Does not open the settings of the router 192.168 0.1. How to open a Wi-Fi router settings (log in to the web interface). What to do if the page with the settings does not open. Discovered power of the router or a problem with a network cable

In general, this address is used to enter the settings on most routers and modems. The reasons why the browser does not enter the settings located at this address - really quite a lot, I want to consider the main of them in this article.

And so, let's go ...

First check the address if you copied it correctly? (just below is highlighted in blue)

1) Incorrect browser settings

Most often, the problem with the browser occurs if you are turned on turbo mode (This is in Opera or Yandex Browser), or a similar function in other programs.

Also, check the computer for viruses, sometimes, the browser can be infected with a virus (or addition, some bar), which will block access to some pages.

2) turned off router / modem

Very often, users try to go to the router settings (or modem), and the device itself is turned off. Be sure to check that the light bulbs (LEDs) flashed on the housing, the device was connected to the network and power supply.

After that, you can try to reset the router. To do this, locate the reset button (usually on the rear panel of the device, next to the power input) - and hush it with the handle or pencil for a while 30-40 seconds. After that, turn on the update - the settings will be returned to the default settings and you can easily go to them. (How to go to the router settings

3) Network Card Settings

There are a lot of problems due to the fact that the network card is not connected, or does not work. To find out if the network card is connected (and is enabled) - you need to go to the network settings: Control Panel and Internet Connections

For Windows 7, 8, you can quickly get into the settings if you press the Win + R buttons and enter the NCPA.CPL command (then click on ENTER).

Next, carefully look at the network connection to which your computer is connected. For example, if you have a router and a laptop, then most likely the laptop will be connected via Wi-Fi (wireless connection). Press it right-click and click Enable (if the wireless connection is displayed with a gray icon, not color).

By the way, you may not be able to turn on the network connection - because Your system may miss the driver. I recommend that problems with the network, in any case try to update them. About how to do this, see this article: "How to update the drivers."

Important!

Check required to set up a network card. It is possible that you have the address of the settings not 192.168.1.1, and the other. To do this, go to the command line (for Windows 7.8 - click on Win + R, and enter the CMD command, then click the Enter key).

In the command prompt, enter a simple command: ipconfig and press ENTER.

After that, you will see many parameters of your network adapters. Pay attention to the "Main Gateway" line - this is the address, it is possible that you will not have 192.168.1.1.

Attention! Note that the page of the router settings in different models is different! For example, to set up Trendnet routers need to go to 192.168.10.1, and ZyXEL - 192.168.1.1/ (see the sign below).

Table of logins and passwords (default).

ROUTERSUS RT-N10ZYXEL KEENETICD-LINK DIR-615APES PAGES RETURS192.168.1.1192.168.1.1192.168.0.168.1192.168.0.1LoginAdminMinadMinPallDmin (or empty field) 1234Admin

4) Antiviruses and Brandmasters

Very often, antiviruses and brandmasters built into them (firewalls) can block some Internet connections. In order not to guess, I would recommend it for a while to disable them: usually enough in the tray (in the corner, next to the clock), right-click the antivirus icon, and click on the output.

In addition, there are built-in brandmauer in Windows in the Windows system, it can also block access. It is recommended to disable it for a while.

In Windows 7, 8 of its settings are located at: The Control Panel and SecurityBrandmaeer Windows.

5) Checking Hosts File

By the way, even more detailed article about the recovery of the HOSTS file -

Hey! I noticed that many problems with the adjustment of routers start before the start of the configuration process itself :). And there is nothing strange here, and the most popular problem is when it does not work, it's easier, there is no access to the settings.

When trying to go to the address 192.168.1.1 (maybe another address, for example, 192.168.0.1) An error appears "Unable to connect to a remote server", or something like that.

Now consider the main reasons through which a similar problem occurs most often and try to fix it.

No address 192.168.1.1 (192.168.0.1), what to do?

Most likely, something is incorrectly connected, or incorrect settings on the computer.

Check the router connection with a computer

I'm writing similar articles, always saying that at the time setting, the router must be connected to a computer (laptop, netbook) on a network cable. As a rule, the cable is included with the router. When you configure everything, the cable can be turned off, everything will work without it.

Turn on the router into the socket and connect it using a power cable to a computer. Usually, the network cable on the router is connected to the yellow connector. Like this:

One of the LAN indicators should be lit on the router.

The computer should also determine that you have connected a router to it. Status should be as follows:

Do not be afraid that the status "without Internet access". You just didn't configure anything yet, it will still be :).

If you have everything connected correctly, then try to go to the address 192.168.1.1. Don `t come in? That misfortune, go on.

Perhaps the laptop has already managed to connect to the Wi-Fi router. Check and disconnect from the wireless network. Connection should be only on the cable.

Check the IP address. Perhaps you have not 192.168.1.1

I definitely do not know how on routers, from other manufacturers, but from the bottom of the router from TP-Link you can see the address to access the settings and password / login, which is used by default to access the control panel.

Take a look at your router, you may see something interesting there and the problem will be solved.

In TP-Link it looks like this:

As you can see on the router TP-LINK TL-MR3220 IP address 192.168.0.1 . And how do not try, and in the settings at 192.168.1.1 not to get.

Check out whether you enter this IP address in the address bar of the browser. You need to enter it precisely in the address bar, and not in the search string :). Sorry, for such children's advice.

At the end, try another browser.

The main reason is not established to receive IP and DNS automatically

This is probably the main reason why you cannot get into the router settings. It was necessary to write it first, well, okay.

So you need to check if you have installed on your computer get IP and DNS automatically. Perhaps with the old connection you have static addresses.

Right-click on the connection status on the notification panel and select "Network and Common Access Control Center".

Go left to the section "Change adapter settings" and right-click on "LAN connection". Choose Properties.

06.06.2015 Alexander Pukhovsky

If you need to configure the modem (router, router), and the browser at 192.168.1.1 does not open the login and password window, as in Figure 1, and instead you see the window, as in Figure 2, or something similar - The technical support service of the Internet provider, as a rule, in this case can not help, and in response you will hear: "Reinstall the network card driver."

In fact, the reasons why in the browser at 192.168.1.1 does not open a window to log in to the modem settings - many, but they are quite realistic to reveal and eliminate themselves.

I will list the most common faults that do not allow you to go to 192.168.1.1 in the router settings:

1. No network card driver.
2. The address to enter the modem settings is incorrect (i.e. it is not 192.168.1.1).
3. NOT prescribed the IP address of the network card.
4. Faulty cable connecting the computer and modem.
5. Faulty modem.
6. Malicious programs (viruses) on the computer.
7. Faulty network card.

Now consider the sequence of identifying and eliminating the above faults.

1. No network card driver

To check the availability of a network card driver, you must log in to the Device Manager and view the "Network Boards" section. It must be like in Figure 3. If a yellow exclamation mark is worth a yellow exclamation mark in a network adapter, it means you need to install a network driver.

2. Address for logging in the modem settings is incorrect (i.e. it is not 192.168.1.1)

Make sure that you are 192.168.1.1 for your router model, and not 192.168.0.1, 192.168.168.0.1, 192.168.100.1 or some other (address 192.168.1.1, as a rule, is used in modems commocate M200A, Huawei, ZTE, TP-LINK companies byFly). To do this, you can call your Internet provider and call your router model (indicated on the label on the bottom of the device). Often the address for logging in settings is indicated on the label next to the router model. You can see in the instructions that you were issued, or on the manufacturer's website.

3. NOT Specified IP Address Network Card

This can be understood on a yellow exclamation icon on the network connection icon in the lower right corner of the screen. In this case, the easiest way to seek help from your Internet provider.

4. Faulty cable connecting the computer and modem

To check the maintenance of the cable, you need another cable :). There are almost everyone from the computer to connect a computer to the modem. Go beyond the cable to your neighbor and try to open the modem settings window using a well-serviceable cable.

5. Faulty modem

To check the modeem, it is necessary to connect it to another computer or laptop, and if after dialing in the address bar 192.168.1.1 will not open the window for logging into the modem settings, then the router is faulty.

6. Malicious programs (viruses) on the computer

If all of the above actions did not give results, then most likely you have a virus on your computer or software failure. You can try to reinstall the network driver or run a utility to search for viruses, and easier to reinstall Windows with drivers.

7. Faulty network card

You reinstalled Windows 7 or 8, installed the necessary drivers, and open the modem setup window to 192.168.1.1, it means that you definitely defects the network card. For computers - an additional network card is installed, a laptop is to repair or an external network card is installed. Now you can accurately at "192.168.1.1" go to the modem settings. It remains in the window that opens, enter the login and password (usually the words "admin" and "admin" respectively), and you are in the modem settings.

On computer forums, a lot of attention is paid to fine tuning the router, which allows you to significantly increase its speed and stability of the connection. However, many users faced a problem of a different order - they simply cannot go to the settings of their router to select the optimal parameters. You don't need to panic and go to the store for the new device, since every person can solve such a problem. If the computer does not enter the standard menu of the router's web client, you need to try to change the connection settings or pay attention to other nuances.

We are looking for an output if there is no access to the router settings.

By typing the address of the web client 192.168.1.1 in the beloved browser, you may encounter the fact that the router does not respond to your team. To enter the web client menu, first take the instructions and read what the address is set to the manufacturer's router. Very many electronics developers prefer to set a combination of 192.168.0.1, which allows you to free the above address for other network equipment. Also, the information about the base address may be contained on the bottom of the instrument housing.

Try to change the web browser - the optimal option gives the standard Internet Explorer application, which uses direct connections without redirecting. However, he may display an error when I am attempted Introduction 192.168.1.1. You can enhance the chances of successfully creating a connection by using the RJ-45 standard cable that is supplied with your router. Be careful - it must be connected to the port of the local network on the router, and not the WAN connector, which is most often highlighted in blue. To get unlimited access to the menu 192.168.0.1, be sure to disconnect the used wireless adapter on the computer using the special function button or the network connections menu.

