Prospects for the development of radio stations with the VOX function. Watch with VOX (voice control). Different types of batteries supplied

\u003e If the function was turned on,

it will turn off, (lights up

goes out and again lights up the blue indicator, and after

fit red).

\u003e If the function has been turned off, it turns on (will light up

blue indicator, go out and lights red).

\u003e Press and hold the "Intercom" button for 3 seconds.

to complete the Setup setup mode. As a result

the red indicator turns off, and the blue indicator will start

blink. Now you can start using BT1.

Intercom communication can be activated manually and voice. On the

soundproofing helmet.

To get the optimal result, you must select one

of the four levels of the microphone sensitivity: high, medium,

low and very low. By default, the average

level depending on the type of helmet and motorcycle.

include Intercom communication, you can answer phone calls

only manually.

Setting the microphone sensitivity level

1 Go to Setup Setup Mode.

2 Briefly press the "AUX" button - lights blue

indicator.

3 Use the "VOLUME +" buttons (volume level increases)

and "Volume -" (reduction of volume) increase

or reduce the sensitivity level. Every time

pressing the "VOLUME" buttons will temporarily light up

red indicator (confirmation). When you go to

the highest or low value is the red indicator

does not light up.

4 Press the AUX button again. Start blinking blue

indicator that will determine the set level

disabled, twice - very low sensitivity,

3 times - low sensitivity, 4 times - average

sensitivity, 5 times - high sensitivity.

Default - average sensitivity.

5 The red indicator is on (the device is in mode

setup settings).

6 If necessary, you can change the configured

the level of sensitivity, following the described instructions,

starting from paragraph 2.

7 Press and hold the "Intercom" button for 3

seconds to complete the Setup setup mode.

Follow the items of the above-described level instructions

sensitivity and in the third stage Press the "VOLUME -" button

(Reduce the volume) until the red indicator

does not stop flashing. Then click the "AUX" button and blue

the indicator will light up, which means that the function

instructions starting from paragraph 5.

instructions, choosing one of the four levels of sensitivity.

by special use

In this section, you will find several tips on the use.

BT1, which will allow you to use the maximum

devices.

Using Midland Radio Station

together with the intercom feature devices BT1

If you wish to use a radio station in a group

people and at the same time maintain Intercom communication between the driver

and the passenger, you must:

\u003e Enable third-party communication feature (see

instruction).

\u003e Disable if it was turned on, VOX function - voice

activation of communication.

\u003e Connect a special cable radio station

to the wired audio input of the driver of the driver and press

"AUX" button (hear one confirmation signal)

\u003e Activate Intercom, clicking on the "Intercom" button.

activation

Turning off the VOX function is necessary in order to actively

radio transmission mode did not occur automatic

activation of the function of the Intercom. When the VOX function is turned off for

intercom Communication Activation You must click the "Intercom" button.
Attention! If you turn off the voice control function,

then on phone calls you can answer, only

pressing the "Phone" button.

Portable radio station Kenwood TK-2206 is made in compact design. The TK-2206 wagon body is made of high-strength carbon fiber, the basis of the transceiver design is a reliable chassis of aluminum. The SMA SMA Threaded Connector provides a reliable antenna mount to a transceiver. Kenwood 2206 radio station is quite easy to operate. The Kenwood TK2206 compact model without a display with a minimum of controls, thanks to this user does not require special skills to work Programming the TK2206 radio station frequency programming is extremely simplified and carried out through branded software, while the functionality of the radio is sufficient for the most demanding consumer.

In the portable radio station Kenwood TK-2206, proven quality, miniature size and excellent ergonomic design are well combined. The distinctive features of the professional transceiver TK-2206 are features as a priority scanning, voice signal encryption, built-in VOX (free hand function) and compliance with the requirements of the Milstd 810 C / D / E of the Milstd 810 C / D / E. protection and IP 54/55, which Allows you to use Kenwood 2206 radio stations under adverse conditions.

The Canewood TK-2206 bearing is small dimensions and high quality assembly. The advantage of Kenwood TK2206 is the simplicity of management. The built-in VOX function allows you to use a radio station in the "vent" mode when activating the Vox-A function, the radio station is activated when the user starts talking to the microphone, the mode has 10 levels of voice sensitivity control. The TK-2206 portable radio can operate in VOX mode not only in a quiet place, but also in a high sleeve place and will be included on the transmission exclusively to your voice, ignoring other sounds and noises. This function provides the VOX mode with increased noise. The mode of "free hands" is recommended in those places where the freedom of user's action is required or when he speaks of a radio without attracting the attention of others, for the mode of use of the Kenwood TK-2206 station without hands, a hidden wearing headset is used which is attached to clothes and does not stand out in everyday use .

