Programmable remote control. It's easier now! How to choose a universal control panel: trained remote controls for various techniques how to recode a remote to another TV

It is one of the best on the world market. Thanks to their accurate automation, life becomes comfortable and comfortable, as well as safer. Came devices are available, no problems arise when installing on any gate, it's not worth changing them that your cash is very saved.

As for climatic conditions, it should be noted that manufacturers responsibly approached this issue. The equipment perfectly withstands frost, wind, heat, dust, rain.

Camel's consoles

Top-432Na is the most popular. Due to the fact that it is two-channel, you can control a separate device, such as open a barrier and gate. Frequency 433, 92 MHz. Made using a constant code technology. Size -32x68x13. Works at a distance of 150 meters.

Programming

1. It is necessary to set the distance not more than 5 mm from each other.

2. Press the two buttons simultaneously on the new console and hold them. The indicator flashes with a high frequency.

3. Let's release the button and click on one one that must be programmed. Now the indicator is burning smoothly, does not blink.

4. Turn on the old key chain quickly the key to overwrite. All this must be done to make the light bulb on the new remote control.

5. If everything is done correctly, then the indicator will flash on the "clean" keychain three times. This suggests that the record is performed successfully, that is, the code is rewritten.

Top-432SA - two-channel, works for two devices. Frequency 433, 92 MHz.

Copy

1. The distance between the keyfobs should be no more than 5mm.

2. On the new press and hold the button to which the record will be made until the indicator lights up with even light.

3. When a button is glowed on a new remote control, you need to click on the other from which the code is rewriting.

4. The console must blunt three times. Everything is done correctly.

Top-434NA is a four-channel key chain with a working frequency of 433, 92 MHz.

Came Top-434NA programming

1. You need to press and hold two buttons simultaneously on a new key chain until blinking is changed.

2. The lamp is burning smoothly. Briefly need to press the button to be written to the code.

3. While the indicator is lit on the first, it is necessary to quickly press the key on the second to overwrite the code.

4. There should be a flashing three-time on a new key chain, which indicates a successful result.

Top-432e - new model Series torus. Works in two TAM encoding systems and Tor, which allows you to work with the consoles on those objects where the encoding TOR and TAM was installed.

Programming with TOP-432NA

1. Preparation for programming. Click and hold the button on the first key chain transmitter that you want to program until the indicator starts flashing. Release them on the new console.

2. Click on the button. There should be an indicator without blinking.

3. For ten seconds you need to drive a key chain to the Top-432Na, on which the light is on. Turn on the button on the wizard one once. The LED blobs three times and will go out, which speaks of successful copying.

Top-432EV - Improved Model Top Series. Contains 4096 code operations. 32x69x11 mm - overall dimensions.

Copying the Came Top-432EV keyfob with TOP-432NA

1. Press, then hold the two upper buttons on the key chain, which must be programmed before the indicator starts blinking quickly. Now you need to release two buttons on the Top-432Na console.

2. You need to click on any key that you will program.

3. The light should burn with even light.

4. For ten seconds, bring the Top-432EV key chain from below and rear to the TOP-432NA, where the indicator is lit, press once working button Top-432na. Remote device Ready to work in the event that the light bulb blobs three times.

Camels are novelties, which are designed to protect the radio control code, illegal copying outsiders. Two-channel and four-channel are available. Rounds with a dynamic code system.

CAME TWIN CONTAMOR PROGRAMMING

1. It is necessary to have an already authorized key chain, which is already entered in the system using the receiver button.

4. For twenty seconds, click on the button of the new key fob once.

5. We are waiting for about twenty seconds until the radio receives from the so-called programming mode.

6. The new code is introduced. This procedure can be done with the following console. But it is very important: one radio receives no more than 25 keyfobs. Also disconnect those receivers that are close to which you do not need to enter a new code.

Came TCH-4024 and TCH-4048 - four-channel and eight-channel transmitters with a frequency of 40 MHz. Touch is a new generation sensor, allows you to manage multiple objects. There is protection against accidental keystrokes.