Thin tuning

If the computer does not enter the standard web client menu, it is possible that the connection error from 192.168.1.1 is caused by the conflict of addresses on the network. First of all, you need to log in to the operating system control panel and find the "Internet Properties" item there, which can also wear the name "Browser Properties". Then you need to open the "Connection" tab and at the bottom to find a button that is responsible for the parameters of the local network. In the dialog box that opens after the dialog box, disable the use of a proxy in ordinary local networks and VPN.

However, establish a connection from 192.168.0.1 is not always obtained. You need to open the properties of the network adapter used - you can enter this menu by three main ways:

• Through the "Network Management Center";
• Through the control panel - the "Network Connections" tool;
• Enter Control NetConnections on the command line.

As the router has a web client address 192.168.1.1 or alternative 192.168.0.1, for the correct operation of the network, the electronic computing machine must have a similar IP, which is extremely the last digit. By right-clicking on the icon of the adapter you need, open its properties, in the dialog box that appears, select the IPv4 connection protocol and click on the "Properties" button.

The general protocol parameters may contain a response, why the computer does not enter the standard menu of the router web client. The IP may differ from which router uses - to continue work, you will need to change it by using the same beginning that in 192.168.1.1 or in 192.168.0.1. Located at the end of the digit should vary within 2-254, so as not to create a conflict of addresses inside the local network. Of course, the optimal option will set the address automatically based on the needs of the computer, but this possibility is not supported by any network. Do not forget to also install the DNS gateway address and server address on this tab - in these fields it will be necessary to enter the numbers 192.168.0.1 or an alternative combination of 192.168.1.1, depending on the standard parameters of the router.

Also, the computer sometimes does not enter the menu desired by you as a result of limiting the transmitted traffic inside the local network created. Open menu 192.168.1.1. It may interfere with the antivirus set by you, which sets too serious control of the user's actions - during operation with the device settings it is worth it simply turn off. Access at the specified address or 192.168.0.1 is often overlapped with a standard operating system firewall - it can also be disabled through the operating system control panel. After executing the above actions, you should have the ability to go to the settings of the router used, but in certain situations all user actions are unsuccessful.

Extreme measures

If the computer still does not enter the device's web client, it is advisable to perform its full reboot - for this, a small RESET button is operated, which can be located behind or at the bottom of the router housing. It must be pressed by a long subtle object (for example, a clip) and hold for about 10-20 seconds, depending on the model of the wireless device. After full data reset, you can access all the advanced device settings at the standard menu address 192.168.0.1, as well as an alternative combination of 192.168.1.1 - this is determined by the instrument model.

The specified method will be effective and in case you have lost irretrievably data to access the web client, or they changed another person who received unauthorized access to the router settings menu. After the reboot is performed, it is necessary to use the standard login and the preset password, which is set by the equipment by linker. Most often in both rows, you need to enter the word "admin", but there are some exceptions. To accurately determine the correct data for logging into a standard web client, view the instructions for the device. Be careful because after rebooting all the settings will have to be installed again.

If, after resetting the router parameters, the computer is not included in the settings menu at the address menu 192.168.0.1 or an alternative IP, try to repeat the attempt using another laptop or a modern tablet. It is possible that the inability to gain access to 192.168.1.1 is caused by improper setup of a network card or damage. In the first case, you should try to recover drivers or use the branded distribution of the operating system from the developer of the smart car. In the second case, you will have to change the wireless module.

The source of your problems may be a malfunction of the router itself - usually the problem of the impossibility of access to 192.168.1.1 is solved by a simple flashing of the wireless device. Remember that entering without interference in the web client menu you can exclusively if you download the software from the proven source - it is best to use a global network resource or a file server of the manufacturer of the router. Also, the router does not enter the standard settings menu by a combination of 192.168.0.1 and with complete breakdown of components. A similar device is always easier and cheaper to change than to repair. When choosing a new device, guide the characteristics of its power and antenna strengthening, as well as the possibility of working with certain types of networks.

If the device is damaged, but you need to create a wireless network for a short time, you can use the appropriate feature of the adapter in the computer. To do this, establish the appropriate software - the Virtual Router Manager will be a good option. After it starts and properly configured the electronic computing machine will independently distribute traffic through a wireless network, although the capabilities of such a connection will be limited. For example, to achieve high speed and a large range of network work will not definitely. In addition, at this time the device will not be able to connect to other wireless networks.

Solution of problems

Statistics provided by service centers shows that in 90% of cases, the problem with the impossibility of access to the web client is managed to solve a simple reunification of the router or computer. Special attention to the user should be paid to network settings - most often the cause of the fault is the conflict of addresses surrounded by a computer. Also, the impossibility of access is often due to the restriction of traffic with antivirus or standard firewall, so such protective applications are advisable to disable before work with the wireless network settings. However, there are also troubles related to the failure of the router software - the device will be rebooting or re-firmware. Finally, the root of the problem is to search for a malfunction of the device itself or a network adapter of the computer - unfortunately, during their breakdown, they will have to acquire new equipment.