How to reconfigure the modem D LINK. Proper configuration of the "Rostelecom" modem: ADSL, DSL, D-LNIK, TP-LINK. DSL router firmware update

Many users have an ADSL modem. But not everyone knows that this device can be not only a "adapter" between the computer and the telephone line. If the modem is equipped with the LAN port and is connected to a computer with an Ethernet cable, most likely such a device can perform the functions of the router. How to set up modem as a router - we will look here.

Modem with LAN port

ADSL modem can work in one of the modes: "Bridge" or "Router". The second option is good because it is possible to connect not one computer to the modem (that is, to the router), but a lot. True, for this you have to use a switch. Even, you can directly connect the Wi-Fi access point directly, and get a wireless network.

Routher and Modem Connection Scheme

To connect an external IPTV-console, you need an additional LAN port (so buy a switch - you still have to). You can watch IP-TV via the computer, but for this it will be necessary to switch the modem into the "Router" mode (and then, configure the additional connection interface in it). Said about IPTV - True for most ADSL providers, including Rostelecom.

Configure a modem in router mode

How to go to the Web interface?

On the sticker or in the instructions - the value of the IP address of the graphical interface of the modem must be specified. First we try to get into it without performing a reset of settings.

The LAN modem connector - connect to the computer, as shown:

Modem Connection Scheme to PC

The network card is configured as follows:

IP address - Anyone belonging to the range of modem addresses
Gateway address is equal to an IP modem address (or web-interface address)
The mask of the network is set "with the last zero" (give an example):

Setting up a network card

If, after checking multiple address values, it became clear that the login cannot be logged, give a single tip: you need to reset the modem settings. After a minute or later, after turning on the power of the modem, you press the RESET button on the housing (holding it 10-15 seconds).

It is important to know that you can perform a reset only if VPI and VCI parameter values \u200b\u200bare known to further configure the connection. Otherwise, it will not be possible to configure the modem even "as it was."

After reset to any modem, you can connect, configuring the network card on the "Auto" IP and DNS. Sequence - Such: Reset, Setting up a network card, reboot PC.

Customize the connection in the modem router

How to configure the modem into the router mode, we consider on the example of the D-Link DSL-2500U BRU device. When entering the interface, inform the username and password of the administrator (word admin):

Main interface tab

You will need to delete "unnecessary" connection interfaces (using "Remove"), and click "Add":

Setting up a new compound

Please note: if on the second page - to specify instead of "PPPOE" "Bridging" mode, then we get a modem working in the "Bridge" mode. The setup is reduced to the installation of the connection parameters followed by clicking "Next".

PPPOE connections:

VPI and VCI values \u200b\u200bfor the Internet channel
Encapsulation mode (usually - LLC)
Subscriber Name and Password
"Static" IP (only in case of use)

Install the Keep Alive checkbox if you need to get a connection running constantly. The option "NAT" and "Firewall" must be used necessarily (and "IGMP" - only in the case of the transfer of IPTV to the IPTV provider, moreover, one channel together with the Internet). "Wan Service" - you should always use. At the last stage, click "Apply" (and then "Finish"). Successful setting.

Additional features available in Router mode

IPTV, option VoIP and others

Router mode is good because you can configure multiple connection interfaces with the provider (one, PPPoE is the Internet channel). Rostelecom, for example, on a separate channel transmits IPTV. Also, additional interfaces are used to use the VoIP option or some others:

Multiple connection interfaces

Please note that VCI / VPI values \u200b\u200bfor each of the interfaces are different. The second and subsequent connections can be configured in the "Bridge" mode. In some modems, it is additionally necessary to indicate that the main connection gateway is the PPPoE interface:

Configuring D-Link Modems, "New" Graphic Interface

If LAN ports are provided by several, you still need to "bridge" a bridge interface with one of the ports. Explore the instructions on the modem (if the LAN port is one, you will not need to perform this setting).

Connection Modes in Router

"Keep Alive" - \u200b\u200bpermanently enabled (it is "Always ON"), this mode is recommended to use
"Dial On Demand" - auto-connection when accessing Internet resources (shutdown occurs after the set time after the transfer is completed)
"Manual Connection" - Connect / Disable Connection through the tab (usually, basic) in the Web interface

How to configure the Internet connection in the D-Link modem with a new graphical interface option - is shown in the movie (Router mode, without IPTV):

ADSL modem is used to install an Internet connection using a telephone line. It can be used as a router or a bridge, and most modern models are equipped with Wi-Fi feature. Users who first encountered with the configuration of this device may experience some difficulties, since all parameters need to be specified manually.

AdSL modem setting

The easiest way to acquire modems, which includes the installation disk. After it starts, the settings are defined automatically. If the disk drive is missing, the parameters will be required independently. This article will step by step to describe the technique of working with ADSL modem.

Step 1: Resetting the settings

In most situations, it is much easier to roll back the parameters to factory, than to change each item in the settings separately. This is mainly related to devices that have already been used to connect to the Internet. To restore the settings to factory, follow these steps:

Thus, you can quickly roll back the settings. The method is universal for the modems of most manufacturers.

Step 2: Connecting the device to a PC and network

Before changing the ADSL modem parameters, it is necessary to connect it to a computer and network. To do this, you need to have a splitter, an Internet cable and equipped with connector, telephone cable. Connection is done in this way:

Step 3: Set the connection parameters

Change the connection settings is the easiest way through the web interface. To open it, you must enter any browser IP address in the search bar. You can find it in the instructions.

If the address is specified correctly, the interface does not open up, most likely, the device was incorrectly connected. Check the cables and try again. If no change occurred, and the transition to the router page does not all be done, it is necessary to change the parameters of the network card. To do this, follow these actions:

Here you can reset the settings. This is done in this way:

Open the System section and go to the configuration unit.
Click on "Factory Settings".

Step 4: AdSL Modem Setup

Usually, the parameters are determined automatically, but if this does not happen, you will need to set up manually. The instruction may differ somewhat depending on the device being used and the device brand, but the general configuration steps are similar for all models.

After opening the web interface, go to the "NET" section.
Go to the "Connections" tab and click on "Add".
Now it is necessary to fill all the empty fields in the most detail, the values \u200b\u200bfor each item will be below:
- Connection type - PPPoE;
- VPI and PCI - information is specified by the provider;
- The username and password are indicated individually.
In addition, it is necessary to put a tick opposite Keep Alive and IgMP items. It is also desirable to specify intervals and failures. They are needed to determine the frequency of requests. For an unstable connection, it is better to specify the minimum parameter of the interval.
Confirm the changes made by clicking on the "Save" button.
Now it remains only to restart the device so that new parameters entered into force.

Some devices have the "Quick Settings" feature. It helps to set the correct configurations automatically.

Step 5: Connecting a modem to a router

The procedure for connecting this equipment is quite simple. It is carried out in this way:

First of all, you need to configure the DSL device. This is required in order to have a network connection.
Connect the Internet cable from the router to the corresponding jack (LAN) (WAN slot). After that, it is recommended to reset the router parameters to factory settings.
Connect the router to the computer and go to the router page.
Go to the "WAN" section and opposite the connection type item, specify the "Dynamic IP" option.
Now you need to set the PPPOE parameter and enter data for authorization (username and password).
It remains only to save the changes, and re-activate the device.

Usually these actions are enough to connect. If no visible changes happened, contact the operator for help. You may need to use some special configurations.

Step 6: IPTV Configurations

ADSL modem can be used to work with IPTV. To do this, you need to create a bridge and perform the correct setting. The procedure is as follows:

Go to the web page and go to the "Connections" tab.
Put the BRIDGE connection type, then configure VPI / VPI.
Save the changes made and go to the "Advanced" section.
Go to the "Interface Grouping" section and click on the inscription "Create a group", then assign it the name.
It remains to move the lan-port and the bridge to the column on the right, after which save the settings, and re-run the device.

Now IPTV will function on the specified connector.

With the help of ADSL modems, it is very convenient to work through the telephone line, but their setting is very complex for novice users. Try to adhere to the instructions as accurately as much as possible and do not be afraid to seek advice from providers, they must provide you with all the information you need to configure.

Not everyone needs complex network devices that have a maximum set of functions "in one case". Sometimes, it is wiser to create a home network, adding the necessary components step by step. It is for such cases that the router D Link DSL 2500U is intended, which will correctly name the ADSL modem capable of working in the router mode.

ADSL Router model DSL 2500U

The presence of the ADSL + module implies that the user receives the Internet on the telephone wire. From the standard router built on the principle of "all in one", the DSL 2500U router is distinguished by the absence of a wireless network module, and is just one LAN port. Just to this port through the patch cord, you can connect a computer (including for configuring the device), or a switch, an access point, and the like. Nevertheless, more convenient for the user would have two such ports, one of which would be used to configure.

Setting the basic functions of the router

Connection before setting

Complete with the device - there is a network cable called patch cord. The LAN port is connected to this cable with a PC network card connector. Then, the telephone wire is connected:

Routher Connection Scheme

Last but you can feed meals. Before this - we recommend to configure the wired connection in the computer:

Setup PC Network Card

That is, the computer must receive IP, mask and DNS automatically. After turning on the power of the router, you need to wait 1-2 minutes. The device will boot, and you can enter the configuration interface from the browser.

Authorization in the graphical interface

Setting up the router D LINK 2500U occurs in the graphical interface. To go to it, it is enough to open the browser, and go to the address: 192.168.1.1.

As a login and password, the ADMIN pair should be approached. Clicking "OK", the user must see the following:

Auto tuning tab

To configure the Internet connection, you need to click the WAN button.

On the Home tab -\u003e "WAN" to configure the connection - click the "Add" button:

Connection Settings Tab

Before you configure anything, you need to learn all the necessary parameters, including those related to the Internet connection. For the PPPOE protocol with a dynamic IP address, it must be values:

VCI, VPI (usually 30 and 1, or 32 and 0, etc.);
names of the subscriber name and password;
it is necessary to specify which protocol is used ("PPPOE LLC" is the most common option).

On the tab that opens after clicking on the "Add" tab, set the VPI and VCI values \u200b\u200b(and click "Next"):

It is important to know that in addition to the "LLC PPPOE" provider can use another option. If this is the case, you need to select the desired value from the "Encapsulation Mode" list (by default, LLC is installed). Then, click "Next":

Installation and Password Installation Tab

Install the password and the subscriber name here, as well as the Keep Alive checkbox. By clicking "Next", there will be two ticks:

IGMP item must be selected if IPTV is planned. Click "Next" and see the final tab:

Tab, which shows the result of the setup

Here you need to click "Apply", and before the user - the Home tab appears -\u003e "WAN" tab. In addition to the "Add" and "Finish" buttons, it has the "Remove" button. And you need to click still "finish", after which the router will remember the settings and will reboot.

On the presence of connections can be found on the "Status" tab -\u003e "Wan Info" (ADSL Link Up) appears. We looked at how the DSL 2500U router is configured to connect "PPPOE" with a dynamic IP address. If the address is static, then on the setting tab of the name and password, you must select the appropriate option (and set the address value).

The "Home" -\u003e "LAN" tab allows you to change the local address of the router (graphic interface address) and configure the DHCP server. By default, it is turned on, and distributes addresses in the following range:

Local Settings Tab

Note here the presence of one important setting. If it is necessary that the router passes the multicast packets (used in IPTV), it is necessary to mark the "IGMP Snooping" checkbox. The settings will take effect only after pressing "Save / Reboot". We wish you success.

Using additional options

Setup IPTV.

Considering the connection setting, as well as the local network, we said that the router would "skip" multicast packages. To view IPTV through a computer - this will be enough.

ADSL Router DSL 2500U, like any other modem or ADSL router, has a high packet switching speed. That allows you to transmit even the FullHD stream. Quality - depends rather from the provider.

Turning on UPNP

UPNP protocol on the local network - you can enable if on the "Home" -\u003e "LAN" tab, mark the appropriate check mark. It is called "Enable Upnp".

It is desirable to use this option if UTorrent, Scype, ICQ programs are used in which UPNP support is enabled. Additionally, we note that without UPNP on the local network - some models of NAS-drives may not work. At the same time, the UPNP protocol does not slow down the work of other programs.

Installing DNS explicitly

By default, the device is configured so that it receives DNS automatically. You can manually set the DNS servers addresses for which you need to go to the "Home" tab -\u003e "DNS" tab (Note that the Dynamic DNS tab is not used):

After removing the tick, the user will see that two fields appeared (they need to be filled). In the completion of the setting, it is enough to click "Apply" - the router will use the set values.

Automatic receiving DNS slows down the device operation. At the same time, this setting is more reliable (because the DNS server can change). Selection - for the user.

Free access has video to configure the connection:

This article is devoted to connecting and configuring the D Link 2640U modem. Here you will find a full step-by-step instruction, learn how to connect a router through a router, how to organize a secure and encrypted PC network Wi-Fi network, as well as network parameters for different providers.

Modem Connection

In this section, we will look at how to connect a modem to a computer.

First of all, the router should be connected to the power - insert the end of the wire from the power supply to the appropriate slot on the back of the modem, and the power supply itself is in the outlet.

