How to return the former firmware GS B520. New software versions for GS B520 receivers, GS B521, GS B522, GS B531M, GS B532M, GS B533M, GS E521L and GS C592. Update on the prefix

ATTENTION! Update software occurs in two stages. In no case do not turn off the receiving the receiver until the update procedure is completed! Otherwise, a receiver output is possible!

If you are using the server-client system, you first need to update the C592 client receiver, and then start updating the server receiver.

To update, you must perform the following steps:

1. Remove the power cord of the receiver from the outlet, and then re-enable the receiver to the network.

2. Switch the receiver on the TV channel at number 333 in the overall list.

3. After a few seconds, a message appears on the screen. software next species:

After this message appears, select OK to start updating.

4. Strengthening.

After the consent to the update on the screen there will be service messages about the update process. A reservation update takes about ten minutes, a module update is about five minutes.

Attention! Update by the Customer Receiver GS C592. It may take up to twenty five minutes.

5. Upon completion of the update, the receiver will reboot and turn on with the new version of the software.

ATTENTION! For the GS C592 model receiver, this update is completed, since it does not require a module update.

6. For other models: After turning on the receiver, re-switch it to the channel 333 in the overall list. Within one minute, the screen will appear on the need to update the module.

7. When a message appears on the need to update the module, follow the steps 3-5 of this instruction.

At the end of the update, make sure that the update has passed successfully. To do this, go to the application " Personal Area"(" Menu "-\u003e" Personal Account ") and check the values \u200b\u200bin the" Receiver Version "and" Module version "lines. The update was successful if the following data are displayed:

Third Row: Receiver version - 3.19.171.

Fourth line: module version - 0.0.167.

The figure below shows the view of the application "Personal Account" on the example of the GS B531m receiver after the update:

By module 0.0.167

ATTENTION!

In no case are not turned off the power receiver until the update procedure is completed! Otherwise, a receiver is out of order possible!

Return previous version According to it will be impossible!

Update via USB drive (USB flash drive)

If your receiver is not connected to the satellite plate, then you can update the software via a USB drive. Before downloading on the USB flash drive, it must be formatted in FAT32. In downloaded files you will also find and detailed instructions Installation.

Update through the satellite step by step

To update software through the satellite, the receiver must be connected to a configured satellite plate.

The software update consists of two components: update the main on the receiver and the module.

ATTENTION! If you use the receiver of the GS C592 receiver with the Server receiver, you need to update the software receiver before updating the Server receiver software.

PROCEDURE:

1. Cut the power cord of the receiver's power outlet, and then re-enable the receiver to the network.

2. Switch the receiver to the channel at number 333 in the overall list.

3. After a few seconds, a message appears on the screen to update the following type:

After this message appears, select OK to start updating.

4. Strengthening.

After the conversion on the Receiver Update on the screen there will be service messages about the update process. Update on the GS C592 receiver can take up to twenty-five minutes.

5. Upon completion of the update, the receiver will reboot and turn on with the new version of the software.

ATTENTION! For the GS C592 model receiver, this update is completed, since it does not require a module update.

6. For other models: After turning on the receiver, re-switch it to the channel 333 in the overall list. Within one minute, the screen will appear on the need to update the following type of module:

7. After this message appears, select "OK" to start updating. The update on the module takes about five minutes.

8. After completing the update by the module, the receiver will automatically reboot.

At the end of the update, make sure that the update has passed successfully.
To do this, go to the "Personal Account" application ("Menu" -\u003e "Personal Cabinet") and check the values \u200b\u200bin the "Version Version" and "module version" lines.
The update was successful if the following data are displayed:

Receiver version - 3.19.171
Module version - 0.0.167

This update on the receiver and the module is completed, and the receiver is ready for further work.

Instructions for updating the receivers via the Internet

Before starting the update, make sure your receiver is connected to the Internet.

To do this, connect the Internet cable to the appropriate receiver connector (Ethernet).

If the model of your receiver has developed more a new version Software (software), on the TV screen on any viewed TV channel a message will be displayed with the proposal to update the software *. Confirm the start of the update and wait for it.

Please note: the software version number may differ depending on the equipment model.

During updating on the screen, information will be displayed: "Attention! Do not turn off the power receiver during the update. " Disable equipment from the network can lead to a failure in its work.

The software update takes an average of about 5 minutes, the duration depends on the speed of the Internet connection.

After the update is installed, the receiver will reboot

Note: If the module update is also available for your receiver, a request may appear on the TV screen to hold the update to be confirmed. Upon completion of the update on the module, the receiver will reboot again, after which it will be ready for further work.

Note: The version number of the module may differ depending on the equipment model.

How to update the list of tricolor channels on GS B520 receivers GS B522, GS B521, GS E521L, GS B531M, GS B532M, GS B521H, GS B521HL, GS B531N, GS B534M

To find new channels, do the following.

Update software for satellite receiver GS B520 Ver. 3.9.325, GS1 Ver. 0.0.106. Pow

In the new release of the GS B520 satellite receiver software, additional functionality and improved earlier services:

2. Improved stability;

3. Fixed bugs.

Update software for satellite receiver GS B521 Ver. 3.9.325, GS1 Ver. 0.0.106. Download