Samsung Galaxy S3 is not charging the battery. Why Samsung Galaxy S3 phone is not charging. Wireless charging for Samsung Galaxy S3 - nothing complicated. Samsung phone is not charging

The reason for writing this article was the inadequate job of the phone SAMSUNG GALAXY S3.who served faith and truth and a half. However, before taking on to the writing of the article, it was analyzed and tried on own phone A sufficient number of tips and recommendations intended to eliminate glitches arising in this model.

1. Some causes of glitches in the phone.

1 . Telephone pulling frequent sounds and at the same time in the left upper corner The display appears the on-mode icon " Car"Although this mode is disabled.

2 . For connect to computer Phone is not determinedBut at the same time an alert appears on the display. Stand connected"And accompanied with sound pops up icon and notification of the on-mode" Car" If the phone does not disable from the computer, a notification appears after a few seconds that the application Touchwiz screen Completes its work. Then this application again begins its work and after a short period of time it completes it again and then restores it again. This process can last while the phone does not disable from the computer.

3 . If try disable phone with buttons at the moment when he pulling frequent sounds And the display can appear the on-mode icon. Car"After turning off the phone immediately turns on myself. And after shutdown, it will be turned on independently until it takes the battery for a while. At this point, the phone wants to split the wall.

4 . For connect to charger Alert appears on the display. Stand connected" The indicator shows charging, but the phone does not charge, or it is charged ... very slowly. Also in the process of charging, accompanied with sound can pop up the "car" mode icon.

5 . The phone at any time can spontaneously reboot.

To eliminate the above problems, some tips and recommendations were triggered, which were found on the Internet Network:

reset to factory settings, flashing the phone (do not recommend), reinstalling the USB driver, replacing the USB cord, buying the original uSB cord, extraction for one hour of the battery, removing the SIM card, reinstalling on the computer "PC Sync" program, install "Samsung Smart Switch" - all these dances with a tambourine did not help.

3. Causes of faults.

Experienced was established that everything is uSB phone connector And first of all it dirt inside the connector, Finding there along with the plug of the charger and gradually with this plug, the rambling, which is why the cord plug ceases to enter the connector to the end.

The second cause is oxidation of contacts inside the connectorwhich occurs under the action of the supply voltage, moisture and dirt, and contributes to the formation between the contacts of transitional resistances, due to which the glitches arise in the phone, because it determines it somehow in its own way.

Third reason is exterior of the external walls of the USB phone connectorWhy, because the plug begins to hang out in the connector and this is lost contact between the tracks of the plug and the connector. As a rule, such a malfunction occurs when we continue to use it in the process of charging the phone, gradually expanding the walls of the connector.

In all these cases USB. the connector is replaced, however, you can try to make preventive repair and restore normal phone operation.

4. Preventive USB Connector Repair.

If telephone es only sounds And notifies O. included mode « Car", Just clean the connector from dirt. To do this, we need alcohol and sticks - toothpicks, which are chosen in thickness so that the tip of the toothpick can move freely inside the connector between the outer wall and the central platform with the contacts.

The wand can be treated with a knife, but it becomes softer. In principle, the soft tip can be operated, but in this case the sticks will need more.

Turn off the phone and remove the battery.
The tip of the sticks gently clean the dirt from the connector. Then the tip is abundantly wrapped in alcohol and wash the remnants of dirt from the inside. If the tip becomes completely dirty, then change the wand. In my case, it took three sticks.

The tip of the sticks gently drive along and across the contacts and follow the state of the tip. When it becomes dirty or completely soft, we take another wand and clean the tracks with contacts until the tip remains clean.

Now dried the connector, insert the battery, turn on the phone and listen to its work for a couple of days. If the sounds are disappeared, then it's done. Congratulations.

If the phone has problems with connect to computer, First of all, clean the connector from dirt and try to connect. If nothing has changed and the phone continues to bullure and the computer still does not see it, you will have to level the outer wall of the USB connector to return its original condition.

Turn off the phone, remove the battery, the SIM card, the USB flash drive, if installed, unscrew 10 screws and remove the rear lid. The cover is enough to pull your fingers for the thin side of the case and pull up and it will easily succumb to.

