You do not work USB wines 7. USB mouse stopped working after downloading Windows? There is a solution. Drivers are set, the drive is displayed. However, the master does not see or does not allow you to choose the desired section

Oh, these computers are always exiting what to do. Even during the time when instead of the Internet were BBS (Bulletin Board System), replacing the current chats, social networks And File Lumps, I said that the computer can be given all the time you have. And now, with the widespread dominance of the Internet, this topic is even more relevant. And it's still surprising how some seemingly elementary things, if you call the computer to help, do not take at all elementary time. It was a surcharge. And a fairy tale ahead.

Let's start from afar. As you all know, a computer without input devices, such as a keyboard and a mouse, may be touchscreen (and some also a joystick) is a simple piece of iron that buzzes and consumes electricity. I got to me the computer that it was necessary to look and reanimately reanimate, after the virus came out there. I pulled out a spare monitor from the shelf, connected the spare keyboard, the USB spare mouse (this is important), turned on, climbed bIOS settings (basic system I / O), downloaded Windows and Owl, the mouse is turned off. Just worked in Bios, the pointer ran lively so, and after windows downloads does not work. What the heck?

We know that there are at least two common types of mice (computer), differing in the connector connector. This is PS / 2 and USB. If the first option is used primarily on stationary computers, the second can be used everywhere, even connect to modern smartphones. And what is important oh, USB connector can be turned on and off in hot mode, i.e. With the computer enabled, but if you have a PS / 2 connector, it is better not to risk, because it can just burn. It is better to turn off the computer, and then connect and disable the details. In old computers there were two PS / 2 connections differently in color. Green - for mouse and purple for keyboard. Now can only be one, or even none.

Let's go back to my computer. The symptoms are as follows: the mouse is completely good, it works until the operating system does not boot, all the time works on another computer, i.e. Business in Windows. USB port It also works, they could connect the keyboard or flash drive to it, then everything is fine. Other USB mouse also does not work. But the PS / 2 mouse is perfectly functioning. When connected to another USB connector, the system writes that the device is found, the driver is installed, the driver is installed successfully, but the mouse also does not work.

We look at the device through device manager. In it, we are interested in mice and other indicating devices. If in the tab we do not see our mouse, then the problem with the driver *. And one more problem is that the USB mice are so standard that special driver I do not need and already exist in the list of standard. We connect the mouse, we see that something new appeared in the section HID devices, therefore the mouse is recognized not as a mouse, but as something else. At the same time, at all the same in which USB port turn on the mouse. It will not work. To correct the situation, you must manually change the driver on the HID device. From the context menu HID device to select Refresh Drivers-\u003e Search and Install Driver Drivers-\u003e Select from installed drivers-\u003e HID Compatible Mouse

After that, the USB mouse appears in the mouse list and starts working. Even after disconnecting and rebooting the computer.

* Driver is a program that allows you to directly control the device in the operating system. Since the operating system does not know the variety of devices, then for full-fledged work, devices manufacturers produce a driver that becomes an intermediate layer between the device and operating system. If the device is standard, the special driver is not needed, it is already included in the operating system.

Greetings to all!

Not so long ago I watched a very busy picture (even funny) picture: at work one guy, when the mouse stopped working, stood and did not know what to do - I didn't even know how to turn off the PC ... Meanwhile, I will tell you, many actions that Users are made using a mouse - you can easily and quickly perform using the keyboard. I will even say more - the speed of work rises at times!

The mouse, by the way, I repaired him quite quickly - so, in fact, the topic of this article was born. Here I want to bring some tips that you can try to do to restore the mouse ...

By the way, I will assume that your mouse does not work at all - i.e. Do not even move the pointer. Thus, I will bring the buttons in each step to click on the keyboard to perform this or that action.

Problem number 1 - Mouse pointer does not move at all

This is the worst, probably that could happen. Since some users simply did not prepare for it at all :). Many do not even know how in this case go to the control panel, or run a film, music. We will understand in order.

1. Check the wires and connectors

The first to recommend to do is check the wires and connectors. Wires are often overloaded with pets (cats, for example, love to do it), accidentally bend, etc. Many mice when connecting them to the computer, begin to glow (the LED is lit inside). Pay attention to it.

Also check the USB port. After the wires corrected, try to restart the computer. By the way, on some PCs there are ports on the front side system Block And on the back - try the mouse to connect to other USB ports.

In general, the basic truths that many neglect ...

2. Check batteries

It refers to wireless mice. Try, or change the battery, or charge it, then check again.

3. Troubleshooting the mouse over the master embedded in Windows

Windows has a special master, which is just designed to search and automatically eliminate a variety of problems with the mouse. If the mouse is on the LED, after it is connected to the PC, and it still does not work - then you need to try using this tool in Windows (before buying a new mouse :)).

1) First open the string to execute: click simultaneously buttons Win + R. (or button WIN.If you have Windows 7).

2) In the Row, write to the command Control and click ENTER.

3) Next click several times the button Tab. (Left keyboard, next to Caps Lock. ). You can help yourself arrows . The task here is simple: you need to highlight the section " Equipment and sound ". The screen below shows how the selected section looks like. After selecting - just press the key ENTER (Thus, this section will open).

Control panel - equipment and sound.

5) Next with the help of buttons Tab and arrows Highlight the mouse, and then press the button combination SHIFT + F10. . Then you should appear the properties window in which there will be a cherished tab " Troubleshooting "(See Screenshot below). Actually, open it!

To open the same menu: Highlight the mouse (Tab button), then press the Shift + F10 buttons.

By the way, after checking, no instructions may not be for you, and your problem will be eliminated. Therefore, at the end of the check, click Finish and restart the PC. Perhaps after rebooting everything will work ...

4. Verification and driver update

It happens that Windows incorrectly defines the mouse and installs "not the driver" (Or simply there was a conflict of drivers. By the way, before the mouse stopped working, you did not install any equipment? Perhaps the answer do you already know?!) .

To determine whether everything is in order with the driver, you must open device Manager .

1) Press buttons Win + R. then enter the command devmgmt.msc. (Screenshot below) and click on ENTER.

2) must open "device Manager" . Please note whether there are yellow exclamation marks, opposite the various kinds of equipment (especially opposite the mouse).

3) To update Driver: just with help arrows and Tab buttons Highlight your device, then press the buttons. SHIFT + F10. - And select "Update Drivers" (Screen below).

4) Next choose automatic update And wait until Windows checks and installs drivers. By the way, if the update does not help - try removing the device (and the driver with it), and then install it again.

Maybe my article with best programs For auto-update:

5. Mouse checking on another PC, laptop

The last thing I would recommend similar problem - It is to check the mouse on another PC, laptop. If she does not work there - the high probability that she came to the end. No, you can try it to climb with a soldering iron, but what is called " sheepskin - Do not stand«.

Problem number 2 - the mouse pointer hangs, moves quickly or slowly, jerks

It happens that for a time the mouse pointer, as it is freezing, and then continues to move (sometimes just moving jerks). This may occur for several reasons:

: In this case, as a rule, the computer slows down in general in general, many applications do not open, etc. How to deal with the download of the CPU I described in this article :;
system interrupts "Work", violating the stability of the PC (about this, as well as on the link above);
hard disk problems, CD / DVD disk - The computer can not consider the data (I think many noticed this, especially when you take a problematic carrier - and PC, as it disperses). I think many will be useful to the reference to the status of his hard disk: ;
some types of mice "Require" special settings: for example, a game computer mouse http://price.ua/logitech/logitech_mx_master/catc288m1132289.html - may behave unstable, if not removed the tick with increased point accuracy. In addition, it may be necessary to install utilities that run on the disk complete to the mouse (it is better to install them all if problems are observed) . I also recommend entering the mouse settings and check all the checkboxes.

How to check the mouse settings?

Open control Panel, Next, go to the section " Equipment and sound". Then open the "Mouse" section (Scrong below).

the speed of the pointer: Try to change it, often too fast mouse movement affects its accuracy;
increased pointer installation accuracy: Put or remove the checkbox opposite this item and check the mouse. Sometimes, this checkbox is a stumbling block;
display a mouse pointer track: If you enable this checkbox, you will observe how the trail remains on the screen from moving the mouse. On the one hand, some users will even conveniently (for example, the pointer can be fastened faster, or if you shoot for someone video from the screen - show how the pointer moves) On the other hand, many of this setting are considered for the "brakes" of the mouse. In general, try switch on switch off.

Mouse Adapter: USB-\u003e PS / 2

Problem number 3 - a double (triple) click (or 1 button does not work)

This problem, most often, appears at the old mouse, which has already been pretty worked. And most often, I have to notice, it takes place with the left mouse button - as the entire main load (even in games, at least when working in Windows) is located on it.

By the way, my blog has already had a note on this topic in which I advised how easy you can get rid of this ailment. It was about O. simple way: Change places left and right buttons at the mouse. It is done quickly, especially if you have ever kept a soldering iron in your hands.

Replacing the right on the left mouse button.

If you did not hold - two options: ask a neighbor or a friend who is about it about it; Or go to the store for a new ...

By the way, as well as an option, you can disassemble the mouse button, then get a copper plate, clean it and adjust. This is described in detail here (though, an article in English, but everything is clear according to the pictures): http://www.overclockers.com/mouse-clicking-troubles-diy-repair/

PS.

By the way, if you periodically turn on and turns off the mouse (that, too, by the way, not uncommon) - 99% the problem in the wire, which periodically moves away and the connection is lost. Try to fix it with scotch (for example) - thus the mouse will last you have not yet one year.

You can also climb a soldering iron, pre-cut off 5-10 cm. Wires in the "desired" place (where the beggar happened), but I will not advise it, as for many users - this procedure is more difficult than going to the store for the new mouse ...

FROM oveter for a new mouse. E.if you are a fan of new-fashioned shooters, strategies, action - you would fit some modern game Mouse . The extra buttons on the mouse housing will help increase micro controls in the game and distribute commands more effectively and manage your characters. In addition, if one button "flies" - you can always shift the function of one button to another (i.e., reassign the button (wrote above in the article above)).

Installing Windows 7 is a simple and debugged, but not the perfect process. Therefore, there may be situations where the installation wizard simply sees certain computer devices without giving the user to complete the procedure started normally. And if you have such difficulties - familiarize yourself with the content.

Windows 7 installation does not see the USB mouse and keyboard (solve the BIOS settings problem)

If Windows 7 installation does not see the mouse or another input device, the first thing to do is check it USB portsIn which these peripheral devices are inserted.

Blue ports (USB 3.0) can do not support Master, and therefore, at least at the installation time, rearrange the equipment in the ports of gray ( USB 2.0 ).

In most cases, the problem will be solved. Otherwise, do the following in order actions B.Bios. (hereinafter referred to as the article, these actions will be painted with step by step):

Disable(I.nTEL.) "Xhci. Mode. » In the tab « Advanced » ;
Try another value of the point "USB Legacy Support" ;
Reset BIOS.

Do at once all three actions optional.
Check the operation of the mouse and keyboard after each step, starting from the first. First you need to go to the BIOS. Read more, how to enter BIOS on the various devices (Stationary computers or on different laptop brands) you can see this article: how to enter BIOS. Restart your computer and logo motherboard Enter B. « Setup. Menu. » by pressing the key F.1 (F.2, F.12, Delete. - Depending on the BIOS). Now proceed:

Action 1 - Turn off (Intel) XHCI Mode

This option you can find in the tab « Advanced » on the menu Bios..

Go to B. « Advanced » , by navigating the arroders on the keyboard;
Change the regime on « Disabled. » in point « xhci. Mode. » ;

Figure 1. Install the Disabled mode for XHCI Mode.

Save settings by going to the tab « EXIT » and choosing " EXIT Saving. Changes »;
We check the mouse and the keyboard, repeating the attempt to install the OS.

The first action helps in the absolute majority of cases. Go to the next header if:

Line « xhci. Mode. » absent;
Performing item « Action 1.» did not give the result.

Step 2 - Switch USB Legacy Support Mode

Unlike described above, the option « USB Legacy Support » Affordable to edit on the absolute majority of systems.

It is also predominantly in the tab. « Advanced » . We need to change the mode of this function to the opposite ( "Enabled" on the « Disabled " or vice versa).

Figure 2. Change the value of USB Legacy Support.
Do not forget save changein the tab « EXIT » By selecting the option " EXIT Saving. Changes "The computer will restart automatically.

Check our devices by running the Windows installation again. If the peripherals still does not work, you should try reset the motherboard settings.

Action 3 - Reset BIOS (if previous actions do not help)

To return the BIOS to the "factory" settings, you need:

Go to the tab « EXIT » (usually follows after Boot);
Select item " Load. Setup. Optimal) Defaults. »→ Confirm the action by pressing" Yes " The computer will reboot.

These steps with a big chance will help solve your problem with a USB mouse and keyboard. Otherwise, check the periphery for hardware failures on another computer. Also try connecting other devices.

