Typical configuration of Tp-link routers. How to correctly configure a purchased wifi router brand tp link wifi connection tp link

In this small step-by-step instruction "for dummies" I will show you how to connect your router to your computer using a network cable. If we are talking about a laptop that does not have a network connector, then this will not work - it must have an Ethernet port, or make a connection via WiFi. You can also configure the router either through the web interface or using the utility on the CD. Let's take a look at all the possible options. I will keep in mind the connection of TP-Link TL-WR740N and TL-WR741ND routers, but this guide is suitable for any model. It makes no sense to make a separate manual for each separately, since they are connected to a computer and the Internet and they are configured exactly the same, the only difference is in insignificant nuances depending on their technical characteristics.

Connecting the router to a computer via a network cable

So, the first option is to connect the router to the computer using a network cable that is included in the box for any device of this type. Usually, a stationary PC does not have a wireless module, so it makes sense to connect it with a wire.

In this case, it is necessary to strictly observe the purpose of the ports - that is, the connectors located on the back of the router case.

WAN - used to connect a cable from an Internet provider to it

LAN - for a patchcord from a computer

That is, we take out the Internet wire that was previously inserted into the computer and connect it to the router port, which is marked as WAN and often has a different color from others. Read about what to do if, separately.

Next, we insert the Ethernet cable with one end into the network connector of the PC - to where the wire from the provider used to go, which was brought to your apartment when the Internet was connected. It is located on the back of the computer case. On a laptop, you need to look for it from the back or side

We connect the other end to any of several LAN ports on the router.

Installing TP-Link Router via PC

"Start - Control Panel - Network and Internet - Network and Sharing Center - Managing network connections - Changing adapter settings." Here we see "Local Area Connection". Click on it with the right mouse button, go to "Properties" and open "".

If something is written here, then we carefully rewrite it on paper, after which we put a check mark on "Get IP address" and "Get DNS servers" - AUTOMATICALLY

We save all the parameters.

How to connect TP-Link router to laptop via WiFi?

Often, it is not possible to connect a router to a laptop via a cable, since the latter does not have a corresponding connector on the case. But this is not a problem, since all modern TP-Link routers have the ability to do this over WiFi. As soon as you plug it into the network, it will start distributing a wireless network with a name like "TP-LINK_XXX", which is open for the connection.

But first, just like in the first case, you need to go to "Change adapter parameters", only this time select "Wireless network connection" for editing

And we also put the checkboxes on the "machine".

After that, we connect to this TP-Link wireless network. In newer modifications, it happens that it is still protected by a password (PIN) - if so, you can find it on a sticker on the case.

How to connect TP-Link router on a laptop without a disk?

The easiest option for further actions is to open a browser and enter the ip address at which the router's admin panel is located. For TP-Link, in most cases it is 192.168.0.1, but in some models it is also 192.168.1.1 - you can clarify this on the sticker located at the bottom of the device. There is also a login with a password to enter.

After getting into the control panel, it is enough to launch the quick setup wizard and go through the entire process of connecting the Internet step by step:

select connection type
enter data for authorization
configure wifi network

For more information about installing a Tp-Link router without a disk through a browser on a computer or laptop, see the article about and.

Installing and connecting a computer to a router using a CD

Any TP-Link wireless router comes with a licensed disk with an installer in the box, with which you can connect to the Internet and set up wifi distribution. By and large, it is not needed, since it is easy to set all the necessary configurations in the admin panel through a regular browser, as we have already seen. However, since such a possibility exists, why not figure out how to use it?

It makes sense to connect TP-Link to the Internet through a special utility that comes with the installation disk if you do not need any subtle delicacies in the network parameters. It is much easier and more convenient to use step-by-step instructions that will tell you what to do. To do this, insert the CD into your computer's drive and install the Setup Wizard.

Since it is universal for different models, first you need to select the TP-Link TL-WR740N or TL-WR741ND model from the list

and follow the detailed instructions.

We connect the router to the computer using a patchcord - one end to the network port of the PC, the other to the LAN connector of the router. It is usually highlighted in yellow
We connect the router to the Internet cable, which we insert into the WAN connector - it is marked in blue
We turn on the router to the power grid
Checking the operation of the light indicators on the case
We are waiting for the router to connect to the computer

Wifi setup

After that, we select the type of encryption and set our invented username and password for the connection. The most reliable today - choose it.

If everything went well, then the last window will notify you of this:

As you can see, there is nothing difficult about connecting the router to a computer via a network cable or a laptop via wifi - any beginner can do this!

