The other day after unsuccessful firmware Dispenser ASUS RT-G32 (VER. C1) The device completely refused to work. It was impossible to even enter the device control page (I mean addresses 192.168.0.1 or 192.168.2.1 ). Tips on the forums on the restoration of the factory firmware using the program tFTPD32. did not help. Honestly, I began to fear that Wai-Faya I will not have and already began to astrase it in the mind that it is more profitable to give my asus to the workshop or buy a new network distributor. However, the position of the guide from one foreign setup (the link will be below) - I will transfer the sequence of actions in Russian.

Note before starting - you will need about. from. Windows to perform these actions; for LinuxUnfortunately, there is no manual.
No Wireless Device In recovery Mode. IS FOUND, no device is found in recovery mode, ASUS RT-G32 VER firmware. C1, ASUS Firmware Restoration, ASUS 2.0.3.4 Firmware, Router, Router, WiFi, Wi-Fi

So:

1. Download the archive with the Recovery Program ASUS Firmware Restoration. and manufacturer firmware ASUS_2.0.3.4. (Updated by October 17, 2015):

2. Remove the contents of the archive, say on the desktop;

3. Then connect the device directly to the network card - one end of the network stranded (cable) Connect to a computer, and the other to the connector LAN1. router (modem, if available, turn off);

4. Enter the Network Management Center and common access (icon in TRE):

5. Click "Changing the Adapter Parameters":

6. Disconnect all interfaces except "Connections by local network» (Lan.):

7. Open interface properties Lan.:

9. Disconnect network screen Windows in the control panel (as shown in the picture), as well as third party network screens (Kaspersky, Komodo, Outpost, Avast, NOD32 ...):

The first part of the preparation was performed, and now - the second, the restoration itself:

10. Run the program Rescue.exe. From the archive unpacked first and specify the path to the firmware file RT-G32.C1_2.0.3.4.trx, but IN NO CASE Do not press the button " Download":

11. Check again, whether all the wires (cables) are disabled (including the power wire). There must be only a network multi-minor connecting the connector LAN1. router and nest network card computer;

12. Click toothpick or pen ballpoint knobs button Reset. - Hold and hold while you do not let go:

i took this picture from the page

ASUS is a well-proven electronics manufacturer with good characteristics, including modems for Internet access. But any device of this type is required to configure the parameters of the provider, with which a contract for the provision of communication services is concluded.

This instruction will give you the answer to the question of how to configure the ASUS RT G32 router, it should be remembered that the configuration algorithm and the device interface from one supplier are very similar, so the article will be useful to all the buyers of ASUS modems with Wi-Fi.

Preparation for configuration

Technical preparation of the router to the setting is performed in several stages:

1. Connect to Asus RT-G32 power supply and turn it on the power supply network.
2. In the modem connector with the inscription "WAN", connect the Ethernet cable provided by the provider.
3. The port of the router with the inscription "LAN1" Connect with a computer network card using an Ethernet cable that is present in the Wi-Fi modem.
4. Reset the ASUS RT G32 settings to the factory by pressing and retention for ten seconds recessed in the "Reset" button.

Computer settings

Often the computer network card features are manually configured for other connections. To work with Wi-Fi Router Asus RT G32 you need to configure the card:

1. Open the section network settings OS. For example, for Windows 7, you need to open the settings window specified in the following figure (located in the control panel) where to click on the selected link.

2. Go to the connection properties by clicking the PCM by its icon and select the appropriate menu item.

3. Open the "Properties" of the item indicated in the following Figure:

4. Set the values \u200b\u200bof the characteristics of the protocol, as indicated in Figure:

We repeat the procedure for other connections if they are available.

Setting up router

To configure Asus RT-G32 under the settings of your provider, follow the steps of the following instructions:
1. Run any browser, make the address 192.168.1.1 and go through it.
2. In the uploaded authorization dialog in both fields, specify "admin" and click on "send"

3. Click on the "Home Page" button

4. Wai Fi Fi Router Asus RT G32 supports Russian, select it in the "Language" field.

5. To configure the access options to the global network, click on the "WAN" main menu item.
6. Find out the connection type from your telecom operator.

7. If the provider provides the Internet using a dynamic IP technology, then nothing is required on the WAN page. Click on the "Accept" button.
8. If the Internet is provided by Static IP technology, then in the WAN Connection Type item, select the appropriate type and fill in the data obtained from the provider, all form fields and click on "Accept".

9. If you select a PPPoE connection, specify the receipt of the IP address automatically or fill in the address field if it was provided by the Internet provider. Z. akill section of the section "Settings account and connections »Data specified in the contract for the provision of communication services, and in the MTU field, make a value of 1472 and click on" Accept ".

11. Apply the changes and configure the WiFi module for wireless connection. If this option is not needed, restart the modem and use the Internet.

Wi-Fi Setup

To adjust the characteristics wireless access in global Network Open the Wireless Network Menu tab. Where to set the following parameters:

1. In the "SSID" field, you will enable the name of the Wi-Fi network display displayed on the subscriber devices. It can be arbitrary, but should consist only of figures, signs and letters of the Latin alphabet.
2. Turn on the "Hide SSID" option If you want to use this method of protecting your wiFi network from unauthorized access. When activated, the configuration hides your network from subscribers, and you can connect to it only the knowing accurate name.
3. In the "Authentication method" row, install "WPA-Personal". And in the "WPA Encryption" row, select "TKIP". These are the most well-proven and widely used network protection.
4. The WPA Preliminary Wrench line contains a password that users must enter when authorized in your WiFi network. The length of the code combination must be at least eight characters, it is allowed to use any signs.
5. To fix the settings, click "Apply".