Solving the problem when using PS / 2 keyboard and mouse

Failures in these devices occur quite rarely and are mainly associated with BIOS and hardware failures. Before performing the following actions beforedisconnect the power of the computer. Such a precaution is related to the fact that ports PS./2 It is extremely recommended to touch with a working system. If you use standard PS./2 Peripheral, follows:

Check and clean the connector / keyboard port and mouse from of various types pollution;
Try a similar USB equipment;
Change the mouse and keyboard connectors in places;
Refresh Bios maternal Boards to the latest version.

If all of the above does not help, try using other copy Windows 7. Lack of support PS./2 Devices may be related to the fact that the specific assembly does not contain, in fact, outdated drivers for these devices (can be cut from the final image).

The computer does not see the boot flash drive and / or other USB devices when installing Windows 7

The solution of such a problem in most cases is sufficient. And before starting to delve into this chapter, you must follow these steps: If installingWindows does not seeUSB Devices at all, refer. It presents some general, decisive the most common failures.

Windows 7 installation wizard sees hard disk (SSD) or asks the driver

Before starting the actions that affect the program part, you need to make sure that the drives and the correctness of the computer settings are performed. Note. Next actions are relevant forSSD.. If in the disk selection window for installation absent The desired "Winchester" (hard disk), try first:

Checkloops and attachments HDD / SSD;
Disableextra drives, leaving only the one to which the installation of the OS will be carried out;
Switchmode « SATA. Mode. » from « Ahci. » on the « IDE » (any other available);

We will analyze morethe thirdparagraph. For this you need:

Turn off computer;
Log in BIOS (or « Setup. Menu. » ) by clicking the button F.1 (F2, F12, DELETE) Immediately after turning on the computer at the stage when the manufacturer's logo of your motherboard is displayed on the screen;
Driving arrows, find on the item item « Configure. SATA. as » or « SATA. Configuration. / Mode. » (depending on your BIOS);
Change mode « Ahci. » on the « IDE » or « RAID » ;

Figure 3. Put the IDE value for the Configure SATA AS string.

Save settings selecting item « EXIT Saving. Changes » In the tab « EXIT » . The computer will be rebooted with a modified configuration.

Now you can re-try the installation. Go to the next chapter if:

OS installation still does not see your HDD or SSD;
Mode « SATA. Mode. » has already been put on « IDE » .

Manual installation of hard disk or SSD drivers

Return to this chapter is recommended after full familiarization with the previous one. This will help to exclude excessive action.
In most cases, installation image already contains in itself for a variety of drive controllers ( driver SATA.). However, if the model of the board of your computer / laptop is quite fresh (or, on the contrary, old), the drivers can simply be missing.

Therefore, we need to independently "indicate" them at the stage of choice system Disc. Next instruction This will describe this process. Start.

Step 1 - Search for the required software .
Download drivers from your laptop or motherboard manufacturer. First of all, focus on files, including one or more examples of words: Inf, SATA., RAID, RST.

Step 2 - Unpacking and reset to the carrier with the operating system.
Unzip the downloaded file into a separate folder → copy it to any place on the installation flash drive.
notewhat we need drivers do not containexecutable ". EXE »Files. Suitable only unpacked(Such drivers usually include folders: aMD., x.64 as well as many . inf files).
Step 3 - Specify the desired software in the disk selection window.
Insert the USB flash drive to the computer → we reach the stage of selecting a disk for installation. Here you need to find a button (or "Overview" ) And click on it.

A conductor will open in which you want to specify the required driver. .
Figure 4. Choose the desired folder with driver.
HDD (SSD) will be discovered if selected suitable drivers. Now you can continue the process by choosing SSD Disc.

Drivers are set, the drive is displayed. However, the master does not see or does not allow you to choose the desired section

In this case, try remove markupHDD / SSD directly in the window disk selection. Attention! The following actions lead to formatting drive and, therefore, to complete data loss. Make sure all are yours important files Saved on a separate disk.For this you need:

Press the button "Disc Setup" at the disc select;
"Delete" All existing sections to start installing on unbelievable space
Check the integrity of the image OS on the installation disk;
Re-burn the image to another disk at a minimum speed;
Use flash drive(preferably USB version 2.0) instead of a CD;
Make sure the working capacity of the drive: check the connection, power supply contacts, the performance of the motor and drive.

The above actions will help solve your problem. Otherwise resetBios. And try another / assembly of the OS.

Also in extremely rare cases can help reinstall the driver for DVD drive. Detailed information You can find in the chapter "", and the drivers for the drive on the manufacturer's website.

Conclusion

If none of the listed methods helped, try to look for a problem in the computer component (independently or resorting to the help of a specialist).