How to apply a thermal power to the processor? Detailed instructions and useful recommendations. How to replace the thermal column: simple instruction that will extend the life of the PC where is the thermal paste

The replacement of the thermal paste is the topic of my article that will help you, dear friends, solve one of the most frequently, what do you think, why do you need a replacement of the thermal paste? Outwardly, this tool looks like an ordinary toothpaste, which we see every morning, but it is not created for the oral cavity. The thermalcase provides reliable heat consumption between chips and cooling system. In particular, this substance is applied to the processor.

In general, the paste is ideal for everything that is connected to the radiator. It is applied to various chipsets and bridges on the motherboard. Heat is given to the radiator, and the one, in turn, by means of a fan, displays it for the system. Although, not all radiator designs need it. For modern systems that are endowed with a pair of small coolers, special gaskets should be used. You can also use a heat-conducting paste that allows you to fix the radiator on the heating element. In most cases, the replacement of the thermal paste is required processor or video card. This is why my today's post is dedicated.

Stage of preparation

So, before removing the radiator and squeeze just a bought tube on the chip, required. After that, once again run the "car" if the problem with the performance and overheating did not disappear, then you have to resort to the replacement of the thermal paste.

Thus, the replacement of the thermal paste is the last measure that should help. If you are not enough technical skills, I recommend contacting the "advanced" guys from the service center or pass the device to the warranty service item. Our procedure is actually very simple. All that you need to disassemble the systemist, remove the cooling system and apply a thin layer of pasta to the surface of the processor. That's all. It is easier than it seems.

Why do we need a thermalcaste?

To answer this question, I suggest to go deep into the essence of the problem. The heated air is given by contacting a certain element and radiator. Moreover, both devices must be tight pressed to each other. How can one achieve such an effect. You can, as it should, polish both surfaces, but this will take a lot of time and strength. At the same time, manufacturers risk spending too many funds for the development of such a design, that is why the radio electronics is actively used by the thermal paste.

Due to improved thermal conductivity, iron developers increase the stability of the work and the cost of their own products. Just imagine how many problems would be manufacturers, with such a pricing policy. And at that moment, when global manufacturers realized this truth, a first sample of a special paste appeared, endowed with first-class properties. It can be said that it was at this stage that a real revolution occurred in the cooling of iron. I didn't even dream about Iron Schwarzenegger, when I went to the past.

So, before you begin to read the main part of the section "Replacing thermal Pasts", arche with the following tools:

thermobotian itself
set of screwdrivers
cleaning aided
dry napkins.

With screwdrivers, you can access the insides of the computer. There are such models of "boxes", which does not require a screwdriver, nor Bulgarian - everything keeps on latches. Napkins and cleaning agents will be suitable for removing old paste.

At the first stage, do not forget to turn off the PC from the network and the periphery. Open the cover of the system unit under which the radiator with the processor is hidden. Most likely, you use classic models from AMD or Intel with "native" radiators. As soon as you get to the motherboard chip, you should disconnect the cooling system. It is not difficult, it is fixed with simple latches or vibration pairs. And do not forget to clean the radiator from dust.

Do not forget to remove the old thermal path.

If she tightly sucks you to help the alcohol to soften the thermal and flat screwdriver, if it does not help anything at all (it should be scraped very carefully, without damaging the processor or cooling system) a new layer that is superimposed after removing the old one, should be very thin. You can smear it with a plastic card. Although for this purpose, the finger will be perfect.

As soon as these operations are completed, you can assemble the device in the reverse order. Turn on the computer and check its performance. Moreover, I recommend to hold the computer in active mode at least one hour. If your PC has returned to your PC, then accept my congratulations!

If the replacement of the thermal paste did not bring the desired result, then the system unit should be disassembled again. Check how dense radiators are pressed. It is possible that you have fallen too little / many paste, which is why the normal heat exchange was broken. Try adding / removing a bit of the thermal paste and check the performance of the device again.

If you use a secondary cooler, other than the standard, recommend carefully examine its mount. Do not neglect the advice of experienced users and printed instructions. If you need to remove your motherboard, it is best to use a special tool. Sometimes the motherboard does not allow you to safely disconnect the cooling system, so you have to disassemble everything thoroughly. Or attribute your device to the nearest service center.

And the last question that is interested in everyone. How often does the replacement of the thermal paste? Based on your own experience, I will say that a new paste can be applied once every year and a half. At about the same time interval, clean the computer from dust should be cleaned.

In this video, everything is in detail and clearly shown! Good luck! \u003d)

Despite the small dimensions, the processor is, it is possible to say the heart of a personal computer and it should work, respectively, properly. But, performing hundreds of operations per second, the processor is very strong heats up Because of what could fail, simply burners. It is to prevent such a situation and need thermoplasticwhich is an additional cooling element.

So, thermoplast is substancewhich is applied thin layer on the processor for better heat sink.

Most cooling Takes on me cooler and ventilation, since they are capable of less than 15 seconds to cool even the most hot processor, and thermoplast is needed only for improvements Clutch cooling element with device.

Many users wonder - why do you continue to change the paste? Over time, its layer dries And it all less and less effectively fulfills its functions. As you already understood, the absence of a protective layer leads to overheatingwhat in turn will cause unstable the work of the operating system itself (the OS is trying limit performance in order to downgrade the temperature of the hardware computer), and also tries to secure the entire hardware of the PC, as the processor together with other elements can burn. So periodically, but still recommended Replace the thermal colon.

In addition, you need to choose the paste. Best Products are considered heat sir Elements (for example, silver), which are several times improving the heat exchange process between the elements of the PC. When applying such a paste, a thin layer of the substance itself and an additional silver layer, which takes place heat.

How to apply the thermal

Quality cooling directly depends on the proper application of paste. The slightest flaws at times will reduce the efficiency of cooling even the most powerful system. Maintenance principles Such:

Not worth it remove the radiator after installation to check the thermal paste is uniformly distributed. Thus, you break the adhesion of surfaces and have to start the process again, completely removing the already applied layer.

Replacing the thermal paste on the processor

Before proceeding with the replacement of the paste, it must be purchased. It costs about 150 rubles per tube. Well, now, you can proceed:

We change the thermal chaser on the video card

The essence of the replacement paste on the video card is as follows:

Replacement Thermal Paste on Laptop

Replacing the thermal paste on a laptop is practically nothing is not different In replacing a personal computer. The only thing is to note that the hardware elements will be placed on another (the type of element layout depends directly from the model of the laptop and manufacturer). But, as a rule, each device element is in a special cell and it is easy to get it for subsequent processing.

Hello everyone. As promised, I tell about applying the thermal paste. In the last article, I remind you, we learned, and today we will find out how to propose a thermal path.

There were times when information on the Internet was not very much. Upon learning of something interesting, people tried to experience everything themselves, not knowing how to make it and for what. But these are people ... they have logic. Its. Not always logical. As a result, it turned out it is not clear that.

So it was with the first attempts to apply the thermal paste - they did not apply there, not so much as you need:

Now you need to say thanks to the Internet! You can find any information. But it is worth being careful, because not all the information can be trusted.

Proper replacement Thermal Paste on the processor

As I said, not everything you read on the Internet can be trusted. And the advisers are enough. Be careful, you can advise and solidol to use instead of the thermal paste. Yes, I have seen this on the forums.

How often do you need to change the thermal colon?

First you need to understand whether you need a replacement of the thermal paste. Do not listen to the "specialists" that recommend changing it every six months. Brad is all. Yes, it dries over such a period, but it does not mean that it needs to be changed. To your note, just hanging on, it begins to perform their functions by 100%. And when you only applied it, the thermal conductivity will not be maximum.

So remember - no Mandatory Period for Replacement Thermal Past! It is necessary to proceed from the circumstances.

For each individual processor model there is its own critical temperature, so do not strongly adhere to the generally accepted indicators. No standard optimal temperature happens. All individually.

So, if the system malfunctions are precisely due to the processor temperature, then it's time to replace the thermal! In other cases, it is better not necessary.

Still her have to Replace if you remove the cooling system of the central processor. And also it has to be replaced every time in a laptop when the dust is cleaned. Because in a laptop to clean the cooling system from dust, it must first be disconnected from the processor. By the way, if yours, then it is time to clean from dust.

I think the question " How often do you need to change the thermal colon?" I answered. Moving on.

When you remove the cooler radiator from the processor, then on the processor and on the radiator you will see the remains of dry thermal paste. Before applying a new one, you should get rid of the old, otherwise the benefits of replacing the thermal paste you will not notice.

By the way, sometimes it happens that the radiator is so tightly dares to the processor that they are not so easy to discharge. Do not try to use a knife, screwdriver or other flat metal objects in this case. It will be enough to twist them along the central axis with the use of coarse force. But be careful, do not blame the feet of the processor.

The second way to dedicate the radiator from the processor is to heat them with a hairdryer. Take your wife or mom (or at the daughter) a regular hairdryer for drying hair and heat the processor for 1-2 minutes. Under the influence of the temperature of the thermal paste will be a little softer, even despite the fact that it is dry. This is due to the fact that its composition includes metal pollen, and any metal when heated becomes a little more elastic.

If everything went well, then you will have a processor in one hand, and in the other - the radiator. Now you need to erase the old thermalist and from the processor and from the radiator. This is done with cloth or cotton. And if it moves badly, then eraser (erasing rubber). And if everything is completely bad, it is worth using alcohol. Just do not overdo it.

In no case do not erase the old thermal gloss with rude objects, because you can damage the plane, create microscopic scratches on it, which will be unfavorable for heat dissipation.

We summarize. Than wipe the old thermal From the processor and radiator cooling? Answer - cloth, cotton, soft paper, eraser and can be used alcoholBut not cologne, only pure alcohol.

So we got to the most important issue of today - applying thermal stas. If you search for something like " proper replacement of the thermal paste" or " proper applying thermal stas"I assure you, you just get confused. You will come across the overwhelms, under each video there will be dysletes almost as much as likes and a whole bunch of brahi.

Someone delivers her one drop in the middle of the processor, someone flashes like a sandwich. There are people who experiment and apply it then around the perimeter, then in the center, then a plus, then a cross, then a strip, then in a checker order. So what? The difference in the end is 1-2 degrees!

Now you know what right replacement thermal paste when and rules"It's essentially no." Such a paradox. Good luck in application! \u003d)

Have you read until the very end?

Was this article useful?

Well no

What exactly did you not like? The article was incomplete or untruthful?
Write in climmenia and we promise to correct!

Content

Computer / laptop care is an important procedure that needs close attention. This is especially true of cooling the processor - one of the main elements of the PC. The struggle against high temperatures implies a systematic substitution of the thermal paste - substance that does not allow to overheat key parts of computer "iron".

Why do you need a thermalcase on the processor

The viscous fluid, called the thermal storage, is necessarily applied to the processor before installing the radiator on it. Many are mistaken that the mass is needed for rapid cooling of the chip: in fact, it serves as one goal - fast thermal conductivity from the chip to the cooler, which displays hot air. This process is very important for a computer or laptop, because otherwise the processor (primary or video card) can simply overdo it. Then the replacement will be required, and this part of the PC is not cheap.

The replacement of the thermal paste on the processor is desired with each cleaning of the laptop, and the operation itself requires the highest accuracy and attentiveness. Improper application of the substance can cause damage to the computer and eventually lead to the purchase of important details. One tube should be enough for several planned care procedures. It is desirable to change the heat-conducting mass immediately and on the motherboard and on the video card, because it is not easy to disassemble and collect the computer.

What thermal chaser to choose for the processor

With the advent of a large number of equipment that requires constant control of thermal conductivity, more and more manufacturers offer their own thermal paste to buy. The choice is really wide, but attention should be paid to the quality of the product. Household appliances stores can be found both domestic companies and foreign, specializing in pastas. The most famous lubricant in the Russian market is KPT-8, which, although it has an impressive age (and invented it in the USSR), is distinguished by its high characteristics, heading of users.

To domestic thermal caps that are allocated among the others can be attributed to Alsil from GM-Inform. The main elements of this product are aluminum nitride and high-quality silicone (for viscosity). I also want to note the choice of such manufacturers as Titan Silver Grease, Zalman, Gelid GC-Extreme and Noctua NT - these foreign liquids for cooling in the syringes passed all quality tests and easily cope with all tasks. The price of all these products is low, so everyone can afford such protection against heat for a computer.

Price Thermal Processor

If suddenly it urgently needed a thermalcaste for a processor, then you should know what it costs it is inexpensive - from 200 to 500 rubles. Agree, this is not a very big price for such a useful and effective thing. The product can be easily ordered / buy in the online store (order with delivery in Moscow and other corners of Russia) or to purchase sales in retail points (household appliances supermarkets).

Below is a table of comparison top lubricants with a difference in thermal conductivity coefficients and prices. All of them show an excellent result of efficiency as coolers. The choice of a particular mass depends exclusively from the buyer. Those people who figured out how to properly apply a thermal power to the processor and fulfilled all actions correctly, won't notice a big difference in the cooling system.

Thermal CPU thermal paste	Coefficient of thermal conductivity	Cost (rubles)


Titan Silver Grease.
Zalman ZM-STG1 / 2	11
Gelid GC-Extreme
ASUS THERMAL EXTREMELY.

How to apply thermal processor

The process of removing the old and applying a new lubricant on the main details of a laptop or PC labor-consuming, painstaking. Before replacing the thermal chaser on the processor, you need to do a number of certain consecutive preparatory manipulations. For example, remove the laptop cover without damaging the insides, and clean the entire workspace from dust (you can use the vacuum cleaner). How to properly apply a thermal chaser for the processor:

After the surface cleaning of the laptop from dust and garbage, with a screwdriver, disconnect the radiator from the processor.
Use the rut dipped in alcohol to remove the layer of the previous thermal splash with the chip.
When changing the thermal paste carefully make sure that the new layer is thin and distributed over the entire surface of the processor.
Take a tube with one hand, look out a small amount of mass (several grams) directly on the chip, distribute all the area with any plastic card or other fixture.
Try not to stain the heat-conducting mass of the motherboard surface, do not hurt contacts.
After the procedure, not allowing to dry the working material, "plant" back the radiator, tightly pressed the paste between it and the chip.
Do this procedure with a video card processor.
Do not forget to gently fasten all the screws, while not disturbing the integrity of the "iron" of the computer.

Hello, friends! In this article, tell about the replacement of the thermal paste. Why do you need to do? How often do you need to do? And how it is done at all. The thermalcase is a paste similar to a tooth (may be white or gray), which has good thermal conductivity. Purpose it, help to remove heat from to cooling systems. In particular from and. In the system unit there are more devices from which it is necessary to remove heat using a radiator, such as chipsets or bridges on. Not in all cases use the thermal colon.

Open the system unit. It is usually enough to open one of the housing covers. Most likely you have a regular cooler for the Intel or AMD processor.