In portable radio, TK-2206, for the simplest method of controlling multiple channels, a priority scan function is provided. Station hardware features offer 2 methods of priority and standard scanning. The transceiver allows you to immediately respond to the received signal without having to search or switch channels. In the shockproof model KENWOOD TK2206, a digital signal is used to automatically transmit subscriber identification. Coding mode Cenwood TK-2206 Coding provides access to the communication system and separating users to groups on the frequencies used on the Kenwood Case 2206 are located two side function buttons that are programmed to perform various functions that can be involved by the user during operation. In the Kenwood Transceiver TK2206, a powerful speaker has been built into a powerful speaker providing a radio station with a broken and high-quality sound. Sixteen channel radio kenwood 2206 in its purpose can be used as an alternative replacement of the stations removed from the production of Kenwood TK-2107 and Kenwood TK-2106.

Kenwood TK2206 radio station functions

16 memory channels
Output power 5 W
Built-in VOX mode
Built-in scrambler speech
Fleetsync digital warning protocol, including DTMF, QT and DQT alarm
Programming with a PC or Laptop
Voice Privariating Channel Room
CTCSS encoder / decoder allows you to form several independent conversational groups on one channel
A two-frequency symplex mode that allows you to use a radio station in communication networks having repeaters
Scanning
Scanning Function "Talk Back"
Two programmable keys
Duration limit timer
Locking keys
An incoming call alert
Programming parameters and configuration using a Windows PC
Selective call function
Remote Disable / Enable Lock
Companer of the audio signal
PTT ID function (Automatic caller identification)
Changeable microphone sensitivity
Advanced Kenwood audio system

Technical characteristics of the Kenwood TK-2206 transceiver

Model	Kenwood TK-2206
Frequency	136-174 MHz
Number of channels	16
Channel width (step)	30/25; 15/12.5 kHz
Battery voltage	7.5 V ± 20%
Operating temperature range	from -30 ° C to + 60 ° C
Antenna input resistance	50 Ohm.
Frequency stability	± 0.00025%
Distribution of Channels	38 MHz
Dimensions	54 x 122 x 21 10 mm
Weight	160 g
Receiver
Intermodulation	65 dB.
Audio output power	0.5 W, distortion< 10%
SuperGetherodine with double frequency conversion	there is
Transmitter
Output power (low / high)	5 W / 1 W
Modulation distortions	< 5%
Microphone input resistance	600 Oh.

Kenwood TK2206

Transceiver Kenwood 2206.
Nickel-Metallgid Battery
Single charger
Removable antenna (like "whip")
Instructions for the radio station
Packaging

Installation of the clip of the waist attachment.

Install the extension clips on the battery, as shown in the figure.

Installing a headset or tangents (supplied separately).

The headset or tangent is connected to the connectors on the right side of the radio station. ATTENTION: Connecting and disabling the headset or tangers is performed only when the radio station is turned off (you do not need to disconnect the battery).

Controls.

1. The switch on / off regulator and adjust the volume level.

2. Antenna.

3. LCD display.

4. Speaker.

5. Microphone.

6. Indicator.

7. Button up.

8. Down button.

9. Keyboard.

10. Place of fastening of a wretcher.

11. Battery retainer.

12. Clip of belt fastening.

13. Battery.

14. Tone call button.

15. Button RTT.

16. Button forced opening noise-lifter.

17. Connection socket or tangents.

1. When you press the FUNC and MENU button, the radio station will switch to a service image.

2. Signal and transmission receipt level indicator.

3. Depending on the operation mode, the values \u200b\u200bof the settings are displayed.

4. Maximum power transmitter indicator.

5. Indicator of activated repeater frequency.

6. CTCSS Code Activation Indicator.

7. DCS Code Activation Indicator

8. Activation indicator VOX function.

9. ACTIVATION ACTIVITY INDICATOR (automatic transmission time limit).

10. The indicator indicates that the channel is listed in memory.

11. Ton call indicator.

12. Keyboard lock indicator.

13. Accumulator charge level indicator.

14. The set button of the tone call.

Functions and operations.