Copy Camert Touch

1. Press and hold the two upper buttons at the same time while the indicator starts to flash more often.

2. Press the button to be activated. The indicator will light up with smooth light.

3. Apply the working key chain from behind to a new one for ten seconds and click on the (Work) button, hold for a few seconds.

4. The indicator must freeze three times if everything is performed without errors.

Came and -Dvkhanny and four-channel with a dynamic code. Atomo is a comfortable, elegant console that guarantees excellent work to customers. Provides the reliability of the outgoing signal.

CAME ATOMO CONTROL CONTROL

1. Select the zone of excellent reception, not more than five meters.

2. On the running keychain, press and hold the button until the fifteen seconds will burn the indicator smoothly.

3. On the new device to keep the button once about twenty seconds.

4. We are waiting for fifteen seconds and check the work of a new key chain.

NICE.

Engaged in the production of an automated system for gates, barriers and doors. This Italian company occupies a leading position in the world of automation. Nice products reliable, high-quality, time-tested.

The ability to manage all the processes (close the gate, open rolets) by one console, without leaving home.

Nice Flo 1, Flo 2, FLO 4 - Dynamic code. Frequency 433.92 MHz. Response range up to 150 meters. Dimensions 72x40x15. Release single-channel, two-channel, four-channel.

Nice Flor 1S, Flor 2S, Flor 4S. Single-channel, two-channel, four-channel models are available. Radius of action - 150-200 meters.

Nice Flo, Flor Programming

1. Next to be the receiver.

2. The consoles must be sequentially located.

3. Press the button any on the new and hold for about five seconds.

4. Press the button three times the button.

5. Now we press this button once, which has already been pressed first and release.

Nice ON 1, ON 2, ON 4, ON 9- Rests with a dynamic code. Elegant view, small dimensions. Works under all weather conditions. There is a special ring for mounting on the keys. Control frequency 433 MHz.

Nice ON Pattakes Programming

1. The two consoles must come into contact the upper part.

2. Press any button on the new key chain and hold while the light is not lit up on the old one. Let's release the key, and on the second it must turn the indicator.

3. Press any button on the old key chain, hold on the new button until the indicator lights up.

4. Release the button on the old key chain. Forecast indicator in the new is a successful programming.

Nice Very Ve is a two-channel panel with a statistical code.

Nice Very VE Programming

1. Press the two buttons simultaneously until the light is turned on.

2. Press the top key if the first switch on the "ON" position on the receiver. Press the bottom button if the microswitch is in the "OFF" position.

3. Clause number 2 repeat for all ten microswitters that are located on the receiver.

4. The LED will begin to blink quickly if the tenth switch is turned on. While it flashes, if the buttons are not pressed, then the code will be saved in memory.

Nice Very VR-two-channel key chain with floating code. Frequency 433, 92 MHz.

Nice Veri VR CONTOLERIA

1. There must be a remote, which is already recorded in the receiver. There is always a record of the first to the receiver with a floating code using the receiver button.

2. For five minutes we transmit code by holding the key of the new console.

3. Press the button of the old device three times.

4. Briefly press the button of the new console. All recording is completed.

HORMANN - Quality Time Tested

Germany products. Reliability, convenience, beautiful design.

This manufacturer produces consoles with the same design, but with different radio frequencies. They differ in color buttons: blue (868 MHz), green (26, 975 MHz), gray (40 MHz).

HORMANN HSM 4 - four-channel remote control for gates and barriers. Overall size 37x110x13. Frequency 868 MHz. Dynamic code.

HSM 4 console programming

1. Place the head to the head "key rings.

2. Press the button on the old panel and hold. Light bulb should burn constantly.

3. Press the programming key on the new console and retain. The indicator will first flash slowly about four seconds, and then after successful implementation Start flashing faster.

The HSE2 remote control is two-button. Key ring. Frequency 868 MHz.

HORMANN HSM with a frequency of 40,680 MHz. Two-button and four-button.

HORMANN HSM 40 MHz Programming

1. Place new remote Near the old one.

2. Click on the button of the old console and hold.

3. Press the corresponding button on the new console. The LED must blink four times.

4. Release the buttons.

HSP4-C - the remote control for the gate and barriers. New design. Beautiful appearance. Frequency 868 MHz. Dimensions - 48x48x13 mm. The number of buttons is four.

