Connecting to the Internet Modem Setup. Proper configuration of the "Rostelecom" modem: ADSL, DSL, D-LNIK, TP-LINK. Connecting a modem to the telephone line

Connecting to the Internet is carried out on various technologies and protocols. One of the first was the telephone line, remaining relevant until now. The technology that uses this type of communication is called ADSL2 +. At the moment it is replaced by more convenient and high-speed options, but in remote settlements is still one of the main ways for wired connection to the "World Wire Weight". Consider in detail the 2640U DSL router, providing a wireless connection to the Internet.

The 2640U router is used only to connect using ADSL technology.

For acquisition, four variations of this model are available. Externally, they are indistinguishable, the difference is only in the versions of hardware revisions. The DSL connection method is already outdated, but still relevant for remote settlements.

It also has a wireless network connection feature. That is, it is used as a Wi-Fi device. DSL-router D-Link 2640U characteristics are identical to other models from the XDSL segment.

The 2640U router interface does not contain USB connectors, which means there is no possibility to connect a 3G / 4G modem to it or perform the firmware through the "flash drive". It also does not support the creation of a VPN server, using as torrent or DLNA servers. There is no possibility to make an individual configuration or change the purpose of the buttons on the equipment.

Appearance

DSL Wi Fi-modem D-Link 2640U is a black box with rounded edges. On the front side there are light indicators with a signature signaling the operation of the current connection. The power connector and ports are on the back side along with the only antenna.

The design is the same as most routers from the manufacturer.

Included to DSL equipment go all the necessary cables to install the network device. The main documentation and configuration assistant are on the disk included in the package.

Connection and preparation for work

Before you configure the D-Link 2640U router, you must connect it to the electrical network. To do this, use the power adapter, which is included. Phone cable connector Insert into a special device - splitter. It will allow you to divide the signal that goes on the Wires, two: the first is responsible for the phone, and the second is for providing Internet access. The last step is to connect the 2640U network cable to the network port on the computer.

Settings

The configuration of the network device is performed in two ways. Using the installation wizard from the disk either through the browser in the router menu. Consider each of the options in more detail.

To configure a DSL wireless 2640U router in automatic mode, you must first start the "Installation Wizard", which is on the disc with a set of delivery. Next, you need to choose the country and the organization providing access services to the Global Network.

In the next step, you will need to specify the login and password provided by the provider at the conclusion of the contract.

After that, the router automatically performs the necessary actions.

Connecting to the Internet manually on the example of some providers

If the first option did not help, or the user prefers to configure independently, you must log in to 2640U through the browser.

Now consider how to configure the DSL D-Link 2640U router depending on the selected provider.

"Home ru"

Officially, "Dom.ru" does not support DSL routers, as they use outdated Internet connection technology. But the following instruction applies.

Connection type (Connection Type) Type on PPPoE. Interface (Interface), or Connection Port, DSL (NEW). Name (Name) - Enter any value. This is just the name of the DSL connection being created.

Section "ATM":

The value of the VPI and VCI fields responsible for the DSL connection must be found at the provider. They are individual depending on the region of residence and port on the equipment provider's equipment. The remaining fields are left unchanged.

Section "PPP":

In the field "username" (username) and "password" (Password), enter the data provided by the provider for the DSL connection service. The remaining parameters - no change.

To use the IPTV function, you must set a checkbox in the "Enable IGMP" checkbox (Enable IGMP Multicast).

Press the "Apply" button. In the top menu, select System (System), "Save and Restart" (Save and Reboot):

On this, the primary configuration of the Internet on D-Link 2640U is complete.

Rostelecom

The service provider officially supports this model. Adjusting the Rostelecom Provider DSL D-Link 2640U router is identical to the above method. This is explained by the fact that both providers use the same internet setup procedure.

"Beeline"

For DSL router Wi Fi D-Link 2640U Internet connection via the Beeline provider is not possible, since it is not directly able to support connection via VPN servers of the provider.

To use it, you must purchase a second network device capable of maintaining this function. It is also recommended to immediately select a model through which it is possible to configure optics for the DSL wireless home router D LINK 2640U.

