How to clean the CD-ROM and DVD drive: preparation and cleaning rules. How to remove data from a DVD to prepare it for a new record? How to clean the dvd player at home

How to Clean DVD Laptop

Although the DVD is already cutting into your age, however, they still have on many computers and laptops. Many have a Windows licensed system that is stored on the disk, and it takes it to install it. DVD drive (Although it can be recorded on the USB flash drive and install it from it). Therefore, I want to consider in this article, as you can, with simple tools, clean the DVD drive in your computer or laptop.

The method that is described below, I have been using for many years and has shown myself very effective.

The reason that the DVD drive began to work badly, do not read discs or do it with interruptions, most often - the dust hitting the laser lens. Here we will clean her.

Required tools:

Philips screwdriver (cross);
Ordinary clip (it needs to be dispersed);
Cotton swab or wand.

How to clean the DVD computer drive

To begin with, remove the DVD drive from the computer. It is not necessary to do this in the laptop.

I turn up upside down and unscrew 4 screws that mount the lid.

Very carefully remove the lid and postpone. Our attention will be a fee with electronic components.

Now put the drive so that it watches frontal panel on us. Our broken clip insert into a small hole intended for emergency opening of the drive tray. Boldly give a clip until the tray does not come out of his place.

I pull out a manually tray about half of its length. Now remove the facial plastic panel. To do this, you can press the side latch with a screwdriver.

Face panel side latches

Now we turn the drive to the lid down and carefully remove it from there.

Take the DVD drive from the lid

Now you can see the same laser lens that need to be cleaned. Carefully consider it. Most likely you will find small hair or dust on it.

Do not try to remove contamination with your hands. May remain fatty divorces that will be difficult to eliminate.

We take a cotton wand and lightly smile with a lens pollution. It is not necessary to polish the lens, it is enough just to remove dust and hair.

Clean the lens with a cotton wand

After this procedure cleaning the drive, you need to collect it in the reverse order.

How to Clean DVD Laptop

The procedure is similar as with a computer drive. Just do not need to disassemble anything.

Just put forward the DVD tray and gently wipe the lens with a cotton wand.

Most likely, after such manipulations, the DVD will start reading the discs ignored by them before. If the improvements are noticeably not, most likely to help him no longer help and only replacement is required.

If you like this guide, put like and share it with friends.

PcGu.ru.

How to fix the built-in drive of optical disks in a laptop with your own hands

DVD or CD drive breakdown in laptops is the most common flaw in the devices that have worked for more than 2-3 years. Dust, which unambiguously falls on the focusing lens after many years of operation, for sure, if it does not lead to a complete failure of the drive, it will make it work less reliable and fast. The reason for the complete failure to perceive or record information from the computer to the optical medium can be covered both in the hardware and in the system malfunction. Remember: Drive optical disks In laptops can refuse to read information from DVD discs For very many reasons.

First, it is necessary to 100% eliminate the likelihood of software failure in the operating system. You can simply insert a disk drive that can be used as bootable. Either the installation distribution with Windows is suitable or some service disk designed to work with a hard disk, as well as for treating viruses, banners, system preparation operating system from scratch, etc. The main thing is to put in the BIOS that the DVD drive is the first in the download, i.e. it is from him, and not with hard diskYou need to load. Probably, many who independently installed the operating system either from the disk or from the Flash drive, they know what we are talking about. If the download of such a disk occurs quite successfully, the fault is to search in the installed operating system, namely: in drivers, as well as in software productswhich can one otherwise change the system configuration of virtual and physical optical drives. Remove the entire doubtful software for recording, copying DVDs, and also check in the device manager, whether your drive determined correctly or not. Of course, all the software faults under the same article describe almost impossible, but you can give a universal advice: make the system restore.

Secondly, if the drive refused to perceive boot disk, Most likely, there is a hardware problem. Often, all the solution of the problem is reduced to the fact that it is necessary to clean the focusing lens. Dust, falling on this lens, prevents the laser head beam normally transmit a signal reflected from the DVD. If at any stage of operation, it led to errors of reading or writing, then in one "beautiful" day the drive can simply refuse to read perfectly clean and new Disc. The most correct way to solve such a problem is to clean the focusing lens.

The whole truth about cleaning disks

Now the so-called cleaning discs received a huge distribution. The idea of \u200b\u200bsuch disks is definitely good, but the technical performance is not always acceptable. Some samples may generally, instead of use, simply "finish" sensitive mechanisms and optics of a laser head. Also, the improper use of cleaning discs can lead to the fact that the user itself simply finally "will achieve" a drive. The instructions for such disks is often written either in English, or in Chinese, which makes an understanding of the principle of action, appointment and use such a disk is simply inaccessible for a Russian-speaking person. The main error of the users is improperly applying cleaning fluid. As weed, it is necessary to apply it only on certain cleaning huts, besides very little, there is a disk about an angle of 45 degrees relative to the horizon line. The excessive amount of this fluid simply fills the laser head, making reading information in fact that the event is not possible.

If we talk about Chinese cleaners from a category of 100-150 rubles, then their purchase will be not justified with both practical and economic side. And if your problem is not in the lens, then it is money thrown on the wind. As the protection of the reputation of cleaning discs, we note that new contactless discs began to appear. Their main difference lies in the fact that they work like wind turbines, that is, they blow the laser head without direct contact. It is such cleaning discs that we recommend to acquire without fears to harm the sensitive elements of the optical drive.

How to clean the DVD drive without a cleaning disc

Many master-repairmen, although they themselves are sometimes recommended to use cleaning discs, but they never use them. Cleaning disk is a solution for novice users and housewives. It is much more professional and better clean the drive only when you take it out of a laptop and discern. To disassemble a drive of some complex equipment and conditions do not need. Only a table, a set of screwdrivers, clip, needle, syringe, ear sticks, as well as isopropyl alcohol.

How to remove the drive

First, you need to de-energize the laptop. Turn it face down, extract rechargeable battery.

How it would not seem ridiculous and not reliable, but the fact remains a fact: at all modern laptops All mounting the drive to the laptop is made using the 1st screw. We take a thin cross screwdriver and remove it.

Also this method You can use yourself when you need to urgently pull the disk, and the electricity is disconnected, and the battery is discharged. After inviring into the technological hole, the needle or paper clips will open open, and you can pull it completely by pulling the disc-received tray.

How to disassemble the drive

Turning uncovered optical drive The front side is down, you can notice the rear panel cover, which hides many important elements of the laser system.

Extract 4 retaining screws, and the lid obediently shakes without the slightest effort on your part. After removing the rear panel cover laser driveWe have access to the revolving part of the laser diode, as well as the optical system.

Then you can wear the lid, as well as tighten the 4 fastening screws.

How to wipe the focusing lens

The lens is very sensitive to touch, so it is better once again to touch it either with your hands or tools. To begin with, you can try to restrict ourselves to purging from a sphailed air can.

If it does not help, we recommend using a ear chopper, pre-dipped in 90% isopropyl alcohol, wipe the lens. The second dry and clean end of the sticks need to remove the alcohol residue. Remember that cologne, moonshine, vodka is simply unacceptable for these purposes. You just harm. Isopropyl alcohol evaporates rapidly, relatively non-toxic, and also does not leave marks on glass and lenses, which is very important in the framework of the technical task. Then you need to dry out again everything from a sphailed air can. It remains only to gather everything, insert a drive and screw the fastening screw. The assembly is simple and intuitive.

Finally, we note that in some cases, the breakdown will not succeed, because it can be wounded in a distinguished LED laser, in the worn mechanics, in the blurred driver chips, etc. Therefore, the last repairs is the full replacement of the DVD drive.

muzhik-v-dome.ru.

Repair dvd drive do it yourself

How to repair a CD-DVD directly?

This is a small story with pictures on how to revive CD-DVD, and probably Blu-ray drive, without resorting to expert help. There are several common causes that can lead to full or partial inoperability of the drive. The elimination of these reasons is not to be repaired, but rather maintenance CD-DVD-ROM-A and may well be performed by a user who has some skills to work with electronic technology. Read more on OldOstober.com.

The most frequent causes of the causing drive failure.

Wear drive belt (passic).
Increase friction in the loading mechanism.
Laser lens pollution.
Reducing the PDA laser.

To eliminate any of these reasons required partial disassembly Drive. The design of the drives may vary, so the accompanying pictures should not be perceived absolutely.

Tools and materials.

For preventive work We will need the following tools, materials and components. OldOstober.com.

Staple Stationery.
Conducting cruciform.
Medium-sized brush.
Calica (cotton fabric).
Silicone lubrication SI-130.
Passion.
Cleaning napkin.
Thin screwdriver.
Tweezers.

Begin. Disconnect cables from the drive and unscrew the fasteners. Remove the drive from the housing system Block.

Disassembly.

Disassembling any CD-DVD drive begins with tray extension. To push the tray, you must first make a simple device from the stationery clips.

Caution, looking at the end of the stationery clips to the technological hole on the front panel of the drive, groped the part of the mechanism that is responsible for blocking the tray. This item is strictly opposite the opening. Press it and the tray is slightly advanced. Now it can be pulled out with your fingers.

Press the latches securing the front panel of the drive. First, press one of the side latches.

Then, press the latch located at the bottom of the drive, and another side zag.

We put forward the front panel, unscrew the four screws with cruciform caps and remove the panel of metal casing.

We press the latch and separate the tray from the main mechanism.

Carefully clean the mechanism from dust and dirt with a brush. If the old lubricant is strongly contaminated, then we remove it with the help of a bosale and apply a new lubricant.

We replace the woven passion new. After that, we wipe the passion and the inner surfaces of the pulleys with a cleaning napkin or a blank moistened in alcohol.

Wipe the laser lens with a cleaning cloth. Dust, having mastered on the upper surface of the lenses, can not be seen with the naked eye, but it is almost always present there.

If the drive is very old or it is known that too many disks were recorded on it, and there is a problem of reading or writing, you can try to increase the laser current. This rather thin operation requires patience and can take quite a long time. Do not cheer this procedure if your drive simply does not read several old disks or discs recorded on other people's drives. This can be caused by a lot of different reasons and the magnitude of the laser current here on the 38th place.

Adjust the laser current is best when the drive is in a semi-discharge state.

To start the drive without casing and the front panel, you will have to remove the front wall of the disk tray.

Somewhere on a carriage with a mounted laser, there is a small-sized potentiometer, the position of the engine of which is determined by the laser current. The location of this potentiometer depends on the design of the drive.

Before you twist this screw, we definitely sketch the position of the slot to have a point of reference, and in general, in order to be able to return it to the original position.

Rotating the screw by 10-15 degrees first in one, and then to the other side, each time you check the reading quality in some program, for example, Nero DiscSpeed.

Just checking it is desirable immediately on several types of carriers, for example, CD-R and CD-RW or DVD + R, DVD + RW, DVD-R, DVD-RW, etc. Probably not necessarily check all types of supported media, but check at least those that you all use.

Multipurpose universal drives, these are pretty compromise and therefore often, some types of discs they read better, and some worse. For example, by increasing the laser current, you can get the perfect reading of CD-R and take half of your CD-RW unreadable.

The assembly does not represent any difficulties, except for one point. When inserting a tray into the loading mechanism, you need to combine the lock of the loading mechanism with the guide grooves located at the bottom of the tray.

The slider is usually spring-loaded, so it is necessary before flying the tray into guides, fix the slider in the correct position using a tweezers or another suitable tool. On the photo the position of the slider is fixed with sewing.

If you have at your disposal, it turned out to be a small set of liesics of different diameters, then you just need to pick up suitable instance. If there is no such set, you will have to buy a passion.

And although the era of video and audio tape recorders passed, on all sorts of radio rolls, you can still condemn rubber passions in the assortment.

When buying a passion, you need to pay attention to several of its parameters immediately, such as: section, diameter, elasticity and quality of the volcanization of rubber from which it is made.

The cross section of the passics can be defined on the eye, as the likelihood that you will be able to find a passion of a strictly appropriate section is small.

The luster diameter can be determined by attaching the old passion to the new and make sure that the diameter of the new one, slightly less than the old one.

Elasticity can be measured using an improvised stand, like the fact that in the figure.

I usually check the properties of the passion to the point without any dynamometers.

The quality of rubber vulcanization can be determined by color and tactile sensations. The color of "wrong" rubber is deep black, and the surface is smooth with a high reflective ability. While the "correct" rubber has a slightly grayish tint and a more matte surface.

Also, the quality of the volcanization of rubber can be determined by the time of recovery source size. For the test you need to strongly stretch the passion with your fingers and very quickly reset it with a plafhmy on a flat surface. The faster the passion will adopt the initial size, the higher its quality. If you can notice on the eye, how the diameter of the passion is changed, that is, he seems to be eaten, then such a passion will last long and better not to use it at all. However, it is not a fact that you will find a passion in the bazaar high QualityYes, and exactly the same as required. Therefore, for the absence of the best, you can buy something that is, but with a correction for diameter, section and elasticity.

And so, all these four parameters affect the properties of the passion. Choosing a passion, you need to take all them. If the liesic cross section is slightly smaller, then you need to choose a passion slightly shorter and vice versa. If the quality of vulcanization is low, then you need to choose either a little more cross-section, or a little smaller diameter.

If the passion is pulled too much, it can lead to a jam or premature wear of the disk loading mechanism. If the passion will be pulled too much, then this can cause its slipping relative to the engine pulley.

If there are several loved ones in the bazaar, it is better to immediately buy several different to pick up the most suitable at home. The price of a passic for a CD-DVD drive may vary from $ 0.3 to $ 0.7.

Close themes.

Reducing the noise of the system block of the computer.

How to disassemble and lubricate the fan if he taughty.

Install Skype on PC-586.

oldOstober.com.

Cleaning DVD drive

As I already wrote earlier in other articles, the biggest problem for the computer is dust. It is clogged where only you can in such quantities that sometimes you just have a diva. DVD-drive of optical disks is no exception.

Dust, if the device does not clean, affects the operation of the drive tray, reduces the accuracy of the laser mechanism and affects the quality of the clamping mechanics. In general, the DVD drive must be cleaned at least once a year. Optimally - once every six months.

For cleaning and maintenance of the DVD drive, you will need lubricant, cotton wands and alcohol. After removing the DVD drive from the system unit, you must remove its front panel. First of all, it is necessary to push the drive tray. It is done with any long and thin subject (needles, clips, a piece of wire long 3 cm.).

On the front panel of any DVD drive, there is a small hole (p.2 on the bottom photo). Behind him (from the inside of the panel) there is a manual tray opening mechanism. It is necessary to press up with a slight force to this mechanism through the hole and the tray will be pulled out by 1-2 centimeters, after which it can be pulled out to the end manually.

Next from the tray you need to remove the dust cover. To do this, turn the drive and, moving the cover with your fingers, pull it down. On the lid, as a rule, there are two latches (p.1 on the bottom photo) and two guides on which the cover is kept. She is removed without much effort.

Next you need to drown the latches of the front panel. They are usually four (two below, two on the sides), or five (two on the sides, three below). After removing the front panel, the bolts (4 or 5 pieces) are unscrewed on the bottom lid of the DVD drive and the cover is removed.

DVD or CD drive breakdown in laptops is the most common flaw in the devices that have worked for more than 2-3 years. Dust, which unambiguously falls on the focusing lens after many years of operation, for sure, if it does not lead to a complete failure of the drive, it will make it work less reliable and fast. The reason for the complete failure to perceive or record information from the computer to the optical medium can be covered both in the hardware and in the system malfunction. Remember: Optical disk drive in laptops may refuse to read information from DVD discs for very many reasons.

First, it is necessary to 100% eliminate the likelihood of software failure in the operating system. You can simply insert a disk drive that can be used as bootable. It will be suitable for either the installation distribution with Windows, or some service disk designed to work with a hard disk, as well as for treating viruses, banners, system preparation to install the operating system from scratch, etc. The main thing is to put in the BIOS that the DVD drive is the first in the download, i.e. It is from it, and not from a hard disk, you need to load. Probably, many who independently installed the operating system either from the disk or from the Flash drive, they know what we are talking about. If the download of such a disk occurs quite successfully, the fault is to search in the installed operating system, namely: in drivers, as well as in software products that can change the system configuration of virtual and physical optical drives in one way or another. Remove the entire doubtful software for recording, copying DVDs, and also check in the device manager, whether your drive determined correctly or not. Of course, all the software faults under the same article describe almost impossible, but you can give a universal advice: make the system restore.

Secondly, if the drive refused to perceive the boot disk, then, most likely, there is a hardware problem. Often, all the solution of the problem is reduced to the fact that it is necessary to clean the focusing lens. Dust, falling on this lens, prevents the laser head beam normally transmit a signal reflected from the DVD. If at any stage of operation, it led to errors of reading or writing, then into one "beautiful" day the drive can simply refuse to read a completely clean and new disk. The most correct way to solve such a problem is to clean the focusing lens.

How to clean the DVD drive without a cleaning disc

How to remove the drive

First, you need to de-energize the laptop. Turn it face down, remove the battery.

No matter how hard it seems ridiculously, but the fact remains: on all modern laptops, all mounting the drive to the laptop is made using the 1st screw. We take a thin cross screwdriver and remove it.

Also, this method can be used to armared when you need to urgently pull the disk, and the electricity is turned off, and the battery is discharged. After inviring into the technological hole, the needle or paper clips will open open, and you can pull it completely by pulling the disc-received tray.

How to disassemble the drive

Rotating the opened optical drive face down, you can notice the cover of the rear panel, which hides many important elements of the laser system.

Extract 4 retaining screws, and the lid obediently shakes without the slightest effort on your part. After removing the cover of the rear panel of the laser drive, it opens access to the back of the laser diode, as well as the optical system.

Then you can wear the lid, as well as tighten the 4 fastening screws.

How to wipe the focusing lens

The lens is very sensitive to touch, so it is better once again to touch it either with your hands or tools. To begin with, you can try to restrict ourselves to purging from a sphailed air can.

Many users prefer to buy rewritable discs to be able to record information on it several times. But before cleaning the DVD RW disc from the information, it is worth choosing the most suitable way. You can make it possible using some disk recording programs or you can use the tools installed on the computer operating system.

If not installed programs To record disks, you need to go to the "My Computer" section, and in the window that opens, find the CD / DVD drive icon.

We carry the mouse cursor on the drive icon in which the disc is in need of cleaning.

Press it right key mouse.

In the drop-down menu, we find a string where it is written "erase this DVD-RW", after which we press the left mouse button on it.

The CD Wizard window will open, in which you need to click "Next".

All files located on this disk are deleted. This process can take from a few seconds to several minutes, depending on the number of recorded files and the speed of the rewritable disk.

After the disk cleansing is completed, the "CD recording wizard" window will be information that the operation is successful and the media is now suitable for recording new files. Here you press the "Finish" button.

If, after executing the above operations, it has not been cleaned, it may mean a malfunction CD / DVD drive, or the disk can be more unsuitable for subsequent recording.

Clear DVD-RW drive is possible very quickly and simply using Ultraiso or NeroburningRom programs.

To use Ultraiso to clean the disc, you need to open window Programs Select the "Tools" menu, and select the "Write the CD" line in the drop-down menu of the left key.

The "Record Image" window opens, in which we click "erase".

If the NeroburningRom program is installed on the computer, select the "recorder" in the open DVD-RW disk, and press the "erase rewritable disk" in the drop-down menu.

In the window that will appear after that (erase a rewritable disk), select the drive, the method of cleaning the disc and the rate of erasure.

After pressing the "Erase" button, the process of cleaning the rewritable disc will begin.

When cleaning the DVD-RW discs, it is necessary to fulfill the complete erase of all files. This will help exclude the reading of old data in parallel with the reading of new recorded information.

In the case when the disk was cleared not immediately or not from the first attempt, it should not use it, as this may lead to loss of information that will be recorded later.

To be able to overwrite data on a DVD disk, you must have a DVD-ROM-installed on the computer (DVD + RW format). In modern laptops and computers, the latest configuration, as a rule, such DVD-Roma are already included in the equipment.

DVDs are two species - with the ability to overwrite (RW) and without it (R). In the first case, you can use the drive several times, deleting and recording new data on it, in the second version, the information on the disk can only be written to the unique times. In our case, you need a DVD RW. Before you write down the new information on the disk with the data already available on it, you need to remove old data (format disk). This can be done using a special softwareor own means installed on the computer operating system.

How to delete information from disk - DVD + RW or CD + RW

If Windows is installed on a computer or more early versions Operational windows systemsthen best to format DVDs to use special programs. For example, which is one of the most popular PC users. It allows not only to remove the disk from the old information, but also to record new data on it. The program is particularly popular because stable work It also has a very convenient and visual interface.

Download installation file. nero programs You can be free on the Internet to then install it on your PC, step by step performing instructions of the installer. After that it is best to restart the computer, then insert into DVD drive disc And using a label on the desktop, start Nero Start Smart.

In the main menu of the program window, find the "Advanced" function, click on it with the mouse button. In response to this, the dialog box will open in which you must click on "Erase DVD", thereby activating the "program wizard". The wizard will display the tip screen using which you can read the disk from unnecessary information. After the disk is successfully formatted, a notification will appear on the monitor screen.

Use the built-in disk cleaning programs.

Windows Vista and Windows 7 operating systems have visual and consistently working built-in features for DVD formatting. After the system itself determines the disk installed in the drive, a dialog box appears on the monitor screen in which you want to click on the "Record to disk" function. In the new window that opens, select the disk name, then click on "Show formatting options" to set the parameters of the future record to the disk. If new information consists of one type files (for example, movies or music), then you need to select the MASTERED parameter so that the disk is in the future read by the equipment that reproduces these files. To collect on one file disk different types It is better to choose LFS. By setting the desired parameter, click on the "Next" button. In response to this, the formatting process is automatically started, after which the corresponding message appears on the monitor screen.

Useful video

Especially for you prepared video about how you can clear the data from the CD / DVD disk: