Protective glass on the phone

One of the most common problems is to enter water or moisture under the iPhone display. Let's look at what is in this case to make the owners of the iPhone.

If the iPhone fell into the water, then immediately pull it out of it and turn off. You can't get the battery, as you need special sprocket screwdrivers.

If the device has to be transported, then no need to wrap it into the clothOtherwise, the humidity will be significantly higher, which is much more terrible for the apparatus.

Just put an iPhone on a horizontal surface and call home specialist. It is not worth upset, since in 90% of cases nothing but the display does not suffer.

Using a fane

The most common advice is to use a hairdryer or put a phone on the heating battery. The fact is that the high temperature, of course, will help evaporate the liquid, but can add new problems. Hair dryer is prohibited categorically. The air jet may opposite "driving" water deeper into hard-to-reach places.

Use Fig

There is another advice on the drying of the phone with rice. Rice really absorbs part of the moisture, but small. Therefore, if the iPhone had a very small contact with water and it did not get inside, then rice will help, otherwise, part of the water will still remain inside the iPhone.

If the water got under the display, then you can get rid of it using special equipment. The problem is that the display in iPhone is a module of the matrix, touchscreen, protective glass and backlight.

We disassemble the display iPhone layer

All these parts are glued together. And the water just falls between the backlight and the matrix. Therefore, it is not expelled from there. It will only help.

Between these layers, water falls and therefore appear display defects.

Although there are many waterproof devices on the market now, most smartphones are still poorly experiencing contact with liquids. To get under the rain is not the worst thing, which can happen, but to dry and return the working condition to the device, even after random washing or falling into a puddle or pool.

What to do if a prime touch phone

Before proceeding with any actions, you need to immediately disable the gadget. For phones with a non-removable battery, it can be done long by pressing the lock button. Otherwise, just remove the battery - so you will avoid short circuit, otherwise it will not be able to restore the performance of the device even in the service center. Follow such instructions like driving a gadget:

Disassemble the device. Ideally, each detail should be dried separately: remove the SIM and MicroSD cards. Remove covers, protective glasses and rear cover. To spin everything to the screws is not worth it, it will be difficult to collect the device back, so if you have a monoblock model (with an unclear case), stop at removing all inserted cards. Use screwdrivers only if you are sure that you know the gadget device well.
Put the apparatus screen up. Let the gravity make your business and enable water to accumulate at the bottom of the gadget.
Adsorb moisture with paper towel or napkins where possible. Turn the device slightly so that the accumulated liquid flows through the holes. At the same time, avoid sharp movements and do not shake the gadget in the hope of drying it faster, otherwise the water will again go inside and fill hard-to-reach places.

Keep in mind that turn on the device immediately after you rub the surface is strictly prohibited. The most important and last stage is the drying of the phone after the water. Depending on which method is selected, it will take different amounts of time.

You can dry the phone, leaving the device on the air for 3-7 days, but this is long and does not guarantee further operation, since the radio elements are oxidized under the fluid. Use an absorbent agent that will help stretch water from the device and dry faster.

How to dry the phone at home

The absorbent is a substance that pulls out and absorbs moisture. Whatever method you choose, you will need a container where the product and the phone will also be placed. Drying rules for each method below:

Put the phone in fig. This is the most famous absorbent. The fact that the phone can be dried in rice is not a myth, this means is effective. Put the gadget without a battery and a lid in a package with a cereal for 2-3 days. Once at 12 o'clock turn the device.
Use a silicogel feline filler. This tool is considered even better absorbent than Fig. To dry the gadget, place it in a container with a filler for 48 hours. In this case, the tool must completely cover the device. From time to time, turn the smartphone.
Dry the phone in silicone balls for shoes. Alternative option, according to the effectiveness of the previous one. Pulls moisture for 2 days.

The advice is currently relevant for all methods: to check the smartphone every 6 hours and wipe moisture with paper napkins from its surface. In addition, with severe damage, you can change the absorbent to the new one.

Is it possible to dry the phone with a hairdryer or vacuum cleaner

To dry the elements by removing the liquid from the internal apparatus, it is better to use a vacuum cleaner. To do this, put the narrow nozzle and consistently bring it to all the openings of the gadget. Remember that after this procedure, you still need to place the device in the absorbent or leave to dry in the air.

All the advice mentioned above are relevant for both smartphones that have been in water and for those that bathed in gas production, lemonade, tea and other liquids. Do not rush to wash the substances under the crane, but do all the items from the instructions or take the damaged device in service center - There they know how to dry it well.

The repair may be needed even when the procedure was produced correctly: diagnostics will show, did not oxidized under the influence of fluid board and radio elements. In addition, there are cases when water separations remain under the display.

Video

The modern market offers each buyer great amount different models Gadgets, smartphones and other similar devices. Despite the fact that the display is reliably, the buyer decides to extend its service life, acquiring protective glass. This is due to the fact that in time we are not so careful about smartphones, as in the first stage. Today we will talk about how to clean the phone in front of the glass sticker, how to get rid of dirt, remove the divorces, how to clean the gasoline and rainbow spot, trim, wipe the protective glass from the inside and what we need for this tool.

What is protective glass?

Protective glass is a modern view of the displays on smartphones and gadgets. It is manufactured using a chemical method based on tempered glass.

Important! Compared to an ordinary film, it is thicker and harder. That is why if this coating is present on the phone, it protects the screen from traces of fingers, scratches, moisture and even shock. Despite these characteristics, brightness and color does not change.

Due to the multi-layered coating, glass thickness varies from 0.25 mm to 0.5 mm, the composition of which is:

The first layer is always made on the basis of silicone. It is glued to the display.
The next layer is fastening. It is he who does not allow to spread with fragments if a crack or a mechanical blow occurred.
The third coating layer is an anti-reflective film. It retains the appearance of drawings on the screen if direct sunny rays or other bright light fall on it.
The protective layer protects against shocks, drops and other mechanical damage.
The most recent layer is a oleophobic coating. It provides protection against moisture, fingerprint and simplifies the screen cleaning.

For active use The upper coating that ensures the reliability of the unit is contaminated. It is then that the question arises about how to clean the protective glass of the phone. How to do it and what will be required for this, we will look at further.

Immediately pay attention to the state of the back side of your gadget. You may use information on how to remove scratches from the phone body.

What is a protective film?

The protective film appeared on smartphones for a long time. It is not a high-tech product and is present on each gadget. This product is characterized by the presence of three layers:

the bottom of them sticks to the screen;
the average absorbs ultraviolet radiation and provides brightness when bright light;
the top is responsible for protecting the display screen.

Important! The most important for the film is the correct gluing. To do this, you need to have a small skill, since the first time it can not always work out.

All protective films that are present on the smartphone and gadgets market are divided into three types: matte, glossy and mirrored. Let us consider every kind to understand whether there will be a cleaning difference:

Matte film absorbs glare, and also hides traces of fingerprints. The main disadvantage is that it worsens the image quality. However, its cost is very low. Many masters include such a film to technological and advise not to stop the final choice on this product.
Glossy protective film is the most popular among similar products. The main disadvantage of such a coating is that it is easy to damage. The film strongly reflects the light, the scratches and other mechanical damage appear quickly. Also visible fingerprints.
Mirror film is the least popular among similar products. The peculiarity is that with the extinct screen, it can mirror the image. However, the quality and brightness of the screen changes when sticking this coating is the main disadvantage.

All of the above films are polluted and especially this is noticeable when dust falls under the coating. How to clean the film for the phone, we will now discern.

How to clean the protective glass on the phone?

If you think about how to clean the film for the phone, then the ordinary scotch will help you, or as it is also called, the adhesive tape. For this you need:

take a wide scotch;
cut off a piece of approximately 30-40 cm;
printed it to the surface so that the sticky side is above.

After that, it is a protective film with a sticky side to glue to the scotch. Then very carefully and slowly immediately sprinkle the film. All dust that was present on the product would leave, and the sticky layer will remain.

Important! If you need to remove scratches from the top of the protection, then polish defects with felt, a soft cloth or with the help of auxiliary means - a tooth white paste, goye paste or olive oil.

Another way to clean the protective glass on the inside is the use of water and soap. For this:

You need to remove a contaminated product from the phone.
In hot water, wash off all the dust.

After this procedure, it is very good to clean the sticky layer soap. To do this, it is better to use two or three layers.
After that, take and rinse the soap solution under water. Look to the water glass with the film.
Then we glue the film to the purified wet display using an ordinary credit card.
We look so that air bubbles and other villins do not fall.

If nothing helped, the best way Restore the attractiveness of your gadget is to replace the protective part. On our site you will find detailed instructions About,

New models of smartphones for the modern user are not just a means of communication. Mobile devices that combine the functions of the phone and computer - the status thing, emphasizing the image and the impeccable reputation of its owner. But sometimes the overall style of the device is spoiled due to the appearance of cracks and scratches on the screen. Fortunately, the emergence such a problem You can prevent the protective film by planing on the display. But remember that with the inactive execution of this procedure under the film, ugly air bubbles remain under the film. Sometimes the defect appears as a result of sedimentation on the inner side of the filter of small dust. In this situation, it will not be possible to eliminate it, just overlapping the protective accessory again. The film will have to be completely replaced.

1 bubbles on the protective film of the phone: how to remove them?

Information on how to remove air bubbles from the surface protective filmwill be relevant and useful for mobile gadget owners that independently glue a useful accessory on display

2 Replacing film on the phone - the main nuances

The replacement of the protective film on the smartphone display needs to be made as neat as possible and in a clean room where there is no dust. The best option for replacing the film is a bathroom. The level of humidity in it is high, so the dust does not twist in the air, but settles down. Accordingly, it will not be able to enter the inner surface of the film that you are creating on the display. The technique of sticking the protective accessory on the screen of the smartphone consists of the following steps.

3 Air got under protective glass - how to remove it?

Remove air bubbles from under a more dense protective glass in the smartphone is a bit more complicated than from under the thin film. But if desired, everything is possible. To help you - the advice of experienced owners mobile deviceswho managed to independently solve the problem of air bubbles under protective glass.

1. If the air was accumulated under the surface of the glass in the smartphone, try to "squeeze" it from there, spending on the screen with a plastic card or a dense driver's license.
2. Remove air bubbles under protective glass you will help you an ordinary needle. Carefully grind it under those sections of the coating, where the air accumulation is observed. Lift the glass to release the air, and then press it again to the surface of the display so that the air masses do not hit it.
3. Fishing lovers can try to remove air from under protect glass using a fishing line. Carefully thread it under the protective accessory on the smartphone screen and swipe until the air bubbles disappear. Then get the line, and return the glass to the place, gently pressed it.
4. Fix the defect in the form of air bubbles on the screen of the smartphone will help household hair dryer. Experienced masters claim that air bubbles will disappear if the protective glass coating first warm up the hot air flow from the hair dryer (removing the device by 20-30 cm from the screen), and then putting the device for the night under the press from books (on a flat surface, down the display) . Usually for 12-14 hours all the air leaves, and bubbles disappear.

Note! Clean the inner surface of the protective film or glass from the smartphone can be using a scotch strip. Get it on the surface of the accessory, and then delete. The adhesive element will remove the dirt, fine garbage and dust from the film surface. After this cleaning, you can stick a protective coating back.
Useful recommendations for gluing film on the phone screen at home
If you want, after independent fixing of the film, the display surface remains clean and without air bubbles, follow the work of the following recommendations.

1. The film or protective glass is better to change in a well-ventilated room, with high levels humidity. This will prevent dust from entering the accessory surface.
2. When you change the protective glass - be extremely neat and not much to prescribe. Otherwise - you can break the fragile detail.
3. If your hands are contaminated - first wash them out, and only then proceed to the procedure for gluing the film (protective glass). Otherwise, fat, ugly traces will remain on the surface of the accessory.
4. If air bubbles were formed under the film, remove them using a medical syringe. Just thread under the accessory of its "Nose" and pump out the air. In essence, the syringe will perform the function of the pump.
5. To remove excess dust from the film (glass), use a special Dust REMOVER tool.

So, now you know how to properly remove air bubbles from under glass (film) on the display of the smartphone. If you adhere to the recommendations described above, the film will fix on the screen exactly, without folds and bubbles. The above councils will help you give your gadget stylish and presentable look.

According to the manufacturers, the displays of modern smartphones are protected by glass, extremely resistant to scratches and damage. Gorilla Glass. - The most popular of these glasses, installed in most medium and high phones price segmentBut even it does not always save the display from damage. In order to ensure maximum protection, it is most often used or shockproof windows, less often - liquid protection, like , as in the picture below.

If when installing a film or Nano Liquid, problems, as a rule, does not occur, then with a sticker of protective glass, certain difficulties may occur. This is especially true for the glass sticker on the phone with rounded edges, the so-called 2,5d. In this case, on the edges of the glass often forms an uncrossed band, which is very spoil appearance phone Below I will tell you what ways you can get rid of it.

What to do if the glass was not glued at the edges

And so, you stuck glass, and at the edges it turned out such a disgrace:

In this case, it phone Xiaomi. Redmi Note 4X. Let's try to fix the shoals.

I know two ways - one handicraft, if you can say so, and one industrial (no more suitable word found).

# 1 first way

Chinese craftsmen do not sit folded and invent all sorts of things that make our lives facilitate our lives. To solve the problem, if the glass is not glued at the edges, in the subway, they created a special means. It is called Border Liquid or something so and is a transparent gel, which, with the help of a tassel, it is necessary to wipe the edge of the glass.

And a small video, how to use all this:

# 2 second way

If there is no money for a miracle for a miracle or simply do not want to wait until it arrives from China, you can use undergraduate tools.

We will need: napkin, thin brush and some vegetable oil or glycerin.

Carefully apply glycerin to the edge of the glass, following it to get into the joint and filled the existing emptiness. At the end of the surplus, remove the napkin. The smaller the width of the white non-flimsy band initially, the better the final result will be.

It's the very simple ways Solve the problem if the glass is not glued at the edges. Try, unsubscribe about the results in the comments.