Thanks! Did not help

In this tutorial, we will show you in detail how to set up your TP-Link router. The TP-Link Wi-Fi router is available in several modifications and for writing this article we used the TP-Link WR841 N router as an example. However, this instruction is quite suitable for the following models: TP-Link TL-WR740N and TP-Link TL -WR741N. Do not close the page, even if you have a TP-Link WiFi router of another modification. In any case, there will be no significant differences, so we read the article and repeat all actions according to the instructions.

As for connecting a TP-Link router, here the scheme is standard: We connect the router to the mains, insert the cable from the Internet provider into the WAN port, connect the network cable from the computer to the LAN socket.

You can read more about the general rules for installing and connecting a router of any model. So, there shouldn't be any questions regarding the connection, so we can immediately start configuring the TP-Link router.

Configuring a TP-Link router

Before setting up a TP-Link router, it is advisable to reset the existing settings. This is done quite simply. Each router has a special button for resetting the router's settings "Reset". We press this button and hold it for about 30 seconds, after which the router should reboot and the settings will be reset.

Now you can start configuring your router. To do this, you need to get into the web interface of the router. To do this, open any browser and enter 192.168.0.1 in the address bar. If the login fails, we try to enter 192.168.1.1.

Note: the address to enter the router interface may differ depending on the firmware installed on the device. Usually, initially the login is carried out through 192.168.0.1, and after the firmware update through 192.168.1.1.

After going to the above address, you will see a window in which you need to enter your username and password. For TP-Link routers, the default username is "admin" and a similar password. If the default password and login are not suitable, then look at the router's documentation, it will certainly contain all the necessary information. There is also information for entering the web interface of settings on a sticker on the bottom of the Wi-Fi router.

So, after entering the username and password, we press "send" and get into the web-interface of the Wi-Fi router, here we will perform all the necessary settings. First of all, we need to update the TP-Link firmware to the latest version. Before downloading the firmware, you need to determine the hardware version of our router. It will be listed on the back of the router.

In our case, the version "Ver: 7.2" is used, therefore, we need to download it. You may have a different hardware version, but the essence remains the same. We go to the site http: // www.tp-linkru.com and enter the model of our Wi-Fi router into the search bar on the site, as mentioned earlier, our instructions are based on the example of the TP-Link WR841 N router. You enter your model and click find. Select the appropriate model from the list. Next, look for the "Downloads" tab, go to it. Now we need the "Software" section, where we need to select the "Firmware" item. Here we are looking for the hardware version of your device and download the first firmware in the list. Unzip the firmware file to your computer and return to the wifi router settings menu.

Now we need to install the latest firmware we just downloaded. To do this, go to the "System Tools" section and select the "Firmware Upgrade" item. Now click "Browse" and specify the path to the firmware file, then click "Upgrade". Next, the router will automatically update the firmware and you will find yourself on the main page of the web interface.

Now you can proceed to the basic settings of your TP-Link router. Let's start by changing the username and password to enter the router settings. To do this, open the "System Tools" section, select the "Password" item and enter the desired data, then click on the "Save" button for all settings to take effect.

How to set up the Internet on a TP-Link router

The floor is done. Now you need to complete the network settings. To do this, look for the "Network" section in the main menu of the interface, then select the "WAN" item, where we need to select the type of network. The type of connection depends on which Internet provider you are using. You can find out the necessary information in an agreement with the provider or on the official website of the service provider.

After selecting the type of network, go to the "MAC Clone" tab, where you need to select the "Clone MAC Address" item and click the "Save" button.

How to set up a Wi-Fi network on TP-Link

In principle, the Internet should appear after performing the above actions, however, we recommend that you also configure the Wi-Fi network. To do this, look for the "Wireless" section and in the "Wireless Network Name" field indicate the desired name for your Wi-Fi network.

We save the settings and go to the "Wireless Security" section. Here we need to configure the security settings of our Wi-Fi network, that is, come up with a password. In principle, you don't need to change anything, but then anyone can connect to your Wi-Fi network, so it's better to set a password anyway. To do this, enter the desired password in the PSK Password field.

If everything was done correctly, then there should be no problems with Internet access. Now you know how to set up a TP-Link router, if you have any questions, ask them in the comments or in the "ask a question to a specialist" section.

TP-Link is a major manufacturer of a wide variety of network equipment: home wireless routers, Wi-Fi network amplifiers, Wi-Fi adapters and much more. In this article, we will take a closer look at the process of setting up WiFi on TP-Link, step by step and with screenshots.