On the back of your modem (router), there are 4 LAN inputs at once, it is there to insert one of the ends of the blue wire, which is included with the D-Link 2640U, and insert the other end to the LAN port on your PCM.

At the same time, be careful: LAN light should be outline on your router with the modem port number in which you inserted a local wire. At the same time, both ends of the wire must be in their places (the port on the PC and the port on the router).

After that, go to the next tab of the instructions, where you will be asked to connect your modem and splitter. Included with the modem there is another cable - insert it into your splitter (separator), and put the other end of this cable to the appropriate port of your router - "Line".

Factory settings

Each device has its own "factory settings". On how to reset the D-Link 2640U settings to factory, and goes on speech. Reset settings to factory items fall if you simply fail to go to the modem settings menu, or the modem setting was incorrect.

The "Reset" function is on each router and take advantage of it much easier than you think:

find a needle at home or Shilo, look at the rear panel of your router, where you will see a small hole signed by the word "reset";
it is it: insert a needle there (match), wait about 5-6 seconds. In this case, the router must be included;
after this time, all the light bulbs on the router one by one will go out. It can restart, which means that the modem settings are reset to factory. Now you know how to reset the settingsD-Link 2640U.

Video: Routher Setup D-Link 2640U

Login via VEB - Management

Each modem has its own WEB-control system. In the case of the D-LINK 2640U router, you can go to it through any browser on your computer.

check if the modem is connected to the computer and splitter (Line and LAN lights should be lit);
after that, open the browser (Opera, Chrome) and enter the IP address 192.168.1.1. You will find yourself in the WEB-Management window, where you can update your modem and make it setting in automatic or manual mode.

Update firmware

In the section we will tell you how to correctly update the firmware of your router. After purchasing each device, we advise you to check the latest firmware (updates), which will ensure the reliability of its work for a longer period of time.

AdSL parameters Connection

The ADSL connection parameters are very important, because they will depend on them as the speed of your Internet connection and its smooth operation.

As described earlier, go to the VEB control panel of your modem:

opening the browser, enter 192.168.1.1 in the address bar. Enter your username and password (default Admin / Admin) and press the input button;
click on the "Network" tab, in the WAN section. If the router is only purchased, all connections should be removed. Use the "Delete" button for this;
next, click on the "Add" button and enter your Internet connection settings;
and then proceed according to the instructions below, because the parameters of the ADSL connections are directly dependent on your Internet provider.

How to set up a D-Link 2640U router for providers

To connect the D-Link 2640U router, you need to connect the router itself to the computer first.

If you do not have a signal separation, when you need simultaneous work and phone, and the Internet, then do the following:

Rostelecom

open the browser, enter in the address bar 192.168.1.1 and press ENTER /;
enter your username and password (default - admin / admin) and press the input button;
go to the "Network" tab, and from there to the "WAN" section. Clean all Internet connections using the Delete button.

Click on the Add button and enter the following options:

Domolink

Specify the following parameters:

VPI \u003d 0;
Vci \u003d 35;
pPPOE type;
next, fill out your username and password (Password) obtained from the provider when the connection is made;
put a tick "Keep Alive".

The rest of the pages simply skip the Next button and confirm the apply settings. Press the FINISH button and thus complete the router setting. After a couple of minutes, the connection will be installed.

MGTS

Ukrtelecom

Go to the settings menu of your router via WEB - control. And for this in the browser, enter 192.168.1.1 and click on ENTER. Enter the login and password, click on the Login command.

Remove the checkbox with the DSL Auto-Connect, then proceed to setting up the modem:

Save and wait about a minute until the router reboots.

Modem Setup in Routher Mode

The modem can be configured both in the router mode and in the Bridge mode. To configure the modem in the router mode, open the WEB - control panel. To do this, open the browser and enter in the address bar 192.168.1.1. Enter your username and password (default - admin / admin), enter the panel and go to WAN settings. Now it will be necessary to fill out the network settings that you can learn from your provider, or read in the sections above.

Wi-Fi Network

Go to the WEB - Control Panel of your router:

Continue setting up WiFi, you can now enter your network security settings:

In the article, we looked at all options for configuring the D-Link DSL-2640U router from connecting it to power and your PC, before the settings of the Internet parameters for different providers. We hope our article was able to fully disclose the answers to your questions.