We take a screwdriver with a flat tip, put on a USB connector, as shown in the figure, and on the handle we make one light impact of a small object, for example, pliers. Then we insert the battery, turn on the phone and connect to the computer. If the phone is buggy and is not defined as multimedia device, I'll turn it off again, remove the battery and make another punch connector. In my case, two shots had enough.

Boots must be applied carefully not to damage the board and do not break the conclusions of the connector with which it is soldered. Otherwise, the phone will have to carry in the workshop and overpass the connector.

Here in principle, and all the moments with whom I had to face when operating the phone Samsung Galaxy S3.. I agree that this is not all. But if your phone has one of the above-listed features, then before contacting a specialist, you can try to eliminate the malfunction yourself, and if you need, then hold prophylactic uSB repair Connector. Well, if you manage so that still you have to change the connector, then your soul will be calm, since everything was done on your part. And as a supplement to the article, look at the video.

Alternatively, read the article in which one of one is described. Maybe it will suit you more.
Good luck!

The so-called wireless chargers for mobile devices - have already been not a sensational deficit in the domestic retail. However, many manufacturers have not yet released their own wireless charging systems for their smartphones, and the popular Samsung Galaxy S3 is among such devices.

In fact, last year before the release of the new flagship in the smartphone line, Samsung representatives mentioned several times about the company's plans to release for. But the promises remained the promises and the official Samsung-Ovsky for S3 users have not yet seen.

And, it is very likely that they will not see. The network is overwhelmed with rumors and assumptions about the coming, and the long-awaited Samsung will most likely begin to release for a new flagship. Wait and see. However, if you already have S3, and the desire to acquire just such a charge, without waiting for the manufacturer to please you with something more or less acceptable, both in terms of functionality and the price, then there are also options.

Folk craftsmen, it turns out, has long come up with a fairly simple way. So, in order to add the option to your Galaxy S3, it will take some time, some money and accuracy. The proposed solution is based on a relatively cheap kit for wireless charging no longer a new communicator. Palm Pixi..

Further on points:

1. Collect the necessary details and tools:

- Palm Touchstone CHARGING DOCK (about $ 10 - here and then prices)
- Palm Pixi Touchstone Back Cover - Palm Pixi's Rear Smartphone Lid ($ 3)
- Network adapter for and USB cable ($ 5) - this is important, similar devices of other manufacturers are not suitable
- Copper tape on adhesive basis
- Scotch

2. We disassemble the rear cap Palm Pixi
It is necessary to neatly unscrew the black gasket on the back of the lid. You can just do it with your fingers. Next, remove the silver sticker. Both items - both gasket and sticker - you need to save, they will be needed later.

After that, before tearing out anything else, it is necessary to take a small piece of paper (the kitchen parchment is perfect), cover them the visible part of the scheme and carefully, but carefully note the contours of the coil and the surrounding four metal disks. The resulting deposit to the side - it will also come in handy.

Now with the help of a knife, carefully separate from the cover of the copper coil, (in fact, these parts are just elements of wireless charging) and four metal disks.

3. Install the wireless memory components on Galaxy S3
Remove the back cover of your S3 housing. We put the parts removed from Palm on the S3 cover: the coil and L-shaped fee are located in that place and so as shown in the picture.

Then, with a silver sticker we rush the coil from above. Now guided by our drawing, we place all four metal disks around the coil, after which they fix their position with scotch. Fix discs must be securely, since they are kept on the basis of the charger.

4. Connection
So that now upgraded back cover Galaxy S3 passed the charge, it is necessary to create a connection scheme properly. To do this, we prepare four pieces of copper tape size 5x25 mm each.

On the L-shaped part of the board we find two terminals. We take one of the prepared copper ribbons, bend it about 5 mm from one edge and cover the top terminal, the remaining part of the tape after that stretch to the edge of the cover at a low angle and tightly glue to the plastic (see picture). Similarly, we make the bridge from the second terminal to the edge of the lid, but under a slightly large angle. Be sure to make sure that the copper tape is well adjacent to both terminals. You can press the terminal more tightly with a conventional pencil.

To the left of the battery on the smartphone housing, we find a couple of terminals. The two remaining copper ribbons fold from the ends as well as the previous ones, and neatly, but we securely glue to the terminals and the case as indicated in the picture above.

5. System checking
We set the lid on the Galaxy S3 and put the device on the base connected to the power grid. The indicator on the smartphone screen should show that the device is in charging mode. Works? Congratulations!

Now you can turn off everything, take off the cover again and take all the farm installed there is removed with the Palm black lining (or black tape) so that everything is really beautiful.

If after all manipulations, the smartphone does not want to charge, then this may be several reasons:

the ends of the copper tapes are poorly glued to the terminals (check, by proving a pencil or glue in a new one);
a piece of ribbon on the lid touches the opposite tape on the terminal of the case (we check that the ribbons on the cover are narrow enough and not in contact immediately with both ribbons on the housing);
the components on the lid are set incorrectly (we are checked with the existing template, set the coil correctly, after which you check the voltage on the terminals using a multimeter - should be 5.5-5.6 volts).

It's all. By the way, in such a Touchstone base, your Samsung Galaxy S3 will be charged much faster than from USB.

Is your phone broken? ? The situation is not pleasant, but still this problem can be solved. In our service center PCMOL first will diagnose, in order to determine the cause of the breakdown, because the reasons may be somewhat.

Damaged power connector. If he is broken, then it will be necessary to completely replace it. It will take from 2 hours of time.
If the power chip is defective, you will need at least 4 hours to replace it.
The device got a liquid or the phone suffered as a result of mechanical impact, after which it stopped charging. Repair we perform after full diagnosiswhich leaves from 30 minutes.

Is free

Go to models

890 + 490 rubles.

850 + 490 rubles.

400 + 490 rubles.

1200 + 490 rubles.

1800 + 490 rubles.

In our workshop without problems will be eliminated any breakdown. Since all parts are original, our customers receive a long warranty.

Often, when the phone is not charging from, the first thing will be convicted that the cord is intact. Perhaps he just does not work. As a rule, it fails as a result of non-accurant operation. Users often twist the cord, as a result of which it is driving, ceases to function. This problem is very easy to decide, you just need to buy a new one.

If everything is in order with him, then you need to check the cell phone. Perhaps the connector broke. It often comes in disrepair with non-accurant operation.

If Samsung Galaxy C3 9300 has ceased to charge, first check under charger. It is possible that it does not work, with the result that the battery does not receive power. Check it is very simple. It is enough just to use another similar to the device. If this did not help and the problem remains, it means that you need to quickly go to the Psmol service center.

Our experienced masters necessarily move the device and determine the reason why samsung Galaxy S3 I9300 S III does not charge. Sometimes problems arise because of the software failure, the failure of any components of the phone, in particular, the nutrition chip. We can easily replace any damaged item. Just install a new one. All spare components are original, but even despite this, we sell them at the lowest prices.

Sometimes the phone does not charge from the fact that the battery simply exhausted the resource. In this case, we will simply replace it. New battery Provide the normal performance of Samsung.

Whatever the problem is, the phone should be attributed to the workshop as quickly as possible. If the phone is too for a long time To be in a non-working condition, the situation will only worsen. Our specialists will not refuse to help you. From any situation, we will find a way out. As soon as the breakdown, you will be given a long warranty. After that, we will be able to give the phone back. We are confident that in the future the situation will not happen again, and your mobile will work efficiently, and will not let you down!

Navigating on records

It happened a little less than two ...

Unfortunately, today, people who own Samsung phones suffer from the fact that the phone does not charge or charges, but with great interference. This problem is B. lately It became fairly common.

This article for those people who also encountered this problem. If this problem is detected, it is necessary to immediately take the necessary measures, because this problem It is impossible to let the samothek. Next, we consider in detail in detail why this happens to the phone (not charging) and what to do in such cases.

Cause

In the event that you are trying to charge the phone from computer device or with help standard method Through the socket and the Samsung phone does not work, the reason for this may be a malfunction of cables. First of all, you need to carefully view all the cords on the phone. If you checked, and they turned out to be integers and workers, then the reason is not in them. It is necessary to further look for the cause.

The reason may be:

It is quite likely that the connector itself is not fixed in the phone. If this is true, it will need to be replaced;
In fact, if the same connector is a bit cut out of the so-called pCB, the phone will not charge;
A powerovering controller can be flooded. In the event that it is true, then it is necessary to replace it;
If the phone, this indicates the damage to the power chain. This part is quite significant throughout the system, so it is necessary to carry out diagnostics before it is directly repaired;
A sufficient small percentage can be other problems.

It is also quite likely, the problem is that the phone is quickly discharged, but very slowly or does not charge at all. Then the problem is in the battery itself.

Such problems are quite common and people do not know what to do in these cases. Therefore, provide solutions to problems.

Eliminate breakdown

First of all, it should be noted that if the problem is not in the charger, it is best to contact a specific service center. There they will quickly spend the necessary diagnostics and determine the cause that you have not been able to determine.

In many centers, there are all the details in order to replace the breakage and provide repair of the high Quality. Often in all centers price for repairing the phone is permissible. Moreover, the advantage of service centers is the provision of warranty on the entire telephone.

A fairly common reason when the phone does not charge - this is a breakdown of certain electronic components in phone. In the case of such a breakdown in any service center, a person must explain than this malfunction is justified and what to do so that this is not repeated. It is also worth understanding that when they say that the phone does not charge, imply a quick discharge of the phone's battery.

A fairly frequent and common cause is the arrival of the battery to break down for long-term reasons. In such cases, you can simply replace the battery for a new one, and it will hold a long period.

Very often, the phone is turned off due to the discharge of the battery when the sound or vibration signal is applied. This is justified by the fact that the phone once fell, and such a breakdown happened.

Not so often, but the phone is discharged due to the internal problems, namely, some virus. Such a reason happens only on smartphones. To prevent such a problem, it is necessary to remember that the antivirus can be applied not only on computers, and also on mobile devices.

Failures inside the phone also happen, after which the phone itself cannot recognize the charger. In this case, recognize the problem and the more eliminate it, it is unrealistic. Consultation and help of specialists are simply needed here.

The minimum problem is that the screen fails. For example, after flashing the phone on the screen, the fact that charging may not be charged, and the battery itself is safely obtained by charge.

Not charging samsung phone

Faced with the problem of recharging your smartphone, a number of problems can be solved on your own. After conducting an inspection and a small diagnosis, you will easily eliminate or eliminate the most obvious and widespread reasons why your Samsung Samsung Galaxy, A3, S6, S4, S3 and other models have stopped charging.

The most frequent reasons when the Samsung smartphone does not charge

deep discharge;
cord and power supply;
connectors;
accumulator battery;
problems with software;
mechanical damage;
moisture hit.

We analyze each possible area in more detail, due to which the manifestation of such a defect is possible.

Deep battery discharge

If you do not follow the manufacturer recommended by the manufacturer, the mode of discharge and recharging, without receiving the power from the electrical network on time, the gadget could get a deep discharge of the battery. This happens when the voltage drops the desired nominal value, which is indicated directly on the battery itself in volts.

And now, when connected to a PC or charging, the devices cannot recognize your smartphone. At home will help leave the gadget for a long time (several hours) connected to the charger. Or use the Fixture "Frog".

In most cases, it helps to return the battery capacity, or will it help you the repair workshop. Samsung phone, where for this it will be used laboratory block Nutrition with the required power.

Charger

Diaward charging on another device, connect the cord to the PC. It is necessary to exclude the recharging problem in the cord and power supply.

Look carefully cord and power supply. Visually, they should not have any damage. The cord must be smooth, without bends, infertion, fractures. Isolation should be along the entire length.

If you find any damage - be sure to replace the new cord or block. The use of such components is fraught with a closure and failure of more serious and expensive phone components.

Problem Connector

The next step will be an inspection of the connector for connecting the charger. Apparent mechanical damage will immediately say about the need to replace.

Also, the problem may be in poor conductivity due to contamination (dust, corrosion from moisture). It is convenient to use a toothbrush. Carefully clean the connector and try to connect the charger again.

Accumulator battery

It is likely that the Samsung Galaxy, A3, S6, S4, S3 phone and other models are not charged for the failure of the battery itself. Battery bloating or its oxidation is directly talking about it. Then you need to replace it with a new one. This can be done independently, but you can contact the specialists of the service center.

Software failure

Some malicious applications are able to apply such damage to your gadget. Regular anti-virus cleaning of the program is needed to prevent any malfunctions in the work of the smartphone. If you can no longer include a gadget, as it is discharged, contact your specialists for restoration work. Receive the settings to the factory or offering flashing.

More serious reasons why smartphone Samsung. It ceased to charge the charging will determine in the service center and it is best to correct the defect. So you will receive a guarantee for work performed and free service in case of repetition of the problem.

Purchase dear smartphone Nowadays (in connection with the ease of the dollar) - the case is even more expensive and responsible than a year ago. Therefore, it is doubly insulting if a freshly reduced phone somehow flounders.

I will tell my story associated with Samsung Galaxy S3. At about six months after the purchase, I began to notice that the phone was very quickly discharged - literally for 2 hours there was a 100% charging.

And I don't even play on the phone! Sometimes he could not touch him, and he still discharged in the middle! And now one day I only charged the phone, put it with you, and here in a couple of minutes he stamped - 15% of charging! How so? I connect it to the charger, and the charging does not go! The horrors immediately scroll into the head: in repair, week or more without a phone.

Okay, it came to the head to remove the case and look at the battery. And ball swelled! Just to huge sizes! How did she not explode in my hands yet? Very lucky! As a result, the battery, naturally, did not put back, I bought a new one in the morning, now the phone is charged normally. By the way, the battery could bloom from the fact that I left the phone on charging all night. I don't do it anymore.

But the swelling battery is only one of the reasons that Samsung Galaxy S3 does not charge. What other people can be?

2. Faulty charger. Our house has three identical samsung and three charges, respectively. So we noticed that not all chargers charge the same - some faster, some slower. It is important that charging was original - neoriginal charging Poorly charge Samsung. And in general, we have one that not only does not charge, but also discharges Samsung!

3. There may be problems with the cord. Check simply - try charging another phone using charging (the same applies to the removable charging unit). If the charger is faulty, you will need to buy a new one.

4. Problems with the inlet for the charger in the phone itself. Check too easy: Take another charging. If several different chargers do not charge the Samsung Galaxy S3 phone, then it's time to repair.

As you can see, not everything is so scary in cases when Samsung Galaxy S3 does not charge - most often you can buy additional accessories like a battery or charger, for which, by the way, the guarantee when buying lasts quite a little bit - about a month it seems to be.

Video Overview

All (1)

Nowadays, many have already become accustomed to life with a smartphone for so much that it seems terrible for a couple of days! Both the phone and the Internet, and all the rest of the utility of the smartphone made our lives more comfortably and, a little, more fun. In one day, my friend Samsung Galaxy S3 began to charge badly. Remembering the story of his appearance, I already understood that it was only in the charger. Initially, the charger that was included - charged him slowly, and I tried to charge him with an old charger from the LG phone: the connectors came up, charged quickly, everything was fine. As long as the charge input into the phone is not gradually loosened, and in order to appear the phone charge indicator, some efforts have been applied. Deciding that it was easier to buy a new charger - I did, having bought a charger in the nearest kiosk for 170 rubles. It connected normally, but he was charged slowly and in the end he was completely discharged (during charging I used to smartphone). I went to the nearest service, left a phone for diagnostics and possible repair. As a result, this campaign cost me 1000 rubles. - they said that the nest of the entrance was soldered. I do not know what they soldered, but the result is the same - the old charger that was charged - not visible, the new charger is charged slowly. In the service, I was offered to leave a couple of days for a couple of days for further diagnostics. I decided to solve this question yourself. To start bought new battery (Original Samsung - for 700 rubles). Searching information on the Internet - found a very useful article that helped me (I hope now for sure)! At least now it is clear that the reason for slow charging was in the strength of the current. Installed a program that shows how much MA is served. The original battery, as well as the new Chinese showed the number from 100 to 300 mA. There must be a value approximate to 1000 mA. That's what he charges slowly. As a result, I made two almost non-working chargers - one: the USB-phone lace - took from the original charger and connected it to the power supply unit (the one that is turned on in the outlet). As a result, it will be charged now with indicators of 500-700-900 MA. Hooray!

The text, found by me on the forum http://mdforum.ru/showthread.php?t\u003d11132 - below:

Everything that is written below is intended primarily for Samsung Galaxy S III users (International version of the GT-i9300) with an original battery at 2100mA · h

First of all, you need to make sure that it comes to the battery in the phone

We put a small but useful program with the GalaxyChargingCurrent widget, in which we will watch only the readings of Current Max. For the purity of the experiment, the battery charge should be less than 90%, and even better less than 70%. Why? - The answer at the very end under the "Note" spoiler. Turn on the body for charging from the original (Samsung) network adapter In the outlet and look at the menu-\u003e Settings-\u003e The battery is charging from the network (AC), and not from (USB). Then look at the galaxychargingcurrent reading of the Current Max. Ideally, for charging from the network, 1000 should be (just 1a, as written on the adapter). But if it is 800-900, then it is also normal. If when charging from the network shows 460, then the body has decided that the charge comes from USB.

Smart charging in the off state will determine which way to dig (the normal charging time of the original battery is from 2 to 2.5 hours, small errors are possible).
If the smart is turned off, the order of 2.5 hours is charging, and the inclised longer means you have problems from "Software".
If the disabled smart is charging longer than 3 hours - it means problems from the "iron".
Old / faulty / served his / dying battery can be charged faster than two hours (there are charge cases up to 100% per one! Hour).

Problems from "Software" and ways to correct

The wine can be an increased cost consumption. In other words, the battery is discharged faster than it is charging. This can occur for several reasons.

The first reason "It's you, and the second is all yours ... Sorry \u003d) No matter how funny it sounds, but sometimes the user himself is to blame. You should not use smart to full until it is charging. Playing "heavy" games or run energy-intensive applications during charging is not recommended. The more active you will use Smart, the longer it will charge. Any connection (data transmission via USB, 3G or WiFi) affects the duration of the charge, the active connection is more so, since it causes the battery warming. With an increase in the temperature for every 10 degrees, the reaction rate increases 2-4 times (Vant-Hoff ©), in this case, the process of self-discharge and current leakage in the battery increases 2-4 times, it flashes faster, not to mention the discharge. For active connected Charging time may increase several times and with the signal full charge It will not quite correspond to the truth (temperature and time charge limit on the side of the chip). Based on this, the charge with an actual telephone completely turned off 4-8 times shortens the processes destructive for the battery during charging and reduces the charge time itself. Conclusion: I put the body for charging - forget about it to complete charging. Relax yourself and let him relax \u003d)
The second reason - "spontaneous" smart consumption. You seem to do nothing, and the charge literally melts in front of your eyes, the body starts to lag, to respond to your actions with a big delay, the drawing of the interface slows down. There is also strong heating at the bottom (in the SIM card / flash drive area) - smart is heated stronger than usual (I personally noticed the heating to 49 ° C). This is a sign of working, possibly in the background, an energy-intensive application. Or an error occurred in the application, it hung and the Android tries to fix everything on their own, consuming the charge in addition to the usual. Try to stop all running in this moment Programs (for Samsung Galaxy S III - Long Pressing on button Home. Calls the task manager with which you can complete everything). If it does not help, then remove the body with charging, disconnect the battery for a couple of minutes, insert back and connect to charging again. In the future, you need to calculate the culprit and disable or configure again.
Third reason - Frozen battery. Do not charge the battery, after exposure to it negative temperatures, wait for it when it is heated to the surrounding (room) temperature and its energy properties will return to the initial values. When cooled, the processes inside the battery slow down. Therefore, with the active use of the phone, a premature message about full dischargeAlthough there is still a stock. The effect is similar to high inner resistance, but is reversible. Due to the slower chemical reaction, the battery simply does not have time to supply the required amount of energy, resulting in a stress drawdown. It is because of the slower processes, the charging of the chilled battery will be ineffective. Moreover, it makes it impossible. It should be waited when the battery temperature will reach room floor.

Problems from "iron" and ways to correct

Bad contact. You need to clean the USB socket in the body itself, the wire plug, the adapter socket. If you do not know how you do not know how, do not want, you are afraid - take the body to the service center or in any confidence in the confidence in the repair of phones and for the symbolic fee you will be sold not only to the USB nest, but also microphones, dynamics, etc., all Blind and smuckle (kidding). It did not help - we read on.
Faulty standard uSB cable. There are two options: crimp the microusb plug or disassemble the MicroUSB plug and disappear it or crimp the wires along the new one. If you do not know how, do not know how, do not want, you are afraid - you will help you the new USB cable. How to choose a high-quality wire - only by scientific tyk. We try different wires and compare the results in the GalaxyChargingCurrent and charging time. Perhaps you will help original cable Nokia CA-101. Also remember that not all wires are the same useful - do not strive to use the wires longer than one meter. It did not help - we read on.
Faulty adapter. At the moment, one option - get a new one. Or at your own fear and the risk you disassemble your adapter, repair it and share the result. Do not forget that the new adapter must respond to two conditions: the MicroUSB connector and the output voltage / OUTPUT 5V and 1000MA (\u003d 1A). 5v necessarily, more - it is impossible, less - it is possible, but the demon is a sense. 1000mA (\u003d 1A) - the maximum that the body will take it if the charging is 2000mA (\u003d 2a) - it is not scary (the body takes only 1000mA (\u003d 1a)). The best option is a monolithic charge (without the possibility of disconnecting the adapter and wire). Not only the GNUSMAS adapter, but also Nokia, HTC and others can come. It did not help - we read on.
Faulty battery. Signs of the old / faulty / serving their / dying battery are a quick discharge and bloating. Pull out the akum from the body and look at it into the profile, for example, on the line with the connectors. If the upper and lower planes are noticeably convex - change it to a new one. The malfunction of the defective battery is the spontaneous shutdowns of the smart on the charge residue more than 5%. Before shutting down, you can notice the screen flicker. Also, a serviceable battery, charged to 100% (when the green diode lights up), can not lose more than 1% during the solar loading process. The procedure for checking the battery for a malfunction - charge until a complete charge (when the green diode lights up), disconnect from charging, turn off the smart and turn on in a couple of minutes. If the battery has lost more than 1%, the battery is faulty. 1% may be "lost" during the shutdown (termination of application operation) and in the power process ( a large number of Applications in autoload), in the usual situation this procedure It requires much less energy and, accordingly, after switching on the smart with a serviceable battery, the readings will remain 100%. It did not help - we read on.
Faulty phone. There are two options for answering: Krusky and Delchev. And if seriously, we repair in the service center or in any confidence-building, the office on the repair of phones. Or buy a new phone.

and yet (some helped):

Remove the /data/system/BatteryStats.bin file After deleting the named file and reboot, the charging problem is immediately solved. If the problem is repeated in the future, it is necessary to remove this file again.
Battery calibration. To solve all problems with charging, you must calibrate the battery.

NOTE: Charge time all Li-Ion batteries With the initial charging current in 1C (numerically equal to the nominal value of the battery capacity), an average of 3 hours. The full charge is achieved at a battery voltage equal to the upper threshold, and with a decrease in the charge current to a level, approximately equal to 3% of the initial value. The battery during the charge remains cold. As can be seen from the graph, the charge process consists of two stages. On the first (hour with a small) voltage grows with an almost constant initial charge current in 1C until the first achievement of the upper stress threshold. By this time the battery is charged by about 70% of its container. At the beginning of the second stage, the voltage remains almost constant, and the current decreases until it reaches the above 3%. After that, the charge is completely stopped.http://www.ixbt.com/mobile/review/lipol.shtml

Infinity, especially for a daisy club.