TP-Link Network Equipment

To begin with, it's worth saying a few words about the TP-Link equipment manufacturer itself. This large company has been a supplier of modern technology for Internet access for many years. Routers and adapters of this company are at home for many users, so very often the question arises about setting WiFi on TP Link, how to do it correctly and how to achieve maximum Internet performance on wireless devices.

The manufacturer offers a wide range of equipment: home routers, Wi-Fi amplifiers, ADSL and 3G modems, Wi-Fi adapters, smart home equipment, access points, antennas, etc. Correct configuration of these devices is required for correct operation.

Connecting a TP-Link home router

In order to configure WiFi on TP Link, we need the following:

directly the router itself;
a computer or laptop (a device that can be connected using an Ethernet cable);
twisted pair;
network cable through which the provider provides access to the Internet.

Connect the router to the power supply, make sure that the indicators on it are on (that the device is correctly connected to the network is indicated by the steady light POWER indicator).

Then connect the WAN cable from the outside of the apartment to the connector (this is necessary so that after configuration, access to the network appears). The ports on the router look like the photo below. The connector for the cable from the provider is highlighted in a different color.

Connect the twisted pair cable with one end to any of the LAN connectors (yellow), and the other - to the connector of the computer's network card. The WAN and LAN 1 indicators on the router should be on.

Configuration via the WEB interface

After that, you need to enter the interface to configure WiFi for To do this, in the address bar of any browser, you need to enter the IP address of the router. Usually this is 192.168.1.1 or 192.168.0.1. If none of these addresses are suitable, the correct one can be found on the information sticker on the router.

After that, in the authorization field that opens, you need to enter the admin login and exactly the same password. Again, if no data is being received, check the sticker. In the event that no input values are accepted, it is recommended to reset the router settings by pressing the Reset button.

So, after that you will be taken to the router settings interface. It looks like this.

It is worth noting that configuring WiFi on TP Link is convenient because most models have a standardized web interface that is intuitive even for an inexperienced user, and the official website offers emulators for all popular equipment models.

To configure the wireless network, on the left in the menu, select the Wireless item, in the submenu that opens - Wireless Settings.

The following window will open.

In it we will set the basic settings of the access point.

In the SSID section, you need to enter the name (name) of your wireless home network. It can consist of Latin letters and numbers.
Choose the region you are in.
In the Channel line, you can leave the value "Auto", then the router will choose the most unloaded channel at each reboot, or you can choose any other by analyzing the networks in your house using special utilities. It is important to pay attention to the fact that in the event that you use Apple devices, you need to select channels in the range from 1 to 11.
Leave the rest of the settings as default and click the Save button.

The basic wireless settings are now complete.

Set up a password

Go to the Wireless Security section, where you can set a password for the network. To do this, just put a full stop on the WPA-PSK / WPA2-PSK item and enter the desired password. For safety, it is better to use the most complex combinations of lowercase and uppercase Latin letters and numbers.

The basic configuration of the TP Link WR841N WiFi router at this point can be considered complete. Experienced users can use the official emulator on the manufacturer's website to configure advanced settings according to their needs.

Setting up a wireless network on a TP-Link ADSL modem

Many Internet users from providers such as Rostelecom connect using ADSL technology. Modern modems using this type of connection can distribute a wireless network. Let's figure out how to configure WiFi on TP Link TD W8961ND.

Since the configuration is done using a telephone cable, make sure it is plugged into the appropriate jack on the back of the router. This is a gray connector and is different in shape from the four LAN connectors highlighted in yellow. This is what it looks like.

The interface is entered in a manner similar to that described in the previous paragraph, but visually the settings screen is somewhat different.

From the menu at the top, select the Interface Setup section and go to the Wireless tab. Here's what you'll see:

Here, all settings are located on one screen. We are interested in the following points:

Check that there is a point at the Access Point (Activated).
Select Russia from the list of countries, set the desired wireless channel. It is not necessary to change the rest of the settings in this block.
Then go down to the bottom of the page and enter the desired network name in the SSID line, specify WPA / WPA2-PSK in the Authentification Type field, TKIP should be set in the Encryption.
Enter the password at your discretion.

As you can see, setting up WiFi on TP Link W8961ND is a snap. After all the data has been entered, restart the router, find your network on the wireless devices in the list of available ones and start using the Internet.