Copying the HSP4-C console

1. Locate key chains next to each other.

2. Press the transmitter key that inherits the code and hold it five seconds. The indicator should burn constantly.

3. Then click on the button that you want to program on a new key chain, hold it. For about four seconds, the light bulb will flash slowly, but after successful task execution - faster.

4. We release the keys on both consoles.

Doorhan.

Doorhan is a major automotive supplier for gates, remotes, radio receivers. Focusing the world market.

Doorhan Transmitter 2, TRANSMITTER 4 - Remote Code Restants. The operating frequency is 433 MHz. Intended for remote control Two and four automatic devices Doorhan, as well as to any other automatic with the available DoorHan radio receiver. One keychain can be controlled by two (four) gates, barriers.

Doorhan programming with DHRE-2 receiver

1. Clean the memory of old codes. After turning on the power, hold the recording button for about 10 seconds. The indicator will flash 10 seconds, then it will go out, then blinks twice. All old codes are removed.

2. To record the console code, click and keep 3 seconds the SW1 key on the receiver board. Then click on the button on the console 2-3 seconds.

3. If the tincture of other consoles is required, then repeat the code record.

You can program a specific control channel by each key.

BFT products guarantees quality and reliability

BFT -12, BFT -12 - two-channel, four-channel consoles. Frequency 433.92 MHz.

Programming CFT remotes

1. Press the "OK" button. A greeting will appear.

2. Click the "OK" button. We see the first section of the "Raareter" menu.

3. Now press the "-" key several times, the Radio menu appears.

4. Press "OK" again and see that the section of the adding chain menu appears in the memory of the AD START radio.

To add brass needs:

1. Press the "OK" button is the inscription "Hidden Button".

2. Press two key fob buttons to write.

3. The "Relise" inscription will appear, and then "Desired Button".

4. Press the remote button.

5. Appear "OK \u200b\u200b1". Everything went successfully.

6. To record other keyfobs, we will do everything by analogy.

7. After the recording of all the remotes is made, press twice the buttons<+> and<-> At the same time.

FAAC - a recognized leader in the manufacture of automatic barriers, gates

The Italian firm is known not only in Europe, but also around the world.

XT2-868 SLH, XT4-868 SLH - two-channel and four-channel remote control for gates and barriers from 868, 35 MHz frequency. Works at temperatures from -20 to +55 C. Radius up to 50 meters.

FAAC DL2 868 SLH, FAAC DL4 868 SLH - outdated models, removed from production. Two-channel and four-channel. The new XT series consoles completely replace the previous ones. They differ only with stylish design, improved characteristics.

Programming the FAAC XT2-868 SLH and XT4-868 SLH series

A master keychain is needed, that is, the one that is recorded first (master), as well as a new remote control (Slave).

1. Press on the old device of the P1 and P2 buttons at once for two seconds. The LED blinked, then you can start programming, as he saw this device.

3. The indicator burns constantly. Click on the old remote key to overwrite.

4. Click on the Slave button for programming. We release the button after the light bulbists twice.

5. All copy is completed. Actions can be done on all other buttons and other consoles.

In conclusion I would like to say that now in our time the automatic control system is installed on all types of barriers, gates, doors. You can control using a separate console, which greatly increases the level of security, especially from theft.

Enjoy auto console - This is a pleasure. The main thing is that you can always carry it with you on a bundle with keys. You can also, for example, in bad weather, without leaving home, use it. Everything can be selected and installed at the request of the client.

Unfortunately, programming remote control (remote control) for gates is not always carried out by uniform methods. The programming algorithm may vary and depends on the manufacturer. To begin, we should register on the receiver control board.

Many manufacturers use code copying method. For example, to configure Faac and NICE. Record one PO in the receiver is required. The remaining consoles are programmed by copying the first keyfoot. The subsequent recording can lead to all the rest. This method is quite convenient, because Does not require a constant recording of each gate control panel separately.