On this setting asus RT G32 is over, it remains only to restart it and use the Internet as wired interfaceand on Wi-Fi.

Found a typo? Highlight the text and press Ctrl + Enter

Meet this ASUS RT-G32 version C1, which was tested by Russian providers (although I believe in it with difficulty). In any case, I do not advise this router, since with the standard firmware it is extremely stable and very slow.

But I somehow got it. One beautiful day, I brought this router and asked something to do something to be normal, smiling, I said that I could try to put a DD-WRT, but I would not guarantee stable work, as it is a budget apparatus that is not cost to use how the SOHO solution.

Looking at him attentively, I remembered something .. was the distant 2011, we worked as operators in technical support, and we survived as ...

Preface

And we survived only by the fact that the Internet was banned on our service PC. But we are smart, not a finger of Dela, and we began to practice the use of personal laptops in the workplace in the evening, and as a router, to distribute this internet, used it. But since some "collections" loved to use torrents, the speed of our Internet was extremely disgusting.
Blocking this "collection" on the router and sent it to where, it was decided to put something stable on this router, and the choice fell on the Wive-NG-RTNL. Then it was written an article (at least there is a revision B1).

Is it exactly C1?

as you might notice, this is already the second article about this piece of iron, but in the previous, old article is a revision of B1, and we have a revision C1.

Now, reader, take your router in hand, and look at the sticker: if there is a record H / W Ver.: C1, then you can continue reading this article , if there is something else there, or this record is simply not - close this article!

It is important because the router may fail! But if everything is fine and everything converges - continue.

Description

Well, now let's talk about the firmware of this device.

Why not DD-WRT? Since this router runs on the basis of the RALINK RT3050F chip, just go to DD-WRT.com and it will not work for a firmware, since it is simply no (although I tried). Someone can say that its firmware is possible, but if the official developer DD-WRT said it is impossible, it means that there were reasons.

What is Wife-NG? Wive-NG is a series of open firmware for devices on various chips from various vendors. If you compare this firmware with a DD-WRT, then DD-WRT is a firmware that opens a lot of functional, and Wive-NG focuses on stable operation in maintenance-free mode, while maintaining maximum flexibility and functionality.

Why change the firmware? Well, everything is simple. If you, the reader, arranges the work of your router - do not touch him and close this article. If you have to regularly reboot this router, or you experience difficulties, and you have no money for Microtik, and the game in Dota only adds seats in your beard, then the last chance is the firmware of this router.

Firmware of this router

Immediately to the case:

As a result, we got an absolutely different router :)

I will not dwell on the settings in detail, since I have already written a lot of guidelines, how to do it for any provider (links below). Just keep in mind, the password and login to the admin panel has changed to Admin / Admin (with a capital letter).

If you recently become the owner of the ASUS RT G32 router and faced with those or other problems during its connection and configuration, then you came to the right site. In this article we will consider the most frequent problemsWith which you have to meet when configuring this router, as well as tell about some receptions of operation.

To begin, it is necessary to know the following configuration features from the provider, which will be entered directly when setting up: Protocol (PPTP, L2TP, PPPoE), IP properties (static or dynamic, automatic or manual assignment of IP and DNS), as well as availability (or absence) Binding a network card on the MAC address. It also does not prevent to know if special login and password are installed on the entrance to the router control panel.

In the next step, our path lies in the properties of the local network connection. (Control Panel - Network Management Center and Common Access - Our Internet Connection - Click on it with the left mouse button - Properties). We are looking for "Internet protocol version 4 (TCP / IPv4), click on" Properties ". Press in the" General "tab to get an IP address automatically" and "get the address of the DNS server automatically". Press "OK".

At this point, you must already have an Ethernet cable from the computer to the router, in the LAN connector 1. It is recommended to reset the settings before the first setup - it is done very easily: by 10 seconds you climb the RESET button for 10 seconds.

The site will require authentication - login and password. If any specific data is installed by your provider, then fit standard - admin in login and admin per password. Also information on the login and password from the router control panel can be found on the bottom of the router.

After all operations, we get. First of all, specify the protocol of your operator on the "WAN" tab in the WAN-Connection Type line. If the address is provided automatically - we leave everything as it is. If the IP address and DNS need to be prescribed manually, then put the checkbox on the "no" in "Get the WAN IP address automatically?" And below fit the parameters.

Setting the main part is completed. Now - setting up WiFi. This "Wireless Network" tab is "common."

• SSID - the name of your router;
• Hide SSID - Do I need to display the name of the router or not;
• Country code - choose your country;
• Mode wireless network, Channel width - leave as it is;
• Channel - It is advisable to put any other than automatic or first - optimally 6 or 9. This setting will help you speed up the wireless Internet connection;
• Extended channel - leave as it is;
• Authentication method - WEP, WPA or WPA2. The most modern is WPA2, so we put it. The remaining settings are default.

You can also register your own password in the WPA Preview key. On this page, all - you can click "Apply".

Now we go to "Administration", where we press "reboot" and "output". The router will be fully ready for operation after rebooting.

That's all we wanted to tell you about setting up the router of this model. If you have any questions left - ask them in the comments and we will answer them. See you on the pages of our site!

For the holiday Balloons are inexpensive Auchan.