Specifics of setting for Rostelecom

In some regions, TP Link devices are provided by the largest Russian provider, Rostelecom. In addition, modems and routers from this company can be purchased independently.

Setting up TP Link WiFi routers under Rostelecom is practically no different from the settings for other providers.

If you are using an ADSL modem, then enter the data in the same way as in the previous paragraph. In addition to configuring the wireless network, you may need to set the connection type on the modem. As a rule, Rostelecom uses a PPPoE connection, the login and password for which can be specified in the technical service.

When connected using GPON or Docsis technologies, the router is used as an auxiliary device. The connection itself is made through the terminal, or In these cases, the router will be connected using an additional network cable to the main network device.

In order to configure WiFi on TP Link for Rostelecom, you need to go to the web interface in the same way and enter the desired data. Usually, the provider does not put any restrictions on the operation of the wireless network.

Tip: if the setup was performed by a specialist when the service was connected, it is recommended to change the default network name and password, because devices with default data are most often hacked.

Configuring the Wireless Amplifier

An amplifier, or repeater, of a Wi-Fi network is a device that allows you to use wireless devices over a much wider area. It is connected in cases where the area of the apartment exceeds the coverage area of the router.

Let's take a look at how the TP Link WiFi Amplifier is configured.

If the device is connected for the first time, a basic setup is performed, thanks to which the device knows which router it will communicate with in the future.

Connect the repeater to the computer with a network cable.
In the browser, enter the IP address 192.168.0.254, log in by entering a standard pair of username and password.
You will be taken to the quick setup menu. Follow the prompts on the screen. Once you select a region, it will search for available wireless networks. Select yours and click "Next".
Enter the SSID and password for your network, go to the next screen, make sure the settings are correct and complete the wizard.

This is what the TP Link repeater quick setup screen looks like.

Through the same web interface, after completing the basic settings, you can configure other parameters of the wireless network, for example, set the type of encryption and the key to the network.

Repeater connection

After WiFi TP Link is completed, plug the repeater into an electrical outlet in the place where the signal of the main router is decreasing, make sure that the indicator on it is on.

Press the WPS button on the main router, and within 30 seconds after that press the large padlock button on the repeater. An indicator appears showing the wireless network level. Two or three bars on it indicate that Wi-Fi performance will be good.

How to choose a Wi-Fi adapter

It is often required to connect a device via a wireless network that does not have a built-in Wi-Fi module, for example, a desktop computer. In such cases, special adapters are used to enable such equipment to receive the wireless signal.

The range of such devices is very extensive, therefore, depending on the required functionality, you can choose a suitable adapter.

If you are using a laptop that does not have a built-in Wi-Fi module, or this module is damaged, you can use a compact adapter, for example, TP-Link TL-WN725N.

In cases where you need to work wirelessly on a stationary computer located far from a Wi-Fi source, it is better to purchase an adapter with an external antenna.

The Wi-FI adapter can be connected via USB or PCI (internal).

Step by step setup

How the WIFi TP Link adapter is configured will be discussed further.

First, connect it to your computer using the appropriate connector. If the system unit is on the floor, it is recommended to use a USB extension cable to position the adapter higher for a better signal.
Next, you need to install the driver. It can work automatically - then you will immediately see the available Wi-Fi networks, but if the operating system did not load it right away, you can install it from the disc that comes with the adapter, or download it from the manufacturer's official website.
If you download the driver yourself, you need to know its version - it is indicated on the package or sticker. There are V1 and V2 versions.
Download the driver, launch it and follow the instructions on the screen. It is enough to click "Next" several times without changing any parameters, and the driver will be installed, after which access to the wireless network will appear.

By setting up the equipment according to these instructions, you will be able to connect to the Internet anywhere in the apartment without cluttering the space with a large number of wires.

As you can see, configuring WiFi on TP Link is not a big deal for users. An intuitive interface, publicly available firmware emulators and a large amount of available information make this process very convenient for everyone.

To make the wireless network work properly, here are some recommendations.

No device can work uninterruptedly for a long time, therefore it is recommended to reboot the equipment at least once every two to three weeks.
When using a large number of Wi-Fi devices, it is best to use a router that supports a 5 GHz network. It is important to remember that many budget or older models of smartphones and tablets may not be able to connect at this frequency.
In apartment buildings, the same Wi-Fi network channel can be occupied by a large number of devices. You can analyze the network with special utilities and change the channel in the settings to increase the speed of the Internet over a wireless network.
When giving preference to budget models, you need to remember that they can work very efficiently and stably, however, they often support a speed lower than what can be stated by your provider. Therefore, when buying a new router, always pay attention to the technical specifications.

