How to program the remote control from the automatic gate. How to program a remote from the gate

Today in the world market there are many manufacturers who are engaged in automation. Its necessary to be able to properly program that the necessary technologies well work well.

Now we will look at the remotes from the gate. If you perform their exact setting, then you will protect yourself from the penetration of intruders and make life much more comfortable. You can also use the keychain not only for the opening of the gate, but also for other devices. Let's look at how to program a remote from the gate.

Camel's consoles

This company occupies leading places for the production of universal remotes. They are withstanding various climatic conditions, and they are easy to program.

TOP-432NA.

Came today is considered the highest quality and reliable. She can find many good consoles. According to consumers, the highest quality model - TOP-432NA. What is it connected with? This remote control is two-channel, which allows you to work immediately with several devices, namely, it is possible to open several devices at once, for example, a gate and barrier. Its frequency is 433.92 MHz. This model is capable of working at a fairly long distance - 140 meters. How to program a remote from the Gate Came?

At the first stage, it is necessary to close the remote control close to the goal.
Next you need to press 2 buttons. Hold them while the light bulb will not flash.
After that, click on any button, you just need to choose which will be used for the gate. If the indicator begins to burn exactly and stop blinking, then you did everything right.
We take the old remote, which went with the gate, and press the button to overwrite the code. It should be remembered that everything needs to be done quickly, while the light is on on the CAME remote control.
When the indicator blinks on the new console several times, the overwriting will end. Now you can use it to work with the gate.

Four-channel TOP-434NA

This remote is similar to the first model. The only difference is the size and number of devices that can be programmed. The frequency remains the same. Top-434NA - remote control. How to program it?

As in the first case, you need to bring the remote control to the goal and click on two keys simultaneously. We are waiting until the LED will begin.
Click one of the buttons to start writing on it.
Next, press the button on a special panel to overwrite the code.
After the indicator will flash 3 times, you can start using this remote. The data was successfully overwritten.

Top-432ee

Recently, a new key chain from the Top - Top-432ee series has appeared. It can allow working with devices to programming various encodings, such as there and torus. To start working with this remote control:

You must click on the new key chain that you want to further use to work with the gate. We are waiting until blinking on the indicator appears, and let go of the button.
Repeat pressing on this button.
After action performed, you need to quickly reduce the old console to the Top-432. Press it a key that allows you to open the gate. When the LED blinks 3 times, you can start using the device for the direct purpose.

TOP-432EV.

This remote is considered an improved version. previous model. It has quite small sizes, which allows you to wear it in your pocket. Also, the TOP-432EV may contain 4096 code operations. How to program this keychain?

As before, we clamp the two keys until you see the light bulb flashes. Next, let go and go to the next action.
Select the button to move the data.
We are waiting a few seconds to a permanent loss of the LED.
Picky new remote To the bottom of another keypad and wait until the overwriting is performed. It usually takes about 10-20 seconds. When the LED blinks 3 times, you can be sure that the recording has been successfully completed.

Came Twin.

Another novelty is the key chain Came Twin. It has one feature - code protection. Sustier people will not be able to just take possession of the code to open your gate. They are also produced in various variations - two and four buttons. Came Twin is capable of working with a dynamic code. How to program a remote from the gate?

First you need to make sure that this key chain can already be used and there is a button for receiving the signal.
Drive the remote as close as possible to the receiver.
Next, we take the old key chain and press the key where the required code is recorded. We are waiting until the LED is lit.
After 10 seconds, press the key, which is on the old panel.
After about 20 seconds, the code recording process will end.

NICE.

The Italian company NICE is located in the top of the production of automated systems for various equipment. Their products are quite high quality and reliable. Of course, they have universal consoles that allow you to manage some processes at the same time. How to program the remotes from the Nice gate?

Nice Flo and Flor

Keychains from NICE are quite simply programmed. All models of the FLO and FLOR line can work with a dynamic code at a frequency of 433.92 MHz. They can work, even if you are at a distance of 140 meters from the required object. The consoles are released with one, two or four keys. Consider on the example how to program the remote from the Nice Flo2R gate.

First you should approach the receiver.
It is necessary to arrange the consoles consistently.
Next, select the key to record the code and click on it.
After 5 seconds, you can click on the button that is used to open the gate on the old panel.
It remains only to repeat the keystroke on the first palette. The button programming is completed.

Hormann.