NetBynet

ADSL WiFi-router D-Link 2640U is not supported by NetBynet as a router to provide access to World Wire Weight. Before configuring according to the instructions of the DSL D-Link 2640U router, it is recommended to first contact the provider for advice. This is due to the fact that NetByNet necessarily uses the identification by the MAC address of the network equipment.

Wireless network

SSID: Come up with Wi-Fi network name. Country: Specify the state of finding a user. Channel: leave AUTO mode.

Enabling the "Hide Access Point" function means that the connection is invisible when trying to find it in a general search. To connect to the Wi-Fi network, you will need to manually enter the name of the access point, specify the password to it.

The remaining parameters are left without adjustment. Press the "Apply" button to save the changes.

Network authentication is an encryption algorithm used to protect the wireless connection. It is recommended to set the WPA-PSK / WPA2-PSK value. These are the latest standards that are not hazardous. In the "Encryption key" field, come up with a password for access to Wi-Fi. The rules for its creation are indicated above, when the process of changing the password to the 2640U network device was described. "WPA Encryption": Install TKIP + AES to reliably protect the access point. The remaining fields are left unchanged.

• Press the "Apply" button to save the configuration. Next, you will need to restart the DSL router to apply all changes made.

The above method will be able to pass the "Wi-Fi" to the 2640U router without special difficulties for the user.

Setup in repeater mode (repeater), amplifier, adapter or access point

The 2640U router is configured in different modes: Bridge mode, access point, repeater, or Wi-Fi signal amplifier. This will be discussed in separate instructions for setting up these options.

IPTV.

To configure IPTV on the DSL router, you must set the "Enable IGMP" configuration to the Internet connection. This was mentioned in the section of the article informing about the configuration of the DSL connection through the House.ru provider.

Then you should connect the TV-prefix with a power cable to the DSL router, perform the following steps in the Configuration menu:

Name: Come up with any name to connect. In the LANS section, mark the connector to which the TV prefix is \u200b\u200bconnected. In the WANS section - Bridge mode created earlier. Click "Apply."

Requires DSL equipment to save the configuration.

Dynamic DNS.

The 2640U network device supports the ability to set up a dynamic DNS server.

By default, DSL Wi-Fi Router Model 2640U proposes to use the DDNS address from the manufacturer. The user himself determines the most convenient service for it.

Security Settings (Antivirus, Firewall)

Then click "Apply", and then restart the DSL router so that the changes are preserved.

To enable the "Parental Control" function, you need to go to the "Control" menu, select the appropriate option. Next, click the Add button:

You must specify the following parameters. "Title": Come up with the name of the service. "Performance Days": Slide checkboxes in checkboxes for days for which this rule will act. The following two sections are responsible for the time interval with an accuracy of the minute, fill them. "MAC address": specify the physical address of the equipment for which this rule will be applied. Click "Apply." To use the parameters, the equipment is best restarted.

Setting up printer

The DSL modem cannot directly connect the printer. It is possible to use this equipment only to connect to the printer via the local network.

Possible malfunctions and ways to eliminate them

If the DSL router has problems, the first thing is to try to restart the device. Another option is to reset the settings to the factory. How to do it, is described below.

It is also worth remembering that cables can also be damaged. It is worth carefully checking all the switching on the equipment and devices connected to it. Sometimes there are situations where the problem is on the side of the Internet service provider. Then it is worth calling technical support, to get advice from experts.

If the DSL router still does not work, it is recommended to contact the service center. Masters diagnose the problem, help it solve.

Update firmware

Equipment over time is obsolete. In order to stop it longer, it is "flashing periodically". The manufacturer lays out fresh updates on the official website. For the 2640U model they download them to:

Last update dates back 2013. This means that this device is no longer supported by the manufacturer. Consider how you can update the DSL modem.

Via web interface

Through the "System" menu, item "Update by":

The window has two updates.

In the current example, the DSL "Wi-Fi" emulator of the 2640U network device is used, so the inscription is displayed on the screen: "Unable to check the availability of software updates."

Through a mobile application

There is also an update option through a mobile application. It exists for Android and iOS platforms.

Unfortunately, currently the 2640U model is not in the list of compatible devices. Accordingly, the user does not have the ability to produce this operation through a mobile application. The list is constantly updated, you can watch it in the app store.

RESET OF ROUTER SETTINGS TO FACTORY

Performing the settings on the device "DSL" 2640U is carried out in two ways. In the first case, it is enough to press the RESET button on the back side, while holding it for 10-15 seconds. The simultaneous reboot of all light diodes will show that the process is made.

The second option - through the web interface. To do this, select the "System" item in the upper left corner, hereinafter - "factory settings":

Within two minutes, the network DSL device will roll back to the factory configuration.

Output

DSL "Wi-Fi" Router D-Link 2640U is a model that supports outdated ADSL technology. It is suitable for work, mainly in remote settlements of the country, where in addition to the telephone line there are no other alternatives to the wired Internet.

To configure in the private house "D-Link" "DSL" 2640U is perfect. A pleasant and understandable interface, minimum of operations. Configuration is performed in 4 minutes.

pros

Network device 2640U refers to the line of budget DSL routers, that is, its price is acceptable.

It is possible to use in other modes other than a router. Excellent alternative as an access point

Minuses

Equipment uses XDSL connection technology rarely applied to date. For its performance on modern protocols, firmware is often required on third-party modes. However, this leads to the non-working state of the equipment.

WiFi Routers Link received quick and well-deserved popularity among users of the global network and in this regard, the question often comes: "How to set up a DOTER D LINK?" Below, the instructions that did not affect none of numerous Internet providers providing communication services at present will help most of the owners of the Link brand routers. Configuring the D LINK router will not cause problems even at novice users if there is an accessible instruction, describing in detail all the actions of the owner of the device in steps.

Preparation of equipment to the configuration procedure

Remove the device from the package and all of its associated component elements. Attach an antenna to the router housing (some models are screwed). Connect the Internet provider cord into the router connector with the inscription "Internet", and connect the PC network card with the link device by setting the plug into the LAN inscription.

Power supply cable Insert the device in the power supply socket and connect to the power grid.

After that, you must perform the preliminary settings in the PC. To do this, you need to execute the following sequence of steps:

1. Through the "Start" open "Control Panel";
2. Go to "Network and Internet";
3. Next, enter the "center of UPR. Sweets and Society. Available";
4. Click on "Izm. adapter ";
5. Select "Connecting on Lok.set" and call the context menu;
6. Click on the "Properties" line;
7. Click "Protocol 4 (TCP / IPv4)" and set the marks to "Get IP automatically" and "Get the DNS address automatically":
8. Click OK.

In the case of the existence of an already used WiFi, the router is recommended previously, before it started with it, make a reset of its settings to the factory state. In the rear panel of the device there is a special button with the "Reset" inscription.

It must be armed with a subtle and acute subject, for example, a straightened wire of the stationery clips, prescribe a key bluntable key and hold it for a few seconds. Wait for the full load of the device, usually this process does not take more pairs of minutes.

How to enter the router settings?

The algorithm of action consists of several stages:

Setting procedure

It is required to follow the following step by step instructions:

Configuring an ADSL Modem for home access to the Internet is a simple procedure, which may even have a person far from information technology. Some people mistakenly believe that for competent access to the Internet, you need to have a diploma or computer science. In essence, modern modems and routers have such a clear and friendly user interface that its setup does not require any serious knowledge of programming languages, as well as the depth knowledge of system administration. As part of this publication, basic software and hardware settings will be considered, which, you connect everything with your own hands.

Secondly, network wires will be required, as well as a special splitter separating the line on 2 branches: 1 - on the phone, 2 - on the modem. Using a splitter (divider) must, as it makes it possible to simultaneously work in a stationary phone and modem. 2 cables will also need: the first is a standard telephone cable with RJ-11 connector at the ends, second cable - twisted couple with rj-45 tips. All wires must be supplied with the modem.

Thirdly, it is necessary to competently organize the modem connection to both the telephone line and the computer. First, connect the cable of the telephone line to the splitter into the socket where Line is written. From the two remaining slots of the splitter marked with the pictograms of the phone and the Internet icon, create a chain on the modem and on the phone. By the way, contrary to general opinion, connecting a stationary phone to the line is not necessary for the normal operation of the Internet. Even if your home has no telephone, but there is a telephone line - you will be 100% you can configure the Internet. The main thing is to connect the wires correctly. Connecting the line to the modem is performed through a single port under the RJ-11 plug. Ethernet ports for a twisted pair cable with RJ-45 tips are used to communicate a modem with a network card of your personal computer. The light indicator LED on the network controller of your computer speaks about a successful hardware connection of the modem to the computer. If the LED on the network card did not catch fire, then this means that either in the cable there is a break, or the RJ-45 connectors are compressed not by that standard. For our purposes, a cable is not necessary with a crossover (crossover) crimping, which is used to connect a computer-computer, and with a direct crimping required for connecting a computer-router. As a rule, complete with the modem already has a necessary cable.

How to set up a modem connection

In essence, all the settings of the modem connection are reduced to the installation of the network card driver, as well as configuring the modem via the web interface. First-in-speed, check the correctness of the network equipment definition in the device manager. If you notice any alarm icons or other messages about a software error, or incompatibility, then delete the current version of the driver and install the new version previously downloaded from the developer site of this equipment. Next, you need to check whether the DHCP protocol support is enabled on your wired adapter. Clearly to lift IP addresses, of course, better, but easier and clear to use DHCP, where data manipulation occurs in automatic mode.

How to get into the web interface of the modem configuration

It is possible to reach the web interface of any modem or router by typing 192.168.1.1 in the address bar there is absolutely any Internet browser. For example, Google Chrome will suit. After entering the cherished address, the login window will appear in the modem configuration interface. The input to the protected zone of the modem occurs using the login and password. Standard values \u200b\u200bof this pair "Admin" and "Admin". If someone has changed the data from the login and password parameters without your knowledge, then reset the password will not be much difficulty: it is enough to poke a needle or a clip into the "Reset" button. In all existing modem and router models there is a given technical reset button, which allows you to easily and simply bring the modem settings to factory values. After resetting the parameters, you will easily get into the configuration panel.

Subtleties settings

First of all, make an update on the modem, unless, of course, you have other Internet access to download the new firmware. Before starting the configuration, find a contract for the provision of Internet access services from your provider. The main thing is to find a card where the pair is login and password. You also need to find out what value of the "VPI" and "VCI" pair must be stapped for your region. Depending on the plug-in service, provider and from the region of your stay, these parameters can differ significantly. For example, for the Stavropol Territory, Rostelecom Internet supports the parameters "8" and "35" - for the service "Home Internet", and "0" and "35" - for television for the "Interactive TV" service. Naturally, for other regions, these parameters are seriously different. Therefore, it is necessary to find the parameter table for your provider.

Typical setup on the example of the D-LinkDSL-500T modem

First, it is best to use the setup wizard. First you need to press the RUN WIZARD key. By this, we will launch a model for creating a model modem setup.

Secondly, choose the time zone. Click Next

Thirdly, choose the type of connection that we now want to set up. In our case, this is "PPPOE / PPPOA".

Fourth, we prescribe the username, password, "VPI" and "VCI". You must also put the type of connection "PPPOE LLC".

And fifth, press the Next button and reboot the modem by clicking on the "Restart". It remains only to wait for rebooting and entry into force. On this Internet configuration, you can read successfully overwhelmed.

Rostelecom DSL-2500U router is inexpensive and easy to use the LINK device to ensure that the "World Wire Weight" is connected to the "World Wire Weight". It is sold in the CIS countries, used to access the "global network" by phone.

Network equipment is not able to distribute wireless communication, as well as connect via Ethernet to external resources.

Consider in more detail how it happens on the D-Link DSL-2500U model setting for Rostelecom.

Configuring network equipment D-Link 2500U "Rostelecom" occurs in several simple steps. Credentials for the first login, IP address, serial number and other characteristics are given as information on the device label. The modem is equipped with the following connectors:

1. The adsl connector joins the cable from the phone.
2. The network cord supplied with 2500U connects to the LAN port on the modem and the network adapter socket of the workstation.
3. The adapter is connected to the AV connector, and then the device - to the power supply.

The main parameter is located in the main WAN menu. For its initial configuration, you must pass the authorization process. We carry out the following actions:

Configuring the connection 2500U Rostelecom to the Internet

Setting up the Rostelecom D-Link 2500U router is intuitive and simple.

There is a Russified version of the built-in software, that is, residents of the Russian Federation will not appear linguistic problems. Two configuration options are available: automatic and manual. Let us dwell on each of them.

Using "Wizard Settings"

To automatically install the model 2500U, open the "Master", follow the prompts on the screen. First, indicate the area of \u200b\u200bplacement of the network device. Next, you will need to specify the login and password specified in the contract with Rostelecom.
The built-in software will complete the initial D-Link 2500U configuration: the option of access to the PPP Over Ethernet network is enabled.

Self-configuration

If the user wants to conduct an independent setting, it will need to perform the following steps:

It is important to note that the modem in question is not intended to distribute Wi-Fi. It is used to receive data from the line and send them to one device via LAN.

Advanced Routher Settings: Manual Mode

It is possible to independently select the mode of operation of the D-Link modem. In the "Control Panel" of the device, select the "Network" subsection, then the WAN tab and click "Add". After that, the "Creating WAN connection" dialog area appears on the screen. In the "Connection Type" paragraph, select one of the possible ways:

• Bridge: Using the Add button, specify VCI and VPI, mark the NAT and Network Screen items. The mode is intended for remote regions of the country, where Rostelecom could not have been able to ensure that stable access to the "World Wire Weight".
• PPPOE or PPPOA: The above parameters, username / password are prescribed. The remaining items are noted as needed. This option is used in most cases.
• Static IP: Address, Network Mask and IP Gateway are indicated by the subscriber manually, based on information from the Rostelecom agreement.
• Dynamic IP: Data is not prescribed. The client's IP address is assigned automatically from the Provider's DHCP server.

After completing the input of the change parameters, save.

Setup IPTV.

IPTV mode is used to deliver a digital television signal through an external network. For its stable functioning, we connect the TV console from Rostelecom to the model 2500U. Unfortunately, the parallel activity of the workstation and television is not possible, since the LAN connector is only one. We perform configuration of the router as follows:

Setting up a DNS server

This subsection of the main menu permits manually specify the addresses of the DNS servers of the communication service provider. The factory settings are set to "Automatic receiving address from the provider".

Remove the mark with the Enable Automatic Assigned DNS option. Next, enter the addresses of the DNS servers obtained from Rostelecom. After making changes, we save them, and I reboot the modem.

Additional features of the ADSL modem "Rostelecom"

The D-Link 2500U router supports the Parental Control option. This is the ability to block or allow access to selected sites at the set time. Regulation of the rules occurs through the "Control" subsection. To create a new action, click "Add".

Important! The rule being created is installed only on one plug-in equipment (smartphone, laptop, tablet computer). This is due to the fact that the identification of devices is carried out in the physical address.

We compile a schedule in the relevant sections. The latter are filled at the request of parents. Adults independently set the time limit of the use of the Internet.

The following subsection is responsible for switching on / off the URL filter. Selects the type of filter: block or enable. Then you should click "Change". The new window indicates the URL, and through the colon - the port.

Changes are saved, and the network device is rebooted. After turning on the Rostelecom modem, unnecessary sites will block unnecessary sites or allow the transition to them at the specified time.

Output

D-Link DSL-2500U is a budget networking device for connecting to the "world web", based on XDSL technology. The device is a bit outdated, as new models are characterized by stronger technical characteristics. However, if it is impossible to use high-speed tariff plans for its functionality, it is enough. D-Link DSL and other models from a similar line are distinguished by high demand in remote regions of the country, where in addition to telephone lines for connecting to the Internet, nothing else is offered.