Many users believe that wireless technology is significantly inferior to a cable network connection, but with the correct use of technology and following the basic rules of its operation, you can achieve very good results.

Conclusion

It is already very difficult to imagine working on the Internet without the ability to connect devices wirelessly. In this article, we have covered the basic WiFi settings on TP Link. Our recommendations will allow you to always stay connected and do what you love on the web.

Nowadays, unlimited high-speed Internet is no longer a novelty. And even more so when it comes to a wireless connection option, which is applicable even for a personal computer, not to mention laptops, tablets or smartphones. Nowadays, most mobile devices have a built-in WiFi module, and their comfortable use directly depends on how high-quality wireless connection is installed in your home and how well everything can be connected to a computer.

TP-Link WiFi routers are a good example of solving problems with speed, range and antenna power. Also, you are guaranteed to get rid of wires in your apartment. After you have purchased a router, it is very important to understand how to properly connect the device to your computer yourself. The fact is that if you already have an Internet connection, then the lack of knowledge on this issue can lead to additional costs for calling specialists.

In this article, we will try to tell you how to properly connect your TP-Link to your computer and make its subsequent configuration.

Computer connection

The first step is to open the box and make sure that the package bundle of the TP-Link router corresponds to that described in the documentation. That is, make sure that all the elements are in place. In addition to the router itself, you need a power supply, cables, and a software disc.

Before connecting a TP-Link router to your computer, you need to place it correctly. It is best to place the cable close to where your PC sits, as the supplied cable is not too long. If this fails, a longer cable can be purchased separately. It is very cheap and is sold in any electronics store.

The TP-Link router has the following buttons and connectors, most of which we will need when connecting and configuring:

power button;
WAN connector for connecting the router to the Internet;
LAN connectors for connecting a PC using a network cable;
disabling and enabling the QSS function;
button to reset the router settings.

After you have familiarized yourself with the location of the connectors, you need to connect the power supply to the TP-Link router, and plug the unit into a power outlet. The WAN socket located on the device body is connected to a cable that was conducted by the provider, that is, it connects directly to the Internet. TP-Link is configured with at least four LAN ports, so you can connect four personal computers at once if you use a network cable.

Configuring TP-Link Router

Before proceeding with the setup, experts recommend performing a preliminary reset to factory settings. After the router has rebooted, use any browser. Enter 192.168.0.1 in the address bar. Another option is 192.168.1.1, depending on the firmware version. You will automatically access the "Configuration Wizard".

To get inside, enter your password and login. By default, both lines are admin. For further security of the network, it is better to change the password during the pre-configuration in question at the moment. To change the input data, go to the System Tools tab, where you need to click on Password. In the Old User Name and Old Password fields, you will need to enter the factory login and password, that is, admin. Come up with a username and password. In principle, you can leave the old login as well. Enter the new data in the New User Name, New Password, Confirm New Password fields. The last field is the confirmation of the new password. Don't forget to save your updates by clicking Save.

On the setup page, you can optionally download and install the latest firmware version immediately. The installation itself is carried out through the System Tools menu, where you need to go to the Firmware Upgrade field. In it, you should click on Browse, select the downloaded file and click on Upgrade. The download must be carried out only from the official resources of the TP-Link company. Fully licensed firmware is provided absolutely free.

Setting up the Internet in a TP-Link router is done in the Network and WAN menu. The first thing to do is choose the type of network. If you do not know it, then just clarify it by calling the provider's Hotline. After you have selected the type, you need to save the settings, for which you need to click on Save.

After successfully saving, go to the next tab labeled as MAC Clone. There is a Clone MAC Address button on which you need to click, and then save everything with Save.

How to configure a WiFi network on a tp link router

To configure a wireless connection, you need to go to the Wireless tab. There is a field here labeled Wireless Network Name. The name of your network fits into it, and it can be chosen arbitrarily. If desired, you can enter the name of the country in the field below. Remember to save all changes.

On the Wireless Security tab, you can configure the security system, including protection against unauthorized access. To do this, you need to come up with a not too simple password and enter it in the PSK Password column.

All changes in the settings must be saved, after which the router must be rebooted. You need to reboot the device from the Reboot button located on the System Tools tab. After clicking on the button, you just need to confirm your action.

Output

As you can see, there is nothing difficult about connecting and configuring the router yourself. It's really simple and doesn't take long. And you can save money on calling specialists and the time during which you would have to wait for them.

Hey! Now we will connect and configure the Tp-link TL-WR841N Wi-Fi router. If your model is TL-WR841ND, then this manual will also work for you. Consider the entire process of connecting a router, setting up the Internet, Wi-Fi networks and setting a password for a Wi-Fi network.

All this with a photo and a detailed description. So you shouldn't have any problems with configuring the Tp-link TL-WR841N router. Just follow the instructions.

A few words about Tp-link TL-WR841N (TL-WR841ND). A very successful Wi-Fi router model that is very popular. Indeed, a successful model with an excellent price / quality ratio. It seems to me that for home use, an undemanding user cannot find a better router. I myself, in practice, checked the operation of the Tp-link TL-WR841N. It has been working great for more than five years now, distributing Wi-Fi to a large number of devices. It works very stably, I don't even remember that it would once have lost the Internet, or something else. You can read more about Tp-link TL-WR841N at. There you will find a small review, and my review.

If you have already bought this router, then it's time to move on to setting up. Let's do everything according to the following scheme:

Connecting a Tp-link TL-WR841N router.
Setting up an Internet connection (WAN).
Setting up a Wi-Fi network on TL-WR841N.
Setting a password for protecting a Wi-Fi network.
Changing the admin password, which protects the settings of the router.

Connecting Tp-link TL-WR841N

Connect the power adapter to the router, and plug it into a power outlet. If the indicators on the router do not light up, then turn on the power with the button located on the back panel.

If you will be configuring the router via cable (included in the package) by connecting it to a computer or laptop, then take a network cable and connect it to the computer with the router. On the router, we connect the cable to the LAN connector (to one of 4):

We connect the other end of the network cable on the computer to the socket of the network card:

Connection and configuration via Wi-Fi network

If you want to configure the router via Wi-Fi, and not when connecting via cable, then it is enough to connect to the Wi-Fi network, which will appear immediately after turning on the power on the Tp-link TL-WR841N router. The network will have a standard name (something like this: "TP-LINK_084313"), and will not be protected.

You can even connect to this network from a tablet or phone and set up a router without a computer.

You probably found a disc included with the TL-WR841N. There is a utility for configuring the router. So, we will configure without a disk, through the web interface of the router. The disc will not be useful to us in this manual. If you want to configure through the utility from the disk, then you can do it according to the instructions.

The router must be connected to the Internet. And your computer, tablet, laptop, etc. must be connected to Tp-link via cable, or via Wi-Fi. The router must be powered on. If everything is ready, then you can proceed to setting up.

The router settings will open.

And if the router has already connected to the provider and distributes the Internet, then you can continue the configuration.

Setting up a Wi-Fi network and setting a password on a Tp-link TL-WR841N router

To configure Wi-Fi, you need to open the tab on the settings page Wireless - Wireless Settings... On this page we need in the field Wireless Network Name come up with and write down a name for your Wi-Fi network, and in the drop-down menu Region choose the country where you live. Leave the rest of the settings as I have in the screenshot below.

To protect our wireless network with a password, go to the tab Wireless - Wireless Security... There you need to highlight the type of security WPA / WPA2 - Personal (Recommended).

In field PSK Password come up with and write down a password that will protect your Wi-Fi network. You can read more about setting a password on a TL-WR841N router in the article.

Save the settings by clicking the button Save.

Password change admin. Securing router settings

I already wrote in a separate article about how in the settings of the router. Let's, while we are in the Tp-link TL-WR841N settings, immediately change the password that is used to protect the settings page. So that everyone who will connect to your network cannot enter the router settings and change them.

Open the tab System Tools - Password... Please enter your old username and password first (default - admin)... Then, enter your new username below. (you can leave it as admin) and a new password. I advise you to write down this password somewhere so as not to forget. Save the settings with the button Save.

That's all, the configuration of the Tp-link TL-WR841N router is completed. It remains only to reboot the router. This can be done by turning off / on the power, or from the settings. In the tab System Tools - Reboot, you need to click on the Reboot button.

After setting up, and rebooting, a Wi-Fi network will appear, with the name that we set during the setup process. And to connect to a wireless network, use the password that we also set when setting up the router.

You can already connect your devices to the router. If you set up via cable, but want to connect via Wi-Fi, then the laptop can be disconnected from the router and connected wirelessly.

Feel free to leave your feedback and questions in the comments!