This is a German firm that makes a bet on quality. Her products are quite reliable and beautiful. The manufacturer stains various buttons in different colors to determine for them certain frequencies (blue - 868 MHz, green - 26,975 MHz, gray - 40 MHz).

HORMANN HSM 4.

This model is equipped with four buttons that allow you to control various equipment. HORMANN HSM 4 has a frequency of 868 MHz and the ability to use dynamic code. You can also note the rather small size of the keyfob. How to program a remote from the gate HORMANN HSM 4?

We place a new panel near the old one.
After that, you must press a key with which reading will be performed. We are waiting until the light bulb will be lit.
Next, you need to click on the key that you need to use later. After 5 seconds, the LED will flash quickly. Code transmission completed.

HORMANN HSE2 and HSM

HSE2 has a two-channel mode of operation, and HSM is two and four-channel modes. It has a small size, which allows you to cling it to the keys. The first model operates at a frequency of 868 MHz, and the second is 40,680 MHz. To program them:

First you need to position the consoles close to each other.
We take the old key chain and click on the key with which you want to read the data.
Next, press the key you select to use in a new console.
It remains only to wait for the flashing LED. We release the keys and we can start using this console.

Doorhan.

Doorhan is a Russian company. She has long been on the world market and supplies high-quality equipment for automating work with goal and radio receivers.

Doorhan Transmitter 2, TRANSMITTER 4

These models work with a dynamic code at a frequency of 433 MHz. As you have already noticed from the name, key rings can work with 2 or 4 various devices. How to program the remote from the doorhan gate?

First you need to delete old records. To do this, press the key with which you can record, and wait. After 15 seconds everything will be deleted.
Next, click on the SW1 button (or any other you want to program) and on the old key chain for writing data. We are waiting for a few seconds.
This is completed on this. You can proceed to use.

Company BFT.

The most common consoles of this company are BFT Mitto 2-12, BFT Mitto 4-12. They are two and four-channel, respectively. Could work at a frequency of 433.92 MHz. How to program the remote from the BFT gate?

To transfer the data, press the OK key.
Next, go to Parameter and click a couple of times on the "-" button.
We repeat pressing OK. After that you will find yourself in the menu where you can add the device.
Click on the AD START key and click on the required button.
Next, we click on the appropriate key in the old key chain and wait until the data is converted.

FAAC

This is a rather popular Italian company. Its products are used in many countries of the world.

FAAC XT2-868 SLH and XT4-868 SLH

These models are used to control two or four devices. XT2-868 SLH and XT4-868 SLH operate with a frequency of 868 and 35 MHz, respectively. They can also be used in various climatic conditions. How to program a remote from the FAAC gate?

First you need to simultaneously press the P1 and P2 buttons to program the keychain.
Next you need to arrange the consoles together.
As soon as the LED starts to burn, you must hold the key on the old device, which will be used in the record.
In the new console, select the Slave button. After 15 seconds, the recording will end. Next, you can start using this console.

Conclusion

Today you can program the considered remotes for many devices. How to program a remote from the gate? As you might notice, this is done quite simple. In many consoles, actions are very similar. So that everything went to successfully, hold the instructions. Console You can choose any firm what you enjoy. Of course, you should choose the desired frequency. It will be important parameter When choosing a remote.

Programming consoles for the gate.CAME, FAAC, NICE, DORHAN, PROFESIONAL, GANT.

First of all, it is necessary to register the remote in the receiver on the control board. All manufacturers of automation for gates different algorithm Programming consoles, so there is no single recipe. Let's focus on the main manufacturers of automation for the gate presented in the Ukrainian market - Professional (Gant), Came, Faac, Doorhan, Nice.

First of all, a small leakage.

In CAME, FAAC, NICE systems, one remote control is written to the drive receiver, and then the required number of other key chains is copied from it. If you try to write the following remote to the receiver - the first remote and all the remotes recorded from it will stop working. In cases where you lost the old remote, it is not necessary to delete it from the memory - it myself will erase when you write a new one in the receiver. A huge advantage of such systems is convenience - there is no need to open the cover of the electric drive every time if it was necessary to write the next remote. But this system is very vulnerable - it is enough for me to hold your remote in the hands of seconds 10, to overeat the signal to your remote. And this opens the gate to almost everyone who kept your remote control (or the console of your employees). Suppose you decided to restrict access to the parking lot, put the barrier and issued a tenant 20 CAME consoles (equal to the number of parking spaces). But after a couple of weeks there is not enough space in the parking lot. Why? Because employees give each other consoles for copying and they appeared several times more than it was issued. And how to do it can be read below.

What is the way out? Install Professional (Gant, China) or Doorhan (Dorhan, Russia) system. The main difference of such systems is that the signal of each remote control is written to the receiver individually. The minus is the limit on the number of recordable consoles in the receiver (depending on the model from 25 to 128 pcs) and the need to open the drive cover or receiver every time to record the next remote control. But such a system will not allow a sidewayl to multiply clones. Recommended for enterprises and parking large quantity users. You can't be infinitely trusting everyone without exception to users to users? The plus is the fact that the consoles of these manufacturers are also cheaper than Italian two or three times.

How to program a remote Professional

How to program cAME console

How to program the FAAC remote

How to program the Doorhan remote

How to program the Nice Remote

How to program a remote Professional 100 UAH

Press the "Learn" button on the drive control unit for the gate for the 1st second, the LEARN LED will light up. Click on the button on the keychain, the LEARN LED on the control unit flashes and goes out. Your keychain is saved.

If you need to record additional consoles, repeat this operation. It should be noted that a limited number of remote controls is recorded in the receiver's memory (depending on the amount of microcircuit's memory, the number of recovered recorded can be from 25 to 128 pcs).

To remove all keychains, you must keep the "Learn" button for 8 seconds. All keychains will be worn out of memory.

How to program the CAME remote 25 euros

You must press and hold the PROG button (CH1) on the control unit. The LED indicator begins to flash (left drawing). Press the desired button on the keychain. The LED lights up with a smooth light, which indicates a successful programming of the control unit (right figure). Release both buttons. The console is recorded.

Press and hold both buttons on the remote control, which must be programmed (new remote) (1). The LED indicator will flash quickly (2). Release the buttons and click on one that you want to program (3). The indicator should light up with even light. Not more than 10 seconds to bring the master - keychain (programmed remote) from the bottom and rear to the programmable (on which the indicator is on) and to press it once working button (four). The LED indicator breaks three times (5) and will go out (6). To program other key chains, repeat operation. In this way automatic system It can be configured to work with any number of key chain transmitters with the same code.

How to program the Panel FAAC 25 euros

To write a remote control FAAC to the drive receiver, you must simultaneously press two P1 and P2 buttons on the control panel and release them when the indicator on the remote control flashes (after 1-2 seconds). Then press and hold the button on the receiver board - the indicator on the board must be filled.

While the remote indicator flashes, you must click on the button control unit, the button that must be programmed to manage the door sash before letting the receiver button, make sure that the diode burned for about 2 seconds (in confirmation that the code is saved). Now let's release the button of the console and receiver. The console is recorded.

But if you wish to record more than one console, do not try to repeat this operation, since the next remote control (new) is recorded in the receiver, and the previous one will delete. It is necessary to carry out an operation to copy the console. How to do it below.

On the main remote control (recorded in the receiver), press and hold two P1 and P2 buttons simultaneously release them when the indicator on the remote control flashes (after 1-2 seconds).

Then place the copied (new) remote control in front of the programmed as shown in the picture above. On the main remote control (while the indicator flashes) Press and hold the button from which you want to rewrite the signal. Now click on the new remote control that the button you want to program. The indicator must flash twice as a sign that the code is saved. We release the button and repeat the operation for other proteins. Thus, the automatic system can be configured to work with any number of key chain transmitters with the same code.

How to program the Doorhan remote

Before programming, it is recommended to clear the receiver's memory from the pale codes recorded earlier. To do this, after turning on the power, hold the recording button pressed 10 seconds. The LED will flash for 10 seconds, then it will go out for 2 seconds and will blink twice again to confirm that the remote codes are erased.

To write a remote control to the receiver, press and hold the remote control button on the radio receiver on 3 seconds - the LED1 indicator on the receiver will light up. After that, press the desired button on the remote control for 2-3 seconds. To configure several remotes, repeat the procedure for other remotes.

How to program the Nice Remote

Nice's consoles meet two types - on a fixed code (blue case) and dynamic code (black housing)

The Nice Flo programming with a constant code is performed using the configuration of the two-position DIP switches, both in the remote control itself and in the radio channel. Be careful - the variations must coincide. If you need an additional console, simply unlock the old programmed FLO remote and install the switches to the same position. These are the elutions of the old sample, today are very rare.

Let us last in more detail on programming the consoles with a dynamic code.

Nice Programming with Dynamic Code

At the receiver, press the key once (delay less than 1 sec.). On the remote control to clamp the key for 3-4 seconds, after which the indicator will flash on the receiver 3 times. This means that the remote is successfully identified and recorded in the receiver. After that, the receiver will be in programming mode for another 10 seconds, during this time,
Necessible, you can record a few more remote controls. After the expiration of time (10 sec.) The receiver will remember all the remote controls and all the buttons on each remote control.

You can also program the remote control can also be remotely, with the help of the previously recorded panel. As a result, the "new" remote control button copies the command from the "old" remote button. ATTENTION! Programming a new console from the old should occur within the receiver action radius

Click the desired button of the new console for 5 sec., Then release, press (without clicking) the button on the old remote control 3 times, on the new remote, press the same button 1 time and release. The console button is written and performs the same commands as the button of the old console.

Remote controls recorded in the receiver's memory, if necessary, can be removed. To do this, it is necessary to carry out the following operations:
Press and hold the button on the receiver, you need to wait until the LED turns 1 time, goes out 1 time, and then flips 3 times, release the button on the third flash of the LED.
If all operations are carried out correctly, then after a small pause, the LED on the receiver will obey 5 times.

Unfortunately, programming consoles remote control (PD) for the gate is not always carried out by uniform methods. The programming algorithm may vary and depends on the manufacturer.
To begin, we should register on the receiver control board. Many manufacturers use code copying method. For example, to configure the FAAC and NICE requires an entry of one PD to receiver. The remaining remotes for the automatic gate are programmed by copying from the first block. The subsequent recording can lead to all the rest. This method is quite convenient, because Does not require a permanent record of each gate control panel separately ...
However, the security of such a system is to doubt. Imagine the situation that your remote control of the gate for some time fell into the hands of another person. An attacker will be required no more than a minute to copy the signal to its same. This is necessary to think first. Thus, it becomes clear that the use of such a system for organizations and companies is not the most best idea. Copying the signal will be released from under control.
Alternatives are Gant and Doorhan systems. The essence of such systems is the recording of each remote control to the receiver using unique signals. But it is worth noting that such systems have limitations on the number of recorded devices. These systems are considered safer, because It is impossible to copy the signal so easily. For enterprises, this is the best option.

Do not forget, before recording new remote control to erase old data from the receiver. As a rule, deleting all records is made by holding the button on the receiver for 10-15 seconds.

Now about programming the consoles in more detail.

To begin with, press the "Learn" button on the drive control unit.
After a second, the LED should light up for this inscription;
Then, by clicking the button on the keychain, you will see how the LED flashes and goes out.

Congratulations, you saved the signal! If necessary, with the rest of the consoles, spend the same procedure. This microcircuit can record up to 100 remotes, however, its memory is limited. If you need to remove keychains, you should hold the "Learn" button for no more than 10 seconds.

Came.

The "Prog" key is located on the control unit.
Hold the key before the indicator flashes;

Click two buttons on the new remote. In this case, the LED will flash;
Next, you should release the keys and click the one we must program;
After the LED signal, bring the programmed key chain to the second and press the working key. The indicator should blink 4 times.

Duplicate console from the gate Came Ready.
To record the remaining devices, you should repeat the action.

Faac

For recording you need to hold the "P1" and "P2" keys. We let them go only after the indicator on the key chain is lit;
The receiver board button is then clamped until the LED signal appears;
In the process of blinking the indicator on the remote control, press a button that will manage the goal sash. After 3 seconds, let go of the receiver buttons and the remote control.

The signal is recorded!

The FAAC system also uses copying, as in the previous "CAME" system.

On the programmed key chain, clamp the "P1" and "P2" buttons.
After the LED signal, the button should be released.
Both key products are located against each other.
Next, click the button of the main key fob, with which the signal will be rewritten. After the code is saved, the indicator blinks 2 times.

For all other devices, the operation will be repeated.

Within 3 seconds, hold the button on the receiver. The "LED1" indicator will light up, i.e. recording started;
The button of the console is also held at least 3 seconds.

The rest are programmed in the same way.

NICE.

NICE operates in 2 directions - key chains with a dynamic code and with a constant code. They differ in the color of the case. Blue - permanent, black - dynamic.

"Nice" with a constant code is programmed using 2x-range switches. They are present both on the key chain and at the receiver. Such devices of old development are rare today. To prepare another keyfob, the main, already programmed by the remote control, must be promoting and set the switches to exactly the same position. This system implies copying, so consider this procedure Read more.

To get started, it should be noted that both key products must be in the radius zone of the receiver;
Hold the desired button of the new remote control for 5 seconds;
The main PD button is pressed 3 times (short pressing).

Everything. The signal is programmed.

Universal remote

Currently, you can buy a special universal programmable console, which is adjusted to a maximum of 4 frequencies and suits immediately for 4 different automatic gates (sectional, lifting-swivel or roll-out). We think you should not explain what it is comfortable. The cost of such devices from about 700 - 1300 rubles.

Consoles for gates and barriers are the most convenient devices for automatic control of barriers. They differ in the radio signal frequency and encoding, modulation and other parameters. In order for a model of one manufacturer to open a barrier of another brand, all parameters must match. There is no single apparatus for opening a barrier. Create universal devices capable of opening the fences of those producers who are made to the database. In the previous, we talked about universal key chains for barriers, now consider them more detailed.

Advantages of universal brass

support programming 4-30 devices;
manage multiple mechanisms on the automation of one manufacturer;
work on several modes;
simple in the setup, compact;
compatible models support multiple frequency ranges.

Principle of operation

The console for the fence of a particular brand works only on one specific frequency. A universal compatible device supports multiple frequencies at the same time. It programms several codes of various manufacturers, so such devices are suitable for managing several types of equipment. In the instructions for the product, it can be controlled by what devices and models of barriers can control. Universal panels for barriers can also be configured to control other devices, such as intercom.

Universal panels for barriers and gates

The new universal panel for the barrier must be programmed correctly. The universal product is different from compatible in that programming is possible only at one frequency, you can write only one type of encoding. Only in this case it will work adequately. To configure the operation of each button, the encoding from the original is recorded on it. The control system allows you to "remember" various programmed signals. The type of signal and frequency must necessarily coincide.

The fence receiver receives a signal from a multifunctional remote. The unique signal is checked with the base. When the data is coincided, the barrier opens and then closes in its original position. Special filters support the desired frequency without change, so that external factors do not affect the operation of the device, for example. The universal panel for barriers is suitable for control to 10 standard keychains.

Transfer software code from one device compatible universal device And the changes is possible only for the first 5 seconds after turning on the new console. Initially, the desired button is clamped on a new device before receiving the beep. Then you need to take an old device from the fence and click on it, keeping the appearance of two short sound signals And let it go. Then, to transfer the program code, click the button on the old device several times:

one - step-by-step mode;
two - the rise of the mechanism;
three - lowering the bar;
four - stop.

Manual for programming the console usually included

After pressing, sound signals should be sounded in the quantity that corresponds to the programmable management command. After about 2 seconds, you need to confirm the programmed command by clicking the button again until the first signal appears. With successful programming, three signals should be sounded.

To make a new device in the control unit, you must first at the new, then press the button on the old console, while holding 3 seconds. Then confirm the operation on a new device while holding the button 3 seconds. There will be 3 signals that promote the successful completion of the operation.

On the universal devices With light indicators, for example, Came Top, instead of sound signals use light. Only one instance is programmed to a new console, and the parameters are adjusted. As a rule, two buttons are pressed, which must be programmed on the old apparatus before flashing.

Then press one button on it until the smooth luminescence appears and bring to a new device and click on it the operating button. The indicator should notify the successful end of the flash operation. In this way, work is configured different models To control on one multifunction machine with one code.

Types of universal brass

Take the Multi Universal Consample for the example 4. The remote control can store 4 keys data operating in the frequency range of 315-868.3 MHz. These are CAME, NICE, HORMANN, MARANTEC, DITEC, FACC, MAROG, Marantec, Ditec, Facc, Marantec, Ditec, Hormann, Marantec, Ditec, Facc.

The BRO console models are two-, three and four-channel. Work on a 12B battery, have a light indication. Used in the range of 433 MHz using a dynamic code, have a high range. Cost from 1000 rubles.

The APOLLO Remote Rate is designed for automation consoles with various codes, is able to replace up to 4 copies. Suitable for gates and barriers. There is a model within 750-1200 rubles.

Jolly Open models operate at 433 MHz. Sustainable mechanical shocks, equipped with a movable keyboard. Remembers up to four copies. The cost is 600-700 rubles.

Tech - two- and three-channel apparatus operating at a frequency of 433 MHz. Equipped with light indication. Compatible with Beninca models. It costs from 540 rubles.

DITEC GOL4 C and TRANSMITER - Universal devices suitable for managing any devices on the Doorhan automation. Have 4 independent channels and floating code with 16 million combinations. Cost from 750 rubles.

TX2 / 4 consoles support combination with any models on the FAAC automation. Support two modes of operation: Master and Slave. For programming multiple instruments, only Master is used. There is a model from 1200 rubles.

One-, two- and four-channel channel Intro supports programming up to 30 remote controls on the Radio series. Can manage barriers, rollers, lighting and gates. Cost from 1200 rubles.

Unfortunately, programming remote control (remote control) for gates is not always carried out by uniform methods. The programming algorithm may vary and depends on the manufacturer. To begin, we should register on the receiver control board.

Many manufacturers use code copying method. For example, to configure Faac and NICE. Record one PO in the receiver is required. The remaining consoles are programmed by copying the first keyfoot. The subsequent recording can lead to all the rest. This method is quite convenient, because Does not require a constant recording of each gate control panel separately.

However, the security of such a system is to doubt. Imagine the situation that your remote control of the gate for some time fell into the hands of another person. An attacker will be required no more than a minute to copy the signal to its same. This is necessary to think first. Thus, it becomes clear that the use of such a system for organizations and companies is not the best idea. Copying the signal will be released from under control.

Alternatives are systems Gant. and. The essence of such systems is the recording of each remote control to the receiver using unique signals. But it is worth noting that such systems have limitations on the number of recorded devices. These systems are considered safer, because It is impossible to copy the signal so easily. For enterprises, this is the best option.

Do not forget, before recording new remote control to erase old data from the receiver. As a rule, deleting all records is made by holding the button on the receiver for 10-15 seconds.

Now we will analyze programming in more detail.

To begin with, press the "Learn" button on the drive control unit. After a second, the LED should light up for this inscription;
Then, by clicking the button on the keychain, you will see how the LED flashes and goes out.

Came.

The "Prog" key is located on the control unit. Hold the key before the indicator flashes;
Next - we press the key on the keychain. Recovering level light means a successful entry.

Unlike the "Professional" system, the recording of subsequent key chains occurs in a different way. Let's make copying.

Click two buttons on the new remote. In this case, the LED will flash;
Next, you should release the keys and click the one we must program;
After the LED signal, bring the programmed key chain to the second and press the working key. The indicator should blink 4 times.

Duplicate console from the gate Came is ready.

To record the remaining devices, you should repeat the action.

Faac

For recording you need to hold the "P1" and "P2" keys. We release them only after the indicator on the key chain is lit.
Then the receiver board button is cleaned until the LED signal appears.
In the process of blinking the indicator on the remote control, press a button that will manage the goal sash. After 3 seconds, let go of the receiver buttons and the remote control.

The signal is recorded!

The FAAC system also uses copying, as in the previous "CAME" system.

On the programmed key chain, clamp the "P1" and "P2" buttons.
After the LED signal, the button should be released.
Both key products are located against each other.
Next, click the button of the main key fob, with which the signal will be rewritten. After the code is saved, the indicator blinks 2 times.
For all other devices, the operation will be repeated.

Within 3 seconds, hold the button on the receiver. The "LED1" indicator will light up, i.e. Record started.
The button of the console is also held at least 3 seconds.
The rest are programmed in the same way.

NICE.

Firm "Nice" Works in 2 directions - key rings with dynamic code and with a constant code. They differ in the color of the case. Blue - Permanent, Black - Dynamic.

To get started, it should be noted that both key products must be in the radius zone of the receiver;
Hold the desired button new Pow for 5 seconds;
Button the main thing The PD is pressed 3 times (short pressing).

Everything. The signal is programmed.

To format a receiver memory, hold the button to 3 times the flicker. After the third flicker, the button should be released. If the LED promises five times, it all happened.

Universal remote

Currently, you can buy a special universal programmable console, which is configured to a maximum of 4 frequencies and is suitable immediately for 4 different automatic gates (, lifting-swivel or sliding). We think you should not explain what it is comfortable. The cost of such devices is about 700 rubles.

Finally, see the video instruction on the programming of the new console for the automatic rollback gate of Nice from the old: