result is positive, the decision will be very simple - change the damaged device and forget about the problem. If the external inspection did not give anything, we take test hDD and work random access memory.

5. Testing of hard drive and RAM

Test a hard disk for the presence of broken sectors and other faults can different programsFor example, such utilities as.

Hello dear friends! I caught on these weekends to me the computer for which I needed to install Windows 7. But there was a problem with which I met for the first time. When I started installing Windows 7, the installation window appears (first window, language selection). And then the seven was very long installed. If you have the same problem when Long installs Windows 7, I. the installation window does not appear., now I will write how to solve it. At least Rusking as I solved this problem.

I will probably begin first. They called me and asked to come and see the computer, and then: the Internet does not work (there is intertertelecom), the antivirus someone shows all the time, nothing starts, etc. In short full set all sorts of different breakdowns. And with this computer, I have already dealt with a powerful such "machine", new, only here Windows XP is installed there, not that it would be bad, just surprised me. And when I asked the owners why it is worth Windows XP, they said that they were installed in the store. I said that it would not be bad to put a seven, all the same she's newer, and on such a gland.

I came for the second time, turned it on, and there was something incomprehensible. Toli, this virus worked so much, or the children :), but there Avast launched some warning, there were almost no icons on the panel of notifications, the Internet did not respond to an attempt to open the connection, the topic of registration was changed, and the standard did not work out. And many more different unpleasant moments.

I looked and decided that it would be easier to demolish everything, format the C drive C and. Explaining the entire owner of the computer, we decided that we would do.

Everything is fine, the computer rebooted, and went to boot from the installation disk. The file download bar when installing Windows 7, and when a window should appear with a choice of language, nothing happened. The window did not appear, there was only a screensaver (well, such as when installing the seven) and the cursor. I waited a minute three and rebooted the computer. I realized that something was wrong. I decided to once again go to the BIOS and see the settings. Now it is clear why the store installed Windows XP, most likely it was not possible to install the seven.

I dropped problems with my installation disk immediately, I installed more than once. Yes, and I had an exact copy from which the Windows 7 installation window also did not appear. In Bios, I did not see anything strange, and. It did not help, Windows 7 was not installedThe window with a choice of language has not appeared. I decided to open system unit And see how and what is connected there. I did not see anything interesting. A hard disk and optical drive was connected via the SATA interface.

I tried to start the installation again. I launched everything just as background, and there are no windows with a choice of language. I decided to wait. Somewhere in 5 minutes a window appeared with a choice of language, well, at least something I thought. Pressed further, there was an inscription "Starting installation ...", and that's it. The computer "thought", I realized that the cursor was spinning (something was loaded), I decided to wait a bit.

About 10 minutes later the window appeared in which I chose clean installation Systems, again waited 5 minutes 5, formatted the section under Windows 7 and went copying files. They copied longer than expected, it seemed to me. In short, I installed Windows 7 with grief in half. Then I realized that there is a long installation of Windows 7 :).

Slowly but established

He worked as a computer as it believes such an iron, it is very easy. It remains only to configure. But I did not have a driver for a modem, so I decided to take the system block to me and pick up the next day.

Search for the reasons for slow installation of Windows 7

At home, I was configured everything, and decided to peel my computer a little more and find out why Windows 7 is installed for so long, I was wondering. Moreover, in the Internet, I did not find a specific answer to this question, only guesses.

Setting the SATA hard disk in bios

To begin with, I opened the system unit and changed connections hard Disc and drive. I connected a hard drive with SATA 0 in SATA 1. And the CD / DVD drive in SATA 3.

Then I climbed into the BIOS. I was interested in settings SATA controller. Section.

On the contrary ONCHIP SATA CONTROLLER Standing Enabled (enabled). Well, then see the item, I have a Native IDE parameter. It is not very good for SATA gesting disk, it will not show all the memories.

Changed the value of the AHCI parameter (the best option for SATA disks). I tried to turn on the computer. The actuator did not determine the campaign at all, but as soon as Windows 7 began to load, then blinking blue screenAnd the computer rebooted.

I decided to install RAID in the parameter instead of AHCI (unites the wheels into an array), nothing happened (I knew what it was useless, but I decided to try), everything is just like with Ahci.

Installed back Native IDE . All these experiments did not help. Although it is very strange why Ahci did not work, I did not understand this.

Turn off DRIVE A.

I also saw that opposite Drive A table option "1.44MB, 3.5". This is the drive, and in this computer it is not. Therefore, I installed "None" to say the system that it is absent.

Saved settings by clicking on F10. Set installation disk With Windows 7 and tried to start the installation to check how the seven will be installed, as slowly or faster.

And on my surprise, everything worked as it should be, a window quickly appeared with a choice of language and so on, I quickly reached the disk formatting. Of course, it did not format, as the computer was already set up, and it had to pick up it.

How to solve the problem of slow installation of Windows 7?

Let's summarize, otherwise I rolled a lot of text :). There was a problem with installing Windows 7, installed for a very long time, and had to wait a lot until the window appears with a choice of language and then long hung "start of installation ...". If you have such a problem, you can just wait and everything will be installed. I installed.

If you want to try to solve this problem, then:

Try in BIOS opposite item to put Ahci (I most likely did not help).
Change SATA connectors for hard disk and drive.
Disable Drive A (drive).

I did the last two items, and installing Windows 7 went fast. I can't say with 100% confidence that it was that it helped to return the normal installation speed of Windows 7. But in any case you need to try.

Sorry what happened so much text, I just wanted to paint everything as much as possible. I hope that my experience was useful to you if it turned out to solve this problem, or some other way, write about it in the comments, it will be interesting and useful. Good luck friends!

Although microsoft. I released and successfully promotes the new versions of the Windows operating system, it is Windows 7 Ultimate that can be considered the most successful and popular among users. Therefore, all problems associated with the installation of the system remain very relevant.
It happens that Windows 7 is not installed or a computer hangs during Windows 7 installation.

Causes of Libid Windows and Winning

If there is a long installation of Windows 7 or the window does not appear initial installationIn most cases it makes sense to change the individual BIOS settings. This is a solid storage device with autonomous nutritionis a set of firmware. Very often when a computer hangs when download windows 7, this is due to incorrect work BIOS.

It often happens that the starting boot window appears 5-10 minutes after the device is circled to boot disk. There are hardware methods that allow you to noticeably speed up the download process.

Windows 7 is loaded long, by different reasonsBut you need to start with BIOS. If Windows 7, then there are many reasons why the computer slowly loads. To speed up the operation of the personal device, you can perform the following actions:

Defragment of a hard disk
Defragmentation and registry cleaner
Removing unnecessary programs
Optimization of the autoload list

Change BIOS settings

Depending on the motherboard and chipset, the entrance to Basic system It is carried out by repeatedly pressing a specific key, immediately after turning on the device. The following keys or combinations are most often used:

Delete.
F1, F2, F3, F10, F11
Ctrl + Alt + ESC
Ctrl + Alt + Ins
Ctrl + Alt + Del

IN modern computers, external drives Connect through the SATA serial interface (Serialata). This standard Supports the function of the command shape and provides for a hot connection of devices. To use all opportunities this interface You must enable AHCI mode. When working S. windows system 7, before turning on this mode to the BIOS, you need to activate the AHCIthere driver to change the registry parameter. The following address is in the following address: HKEY_LOCAL_MACHINE \\ SYSTEM \\ CURRENTCONTROLSET \\ SERVICES \\ MSAHCI is changing the value of the "Start" parameter with 3 or 4 to 0. Then you need to log into the BIOS to perform further actions there.

Fig.1. If the input to BIOS has been successful, the next picture appears on the screen.

Moving the arrows, you need to open the "Integratedperipherals" window. This window has settings of the SATA controller with the ability to change them. The first line indicates that the controller is enabled, this is evidenced by the value "Enabled" - is included.

Fig.2. In the next line, the value "Nativeide" is required to replace on AHCI

In some cases, if the disk is not determined, you can try to set the RAID value (group connection). Then you should turn off the drive on flexible magnetic diskswhich has not been used for a long time and is not part of the peripheral equipment of modern personal devices. This string is as follows: DriveAfloppy 3 Modesupport 1.44M 3.5 ". Next in brackets you need to set the parameter" None ", showing the system about the absence of this device.

Fig.3. As a result, the following

The device is missing and in addition it is turned off. By pressing the F10 key, new settings are saved. Now you need to go to the "Save & ExitSetup" string, which means "Save changes and exit." After rebooting the computer, new parameters will be installed. All, above the listed operations should be performed if the computer is hanging with Windows 7, the laptop hangs when Windows 7 is installed.

If Windows is not installed, then the reason may be infected with viruses. Some software downloaded from the Internet can brake work very much, so when Windows 7 is planned to reinstall the operating system, the device is recommended before starting the process using anti-virus utilities. The new OS should be installed on a computer, fully purified from various "dirt".

More options to do if Windows 7 is freezing

Often, users complain - "I can not". The fact is that many are trying to download a program from the Internet, and this is a very unreliable case because large number viruses on sites with free software. Therefore, it is best to use licensed software on optical disks, or, as a last resort, good pirate copy With an activator. In the process of work, various situations may occur related to a decrease in the speed of the device or with freeing when performing some operations.

If the installation hung windows updates 7, you can wait some time and if after a while installing updates will not continue, then you turn off the power and restart the computer.

It happens when Windows 7 is not installed from the flash drive. The main percentage of failures when installing from a solid-state drive occurs due to incorrect setting BIOS. Elimination of the reasons is indicated above - this is disconnecting the floppy disk and installation aHCI mode. Sometimes the program is not readable because it is recorded incorrectly. To correctly format and write a disk image to a flash drive, you can use a very convenient Ultraiso utility, which supports over 30 formats.

In some cases when unpacking windows files 7 hung on 0%. The main reasons may be two:

Acceleration of the processor with hardware
Many broken sectors on Winchester

In general, when changing frequency to overclock the processor, many software products cease to be installed correctly, but after returning settings to the initial state, the right job is restored. The old hard drive can also be the cause of hang, when installing the operating system. You need to check the hard disk using the Victoria program and, if necessary, replace it with a new drive.

View video

Now you know what to do if the installation of Windows 7 is freezing.

Windows is a mature operating system, and it is usually installed without surprises, but sometimes the installation process freezes.
The following are five ways to solve this problem, topical for Windows XP, Vista and Windows 7.

1. Show patience

The Banal Council, but useful: if the installation hung up, do not hurry to worry. IN lately more than once it was necessary to face the fact that on completely new computers the installation program stops, reaching the screensaver wooden tables. In all cases, the installation resumed by itself - sometimes after 10 minutes, sometimes after 45.

Find the official explanation of Microsoft about the causes of such a hang, while it is impossible. But by observations, it most often happens when installing Windows on computers with Gigabyte motherboards and AMD processors.

Desktop Screensaver is not the only stumbling block for Windows installation program. Sometimes it freezes before displaying a screen with a proposal to select a hard drive to install the operating system. True, in this case, the installation process is renewed much faster.

2. Disconnect the flexible disk controller

Although floppy disks have long come out, some manufacturers still supply their motherboards Controllers of flexible disks. Sometimes Windows cannot be installed until you turn off in bIOS settings Controller diskette.

Unfortunately, this is not a universal recipe, because sometimes installing Windows freezes, even if the controller disks on the motherboard is missing.

3. Check the memory module voltage

If the Windows installation program periodically freezes, it may be caused by non-RAM problems. There are a lot of ways to diagnose problems of this kind. But about one method I would like to say much, because it is often overlooked.

Most motherboards provide for the use of 1.5 V. memory modules if the voltage is higher (even rigid), the system is periodically freezing. However, this does not mean that such memory cannot be used: some motherboards allow you to adjust the voltage of RAM via BIOS.

4. Try to remove or replace memory modules

As mentioned above, most often the installation of Windows freezes due to problems with RAM. In this case, try to remove all memory modules, except for one, and see if the freezing will stop. If it does not help, replace the remaining module to other, verified to eliminate the likelihood of defective memory. If it does not solve the problem, learn the documentation for the motherboard: it is possible that the memory works at unsupported frequency. Even if the module can be installed in the motherboard slot, is not a fact that it will work.

At the same time, check out other requirements for RAM. Some motherboards support only certain brands modules.

5. Try using the IDE or USB DVD drive

Finally, another cause of Windows installation hangs can be a DVD-drive with sATA interface. This does not mean that such drives cannot be used, but the problem is that many motherboards are available for four to six SATA ports designed to create RAID arrays. If you connect to one of these DVD drive ports and try to create a RAID array from fewer hard disksthan provided system boardThe installation of Windows may hang. In this case, it is preferable to use DVD-drive with an IDE or USB interface.

Hello, dear readers.

Sooner or later, all users of computers with operating systems From Microsoft are encountered with a situation where you need to change the medium used. At the same time, the reasons may be very different. Earlier, I already talked exactly how it is necessary to post a new OS on its device. But what if the start of installation of Windows 7 appears, hangs on a laptop and nothing happens? As always, the reasons may be mass. Further in the article I will try to disassemble the most popular of them.

The above problem is manifested in various ways:

The reasons( )

Despite the fact that the process stops at different moments, the reasons are the same:

Problems with hard disk, RAM, power supply.

Insufficient contact with the motherboard.

Circuit of the reader or USB port.

Incorrect BIOS setup.

Error writing an image.

Damage to the data carrier.

Well, as you can see the reasons for the emergence of a problem. Conditionally they are divided into external and internal. Stripping from this, the decision of the ailment will be different.

Waiting for response( )

We will look at everything possible solutions Problems. So, if suddenly on your laptop asus Or any friend suddenly stopped the process of installing the operating system, you should not immediately worry. You may just wait 10 or 15 minutes. It is likely that after that everything will continue without any failures.

Why this is what happens, official sources are not reported.

True, it is worth noting that this in most cases is observed on devices that use maternal gigabyte boards and processors from AMD. Apparently, during their interaction, small failures occur, leading to such consequences.

Distribution( )

What if the past version did not help, and your HP laptop or the other still hangs? It is worth trying to take a new portable memory with distribution of Windows. In addition, you can already have a removable device to test on a computer that differs from yours. If everything happens again - the disease is associated directly with memory. Otherwise, with a computer.

It is worth noting that in the last embodiment, a separate component of the device can be operated incorrectly, with which reading occurs. Therefore for exception possible options It is worth conducting a test, using just a different disk or flash drive.

Bios.( )

On many computers and laptops, regardless of the manufacturer, whether samsung or any other problem with the start of the installation process can be associated with two important parametersthat are exhibited in the field of BIOS:

And for proper work You must specify the appropriate parameters for each. To do this, perform several movements:

Now it is worthy to return to the installation process.

Computer checking( )

If the described methods did not help solve the problem, one of the following steps is to check the computer or lenovo laptop (any other manufacturer) for mechanical damage. Outside it looks like it was before - it is worth promoting the system unit. With a laptop in this case, you need to try a little more.

After opening, we check for the presence of the smell of Gary, drowshes, dark spots. It should be examined by everything that is possible, including the power supply, hard disk, RAM connectors, etc..

As a result, if problem place Detected, it needs to be simply replaced.

Testing RAM and Winchester( )

If the inspection did not lead to anything, it is worth testing important system components. So, MEMTEST is considered to be the most popular program today.