However, the security of such a system is to doubt. Imagine the situation that your remote control of the gate for some time fell into the hands of another person. An attacker will be required no more than a minute to copy the signal to its same. This is necessary to think first. Thus, it becomes clear that the use of such a system for organizations and companies is not the most best idea. Copying the signal will be released from under control.

Alternatives are systems Gant. and. The essence of such systems is the recording of each remote control to the receiver using unique signals. But it is worth noting that such systems have limitations on the number of recorded devices. These systems are considered safer, because It is impossible to copy the signal so easily. For enterprises, this is the best option.

Do not forget, before recording new remote control to erase old data from the receiver. As a rule, deleting all records is made by holding the button on the receiver for 10-15 seconds.

Now we will analyze programming in more detail.

• To begin with, press the "Learn" button on the drive control unit. After a second, the LED should light up for this inscription;
• Then, by clicking the button on the keychain, you will see how the LED flashes and goes out.

Congratulations, you saved the signal! If necessary, with the rest of the consoles, spend the same procedure. This microcircuit can record up to 100 remotes, however, its memory is limited. If you need to remove keychains, you should hold the "Learn" button for no more than 10 seconds.

Came.

• The "Prog" key is located on the control unit. Hold the key before the indicator flashes;
• Next - we press the key on the keychain. Recovering level light means a successful entry.

Unlike the "Professional" system, the recording of subsequent key chains occurs in a different way. Let's make copying.

• Click two buttons on the new remote. In this case, the LED will flash;
• Next, you should release the keys and click the one we must program;
• After the LED signal, bring the programmed key chain to the second and press the working key. The indicator should blink 4 times.

Duplicate console from the gate Came is ready.

To record the remaining devices, you should repeat the action.

Faac

• For recording you need to hold the "P1" and "P2" keys. We release them only after the indicator on the key chain is lit.
• Then the receiver board button is cleaned until the LED signal appears.
• In the process of blinking the indicator on the remote control, press a button that will manage the goal sash. After 3 seconds, let go of the receiver buttons and the remote control.

The signal is recorded!

The FAAC system also uses copying, as in the previous "CAME" system.

• On the programmed key chain, clamp the "P1" and "P2" buttons.
• After the LED signal, the button should be released.
• Both key products are located against each other.
• Next, click the button of the main key fob, with which the signal will be rewritten. After the code is saved, the indicator blinks 2 times.
• For all other devices, the operation will be repeated.

• Within 3 seconds, hold the button on the receiver. The "LED1" indicator will light up, i.e. Record started.
• The button of the console is also held at least 3 seconds.
• The rest are programmed in the same way.

NICE.

Firm "Nice" Works in 2 directions - key rings with dynamic code and with a constant code. They differ in the color of the case. Blue - Permanent, Black - Dynamic.

"Nice" with a constant code is programmed using 2x-range switches. They are present both on the key chain and at the receiver. Such devices of old development are rare today. To prepare another keyfob, the main, already programmed by the remote control, must be promoting and set the switches to exactly the same position. This system implies copying, so consider this procedure Read more.

• To get started, it should be noted that both key products must be in the radius zone of the receiver;
• Hold the desired button new Pow for 5 seconds;
• Button the main thing The PD is pressed 3 times (short pressing).

Everything. The signal is programmed.

To format a receiver memory, hold the button to 3 times the flicker. After the third flicker, the button should be released. If the LED promises five times, it all happened.

Universal remote

Currently, you can buy a special universal programmable console, which is configured to a maximum of 4 frequencies and is suitable immediately for 4 different automatic gates (, lifting-swivel or sliding). We think you should not explain what it is comfortable. The cost of such devices is about 700 rubles.

Finally, see the video instruction on the programming of the new console for the automatic rollback gate of Nice from the old:

Universal gate consoles allow you to simultaneously manage multiple devices. Modern manufacturers offer one device to which multiple keyfobs connect. But sometimes devices are lost or broken, and they must be replaced by new ones. Therefore, owners need to know how to program a remote from the gate.

You can bogranize the console itself

Features of the console

First, the remote must be prescribed on the control board in the receiver. There is no universal device programming algorithm, since the encoding of different companies is different. The most famous manufacturers Removers for the gate:

• Professional;
• FAAC;
• Doorhan;
• Nice;
• Came.

FAAC, Nice and Came companies have one feature: Only one remote can be prescribed in the receiver, and it must be copied from it the necessary number of different keyfobs. If you try to make another device, then the first and all the devices connected to it will stop working. In case of loss of the old console, it is removed automatically when recording a new one. The main advantage of the devices of these companies is the lack of the need to open the electric drive cover when setting up.

But such consoles are very vulnerable - we can sufficiently hold it in the hands of ten seconds in order to distribute the signal to your device.

Each remote has its own programming features

Employees can transmit each other to copy devices, they will appear more than it was issued. If there was limited access to the parking lot, then in this case the places will not be enough due to the easier access to the instrument.

Firms Doorhan and Professional Release systems in which in one receiver can flash each console individually. Among the disadvantages allocate the need to open the drive cover each time before programming, as well as a limit on the number of connected remotes - up to 128 pieces. The device does not allow cloning the instruments.

Professional Programming Programming

To program the remote from the barrier and the Professional gate, it is necessary on the receiver control unit press the "Learn" button And hold it for one second. After that, the LED will light up with an appropriate inscription. Now you need to push the same button on the key chain and wait until the LED flashes on the drive block and goes out. This will mean that the device is saved in the receiver's memory.

In this video you will learn how to program the console:

To connect additional remote controls, the operation is repeated. Memory from the receiver limited: models can memorize from 25 to 128 devices. If you need to delete all the data, the button is clamped to eight seconds. After it goes out, all devices will be deleted. Then you can engage the drive reprogramming.

Came.

Programming camel Came. It occurs according to a similar scheme. First you need to click and hold the Prog button on the receiver. As soon as the LED flashes, the second hand needs to be pressing the corresponding protrusion on the key chain. If the diode lights up with a smooth light, then both buttons need to be released. The remote will be recorded in the drive.

Write the second keychain on the same instruction will not work, as it is in this way you can only recode the receiver. That is, the first device will be shred from the memory, and the new will be recorded in its place. Instead, it is necessary to carry out a copy procedure. On the new device you need to press and detain both buttons, the LED flashing. Then they are released and press the one that allows you to program the receiver, the bulb should burn exactly.

Ten seconds, the first console will be brought to Berechalka, which has already been connected to the drive. It is located behind the connected instrument, click on it the operating button. The diode must be blown three times and ground. This is the programming of the CAME keyfob.

FAAC product

In the receiver, in order to configure the FAAC console, you need to press the two buttons P1 and P 2. They are released at the moment when the LED flashes on the key chain. Then you need to press the button on the drive board until the indicator flashes. While the diode is on, it is necessary to press a button on the control panel, which must be programmed on the goal sash. The code is saved for about two seconds, then you can release all the buttons.

It is necessary to reprogram the remote from the gate differently, since the repetition of past instructions will erase the first key chain and will record a new one. To record multiple consoles you need to stick to a certain algorithm:

• on the keychain recorded in the drive, the P1 and P 2 buttons are clamped, the indicator flashes;
• the new device is located opposite the first;
• on the already programmed instrument, the button is clamped from which the signal will be rewritten;
• you need to wait for a double flashing of the pultard.

So you can record an unlimited number of keyfobs with the same code.

Keychain Nice.

Program the Chinese remote to the Nice gate is needed using two switches on the keychain itself and the radio channel. On the receiver, without delay, press the key, on the key chain, you need to hold 4 seconds and wait for a triple flashing of the indicator. So the device will be recorded, and while it will be in programming mode, you can write a few more.

After the expiration of the Ten seconds, the receiver will remember all key chains and buttons on them. You can program the remote control. To do this, press the key on the new key chain, delay for five seconds and release. The already recorded key clamp three times, then once - on the second instrument. To remove it from the memory of the receiver, you must press the key, wait for the LED signals. The indicator should turn around once, go out and shim off three times. Then there comes a small pause, and the light bulb will promote five times.

Consoles for programming the gate are different, they are different and the connection procedure. Record, recode and delete key rings, you need according to the instructions of each manufacturer.

Manufacturers of technology are trying each device to supply the remote control to the user it is convenient to use their products. No need to rise to turn off the light, customize the operation of the air conditioner, the fan go to turn on / off the TV, everything can be done, sitting on the sofa. This, of course, is convenient, but over time, the coffee tables are clinging to different remuneration, which creates a certain confusion and irritation.

If you do not know that there is a universal console, which can be configured to control several devices at once, then in this article we will tell you about all its capabilities and give instructions, how to use and how to correct it.

If you have become a happy user digital televisionIn your apartment there was a new device with the remote control of the Receiver. And in order not to add another remote control to everyday, let's understand how to use a universal console.

Despite all breakthroughs in technology, the instruments of the remote control have not changed at all. They can have different shapeBut the design of any console still consists of a housing, an electronic circuit, buttons, LEDs, as well as an offline power source.

The universal remote has identical internal organization, Only you can configure to control several devices at once. For example, having bought such a device, you can remove the television, seating and multimedia console into the closet, and all of their functions will register in the universal remote control.

Can any remote control be universal? Not. Although they look like, but internal electronic circuit They have different. Only intended for this instruments can be configured to control multiple devices.

The difference between the original and universal remote control

The remote control from the TV, for example, TV Tricolor, the device itself is useless, it can only be used in a pair with another device - a television, for which it was created.

The principle of operation of the remote control is based on three acts:

• When you press the device button, you are mechanically involved in a chip in which a certain sequence of electrical pulses is created;
• The LED element of the console converts the resulting command to infrared radiation with a wavelength of 0.75-1.4 micron, and sends a signal to a conjugate device;
• The TV has a phototransistor, which detects this IR signal and converts it to its electrical pulse, transmits it to its control unit, making the command you specified.

The communication method used in remote controls is called PCM, or pulsed code modulation. Its feature is that each team is assigned a separate 3-bit sequence, for example:

000 - Turn off the TV;
001 - Select the following channel;
010 - Return the previous channel;
011 - increase the volume;
100 - reduce the volume;
111 - Turn on TV, etc.

That is, when you press the button on the remote control, the electronic circuit includes an IR LED in accordance with the specified template: "111" - on, on, on, with a clear long signal step, for example, 3 milliseconds. If you have chosen the volume control button, which has code 011, then the LED will perform three such actions with a predetermined delay: it turns off, turns on and will turn on again.

On the market you can meet three of different types PO:

• Original;
• Unoriginal;
• Universal.

Original and non-original consoles are control devices created for one particular model. technical devices. The only difference is that the first type produces a native plant-producer, which was assembled and the TV itself, and non-original remote control issues various license companies.

Universal remotes (UPD) are trained control devices that:

• Can be configured;
• Suitable for many models of TVs;
• You can use instead of a lost console for any technical device.

The universal remote can be selected in shape, size, color, design, depending on personal preferences. Inside such an appliance special program and a special base of codes that allow you to determine the signals from almost any TV.

The most common brands of universal remote control are Supra, Huayu and Beeline.

How to find out the TV code

To configure a universal console to your TV, it is advisable to know three- or four-digit code of a specific model. You can find such codes either in the technical passport of the TV, or on the manufacturer's website, or in special. He is called - "Code for setting the console".

But how to configure the remote control, if you could not find the desired code of your model? To do this, in each reply the function is laid automatic setting with software search code. It is enough just to press the desired combination of numbers, after which the auto-generation team will start.

Setting up universal movement

First of all, in the remote control you need to insert power supplies. Some remote controls are sold without battery, so they will have to buy additionally. You can stay on batteries, and you can immediately purchase battery elements. The second option will be more expensive, but they can be checked from the network hundreds of times.

Then turn on the TV with which the UPE will be conjugate. On the console, select the desired mode: TV, DVD, PVR or audio (to configure the TV - button "TV"). Hold the button for 3 seconds to light up the indicator on the front panel of the device.

But the following steps will be different: if you do not know the code code of your TV, then go to the next section of the automatic configuration, and if the code is known, then get acquainted with the manual setting instructions.

Automatic

On the digital panel Upda dial the number "9999", without removing the finger from the "9" key until the TV receiver turns off. After that, the procedure of automatic selection of channels will begin, which can take up to 15 minutes of time.

This method is used if the code for the brand of your device is missing in the list trade brands. However, if the conflict of the control buttons arises (the single button is distributed to several devices), then their fixes will be impossible if the search has been launched throughout the database (combination "9999").

IN different models The combination of buttons can be different, the information is better to look at the package from the remote or in the instructions attached to it.

To configure UPRA SUPRA (Supra), which is most often used to control TM LG, Samsung or Philips TVs, the algorithm will be:

• Turn on the TV;
• Send a remote control on it;
• "POWER" and hold it within 5-6 seconds until the LED lights up;
• Wait until the volume icon appears on the screen. Try changing the sound parameter if the TV responds, it means that the setting has passed successfully.

Upda Huayu is configured by such a scheme:

• Turn on TV;
• On the remote control panel, press the button. "SET", following her button "POWER"and then simultaneously release both buttons;
• Press the key again "POWER";
• Make sure the volume appears on the screen;
• To exit the programming mode 2 times press the key "SET".

There is also a third option of auto-tuning, implemented in some models of universal remotes:

• Turn on the TV show;
• Press the button "TV" And hold it until the LED lights up;
• Press and hold the button "MUTE" to connect search;
• Wait for the process ending and check the work of the console by any command: if the TV reacts, then the remote control is successful.

Manual

For all TVs, there is your conjugation code, and knowing it, you can quickly set up a universal console. Learn the code of your model and spend the following actions:

• Turn on the TV receiving;
• At the UPD clamp the button "POWER" And without releasing it, enter the code of your TV model;
• When the device LED blinks 2 times, release the button "POWER".

• To go to programming mode, simultaneously press two buttons: "POWER" and "set" and wait for permanent luminescence of the PU indicator;
• Enter a four-digit code;
• The indicator must be ground, the output is carried out by the "SET" button.

Upda Beeline

• Turn on TV;
• Press 2 buttons: "C" and "SETUP";
• Wait when initialization is completed and after the right, as the indicator blinks 2 times, the buttons can be released;
• Performance check is carried out with the "VOL" button.

If you do not have time to enter the code for one minute, the TV will be translated into normal mode and the setting will need to start first.

Without code

You can also configure a universal remote to control the TV using code search. To do this, follow these actions:

• Turn on the TV and direct the UPD on it;
• Simultaneously press two buttons: "TV" and Ok. Hold them in an active state of 2-3 seconds until all the PD buttons appear. Wait until only numeric buttons remain;
• Slowly press the channel switch button "Ch +" As long as the TV does not turn off, it will mean that the code is selected;
• To save the settings, click "TV".

Please note that the speed of the selection of code for each television model is different, therefore, by pressing "CH +", expect a couple of seconds to have time to notice the reaction of the television.

Smartphones with a universal console function

Do you know that recent models Some smartphones already have a universal console function? You can not buy another remote control, but simply configure the phone to manage all the devices in your apartment, but only those that have SMART options.

To set up a universal remote on the smartphone, you will have to visit the playmarket and download mobile app. There are many of them, so read the reviews and install the most suitable for you.

After starting the program, you will be offered a list of equipment (TV shows, media streamer, TV, player, smart House etc). Choose what you want to control. Next, you will need to specify the manufacturer and the pairing method (Wi-Fi, Bluetooth, IR port).

The program will launch the search for the equipment, and as soon as you see the name of your technology on the phone screen, choose it. A special confirmation code will appear on the TV display, which will remain in the program on the smartphone. Now you have no phone in your hands, but also a control panel.

This installation is extremely simple and understandable. All instructions sequentially appear on the phone, and you can only confirm your actions. For such a setting, you do not need to know the code and automatic search Also not need. Remote communication is installed on the selected technology. wireless communication from specific devices in your apartment.

Have the only control panel for all equipment in the house - it is very convenient. And as you understood from our article, set up universal remote control just enough and quickly.

Note.