Turning on the radio station.

Turn the regulator 1 Clockwise To turn on the radio station, turn the controller to turn off the radio station. 1 counterclockwise before clicking.

Volume.

Regulator 1 Set the required volume level.

Noise-cancel.

Noise allowance allows you to cut off an unbelievable radio interference signal. To set the noise reducer response level, click F. and then button 1 SQLWell, the display will display the established level of the noise pod.

Buttons 7 and 8 Set the required level to do this button. 8 Before the emergence of ether, then press the button 7 Until the noises stop, it will be an ideal signal-to-noise ratio.

The NexEdge ™ system provides the ability to use the automatic VOX function, available using special accessories (only in conventional mode).

1 Description

The automatic power transmission function (VOX) function is used to monitor voice activity on an additional microphone. When a voice is detected, it is transmitted by a radio station. In case the voice activity on the additional microphone is absent, the transmission mode in the radio station is turned off.

2 Use

When using the VOX function, a number of questions should be considered. First of all, the transmission activation function of VOX voice is designed to transmit radio stations when voice activity is detected. This means that the radio station will transmit every time the user says something. If the radio station user is located next to another subscriber, the radio station may detect the voice activity of this subscriber and start transmission. To successfully use the VOX function, the radio station user must be aware of the presence of any possible sources of sound capable of leading to unintentional inclusion of transmission by a radio station when there is no need. Secondly, the position of accessories to activate the VOX function is an important factor in its use. The radio station user needs to be placed in such a way that the minimum level of external noise is provided.

3 Temporary Disable VOX Function

In situations where the use of the voice activation function (VOX) can be undesirable, the radio station user can temporarily suspend it by clicking on the Intercom button (PTT). The radio station immediately suspends the VOX function and includes a transmitter. For subsequent gear, the radio station will operate in normal mode (i.e. without using the VOX function). Work using the VOX function will be restored if the user reincarnates the function through the menu or by pressing the corresponding programmable button.

To disable voice activation function (VOX), you can use the corresponding menu or a programmable button.

4 Tone Conversation Resolution

When using voice activation function (VOX), together with a tone conversation resolution, you need to know how the radio station will behave. When the tone is disabled, the radio station operator may begin to speak, which will turn on the radio station and the transfer of the entire phrase spoken by the radio station operator. However, if the conversation resolution tone is enabled, the radio station operator needs to use a keyword, the word "launch" in order to bring the radio transmission mode. After pronouncing the keyword, the radio station operator must wait for the call resolution signal, after which it can be started to talk, which will allow the entire phrase entirely, without loss.

Warning with Vox "Free Hands Mode" is equipped with a temporary or permanent inclusion function on speech transmission in automatic mode and are designed to monitor activation by the voice of the radio device on the built-in microphone. After the device detects a voice, it will begin to transmit it by walking. If the activation is absent, the VOX mode is turned off.

Features of the Watch with VOX (voice control)

When using the VOX system, some questions must be taken into account. The VOX system is used by a subscriber to transmit speech data by a radio when determining the voice of the user. This means that the radio will be activated every time the subscriber starts the conversation.

If the radio is located near another subscriber, the device can recognize its voice and activate the data transmission.

In order for the VOX function to use effectively, the user should be aware of the presence of any extraneous sound sources, which may cause an unexpected activation of the radio.

An important parameter for inclusion of the VOX system is the location of accessories. They must be located so as to minimize the level of foreign noise noise.

If the VOX function is not needed, the subscriber can temporarily disable it by pressing the RTT key. The radio stops the voice activation function and translates the device to normal mode. Thus, the user can enable and disable this feature as needed.

When using a width with VOX, together with the tone signal of the beginning of the conversation, you should know how the device will be done. If the tone mode is not active, the user of the radio can start a conversation, but not the entire phrase can be heard by another subscriber. If the tone is enabled, the user must use the code word to start the VOX function. After the code word is pronounced, the radio will turn on the voice function.

Buy radio swans in Moscow in our online store you can buy wages with VOX in Moscow of the world's leading manufacturers at the most reasonable prices. We offer radio stations with voice activation feature that will be able to provide high-quality communication even if the user cannot use the radio station as usual. We deliver goods to all regions of the country with the best motor vehicles of Russia. If necessary, the managers of our online store will select the most optimal model of radio with the VOX function, as well as the most convenient way to deliver and pay for goods.