Internet - Provider Rostelecom occupies one of the first places on the number of subscribers using its services. The company provides - connecting the Internet, telephony and television. When concluding a contract for the provision of communication services with Rostelecom, the client can immediately purchase the appropriate equipment. And experts will install modem Rostelecom, and configure it to stable work. The value of the modem is from 1890 rubles to 6200 rubles, depending on the brand and model. For the installation of the technique usually do not take an additional fee. But if the subscriber did not have the opportunity to use the services of specialists, and he wants to independently connect and set up a modem Rostelecom, it will help him a small and quite understandable instruction described below.

Before starting work, it is necessary to figure out what is an ADSL technology, and what principle it works.

A feature of the ADSL Internet technology Rostelecom is the establishment of communication on telephone wires. What makes it available, even for remote corners of the country. Connect the Internet from the telephone cable is much easier than pulling, for example, fiber. The technology system is asynchronous data transmission. In this case, the speed of information received is much higher than transmitted.

An important point when connecting the Internet using ADSL technology is the acquisition and connection to a special splitter line. With which, the signal to the phone will not be interrupted when the Internet is on, and vice versa. It is a small box, which includes telephone wires, and the output is branched to several possible connections.

The company provides 5 stamps of routers:

D-Link.
Sagem. [Email Protected]
QTech.
TP-LINK.

The principle of operation, and install the necessary parameters for the connection, they do not differ significantly. Therefore, to understand how to configure the modem Rostelecom ADSL technology, the principle of operation will be considered on the example of the QTECH QDSL-1040WU router.

Requirements for computer

Rostelecom routers may not work on old PCs. To ensure that the connection is carried out without failures, experts recommend using computers that meet the following requirements:

operating system - Vista, XP, Windows 7 and above;
included automatic update system;
updated browser (Internet Explorer 7, Yandex, Google Chrome);
volume of free RAM at least 256 MB for Windows XP, 1024 MB for Vista and Windows 7;
the presence of a network card.

Connection scheme

Before you start changing settings, and connect to a global network, you must connect a modem for a rostelecom with a computer and a telephone line.

Connection diagram:

Connect the Rostelecom modem using the wire through the telephone splitter.
Connect a PC with a modem LAN cable.
Enable the power cable device into the outlet.

After all actions, the router indicators must be filled with red or green. What light bulbs burn on the device with the correct connection of the modem Rostelecom can be clarified on the manufacturer's website. If the lamps are not lit, you should check all the equipment for damage, and, if necessary, replace faulty.

Further user actions should be aimed at setting up Equipment Rostelecom on ADSL technology.

Methods setup

Currently, Rostelecom subscribers are available two ways to configure ADSL modem:

Automatic.
Manual.

Both options do not take much time, and do not require great effort. The main thing follows the instructions, and correctly indicate important parameters.

But before starting work, the user needs to check whether the device drivers installed on the computer in automatic mode. Since without them, the computer will not be able to connect to the modem. You can see the drivers in the Device Manager. In the absence of settings, the name of the router will be labeled with a yellow exclamation mark.

If the drivers are not installed, they need to be downloaded independently. This is done with a disk that is included with the device. If there is no media, or it is not in good condition, you will need to download important files from the manufacturer's official website.

Automatic setting

Set up the modem Rostelecom in automatic mode is simple enough. To do this, you need to insert a disc that walked complete with the equipment into a computer drive. Start the "Setup Wizard" program installed on it. And follow the system prompts that pop up on the PC screen.

If the disk is lost, or is defective to download the wizard utility from the Internet. The program is provided free of charge.

After all the settings, the Internet connection will be automatically configured. The user will only remain open any of the installed browsers and check the performance.

Manual setting

Manual configuration ADSL Modem Rostelecom takes a little longer. And requires a subscriber of care when entering data.

Stages of change of modem parameters Rostelecom (on the example of QTECH QDSL-1040WU).

Open the browser installed on the PC to configure the Rostelecom modem.
In the line for entering the address Write - 192.168.1.1.
Press "ENTER".
In the window that appears, enter the username and password of the subscriber (they are listed on the rear panel of the device). For QTech Modem, this is admin - in both cases. If standard data is not suitable, you must reset the modem settings using the "Reset button located on the device housing. Since it is a little recessed inside, in order to avoid accidental clicking, an ordinary stationery clip or a rod from a ballpoint handle can come to the aid of the client.
Now you need to change the connection settings. To do this, in the left side menu, select "Advanced Setup", and click "Add".
Specify (they depend on the connection region).
Confirm the actions by the